LTM8048 - Linear Technology
... pads, so the printed circuit design has a large impact on the thermal performance of the part. See the PCB Layout and Thermal Considerations sections for more details. Apply an external capacitor between VOUT1 and VOUT–. VOUT2 (Bank 3): The output of the secondary side linear post regulator. Apply t ...
... pads, so the printed circuit design has a large impact on the thermal performance of the part. See the PCB Layout and Thermal Considerations sections for more details. Apply an external capacitor between VOUT1 and VOUT–. VOUT2 (Bank 3): The output of the secondary side linear post regulator. Apply t ...
AN4009 Alarm IC Sample Applications INTRODUCTION
... implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes witho ...
... implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes witho ...
LukeOrsini_Project_Draft_20110730.doc
... Today tin-lead solder is used extensively in electronic assemblies. Tin-Lead solder (SnPb) has been used well over a millennium. The Romans used a Sn-Pb alloy to solder pipes. [1] The solder plays an important role in the performance of a circuit card assembly (CCA). For a leadless chip resistor the ...
... Today tin-lead solder is used extensively in electronic assemblies. Tin-Lead solder (SnPb) has been used well over a millennium. The Romans used a Sn-Pb alloy to solder pipes. [1] The solder plays an important role in the performance of a circuit card assembly (CCA). For a leadless chip resistor the ...
LTM8048 - 3.1VIN to 32VIN Isolated uModule DC/DC Converter with LDO Post Regulator
... indicated in Table 1 is not recommended, and may result in undesirable operation. Using larger values is generally acceptable, and can yield improved dynamic response, if it is necessary. Again, it is incumbent upon the user to verify proper operation over the intended system’s line, load and enviro ...
... indicated in Table 1 is not recommended, and may result in undesirable operation. Using larger values is generally acceptable, and can yield improved dynamic response, if it is necessary. Again, it is incumbent upon the user to verify proper operation over the intended system’s line, load and enviro ...
QuickField
... Linear and nonlinear magnetostatics. Transient and time-harmonic magnetics (involving eddy current analysis). Linear and nonlinear, steady state and transient heat transfer and diffusion. Linear stress analysis. Coupled problems. During a 15-minute session, you can describe the problem (geometry, ma ...
... Linear and nonlinear magnetostatics. Transient and time-harmonic magnetics (involving eddy current analysis). Linear and nonlinear, steady state and transient heat transfer and diffusion. Linear stress analysis. Coupled problems. During a 15-minute session, you can describe the problem (geometry, ma ...
SHOT AND THERMAL NOISE
... The uncertainties and correction factors in the parameters you measure (resistance, bandwidth, voltage, temperature) need to be scrutinized. The following points are just some of many considerations to think about. • The noise resistors (in the resistor bank) can be measured quite accurately with a ...
... The uncertainties and correction factors in the parameters you measure (resistance, bandwidth, voltage, temperature) need to be scrutinized. The following points are just some of many considerations to think about. • The noise resistors (in the resistor bank) can be measured quite accurately with a ...
AP7165 600mA LOW DROPOUT REGULATOR WITH POK Description
... The AP7165 is available in the U-DFN3030-10 and SO8EP packages, both with exposed pad, which is the primary conduction path for heat to the printed circuit board (PCB). The pad can be connected to ground or be left floating; however, to ensure the device will not overheat, it should be attached to a ...
... The AP7165 is available in the U-DFN3030-10 and SO8EP packages, both with exposed pad, which is the primary conduction path for heat to the printed circuit board (PCB). The pad can be connected to ground or be left floating; however, to ensure the device will not overheat, it should be attached to a ...
Lumped element model
The lumped element model (also called lumped parameter model, or lumped component model) simplifies the description of the behaviour of spatially distributed physical systems into a topology consisting of discrete entities that approximate the behaviour of the distributed system under certain assumptions. It is useful in electrical systems (including electronics), mechanical multibody systems, heat transfer, acoustics, etc.Mathematically speaking, the simplification reduces the state space of the system to a finite dimension, and the partial differential equations (PDEs) of the continuous (infinite-dimensional) time and space model of the physical system into ordinary differential equations (ODEs) with a finite number of parameters.