LT1764 Series - 3A, Fast Transient Response, Low Noise, LDO
... Note 6: Dropout voltage is the minimum input to output voltage differential needed to maintain regulation at a specified output current. In dropout, the output voltage will be equal to: VIN – VDROPOUT. Note 7: GND pin current is tested with VIN = VOUT(NOMINAL) + 1V or VIN = 2.7V (whichever is greate ...
... Note 6: Dropout voltage is the minimum input to output voltage differential needed to maintain regulation at a specified output current. In dropout, the output voltage will be equal to: VIN – VDROPOUT. Note 7: GND pin current is tested with VIN = VOUT(NOMINAL) + 1V or VIN = 2.7V (whichever is greate ...
cable terminology
... be carried on the outside of the conductor than in the centre (skin effect), and to overcome this problem the larger sizes of conductor are frequently of Milliken construction. Such conductors are formed from several individual sector shapes (usually four for power cables). A thin paper or other sui ...
... be carried on the outside of the conductor than in the centre (skin effect), and to overcome this problem the larger sizes of conductor are frequently of Milliken construction. Such conductors are formed from several individual sector shapes (usually four for power cables). A thin paper or other sui ...
a AN-402 APPLICATION NOTE •
... spike to a voltage extreme. But many downstream circuits like A/D drivers place restrictions on the analog input signal levels in order to maintain their performance. These devices can draw excessive current in an overdrive condition or else be driven into a region of saturation which will have a lo ...
... spike to a voltage extreme. But many downstream circuits like A/D drivers place restrictions on the analog input signal levels in order to maintain their performance. These devices can draw excessive current in an overdrive condition or else be driven into a region of saturation which will have a lo ...
AN4026
... As previously indicated, the PFC acts as master and the resonant stage can operate only if the PFC output is delivering its rated output voltage. Therefore the circuit is designed so that at startup the PFC starts first, the downstream converter then turns on by means of the LINE pin (#7). At the be ...
... As previously indicated, the PFC acts as master and the resonant stage can operate only if the PFC output is delivering its rated output voltage. Therefore the circuit is designed so that at startup the PFC starts first, the downstream converter then turns on by means of the LINE pin (#7). At the be ...
Three-phase, Pad-mounted Distribution Transformers Instructions
... apply. The following are trademarks of GE Company: Sureguard™ GP. R-TEMP® is a registered trademark of Cooper Power Systems. Arc Strangler® is a registered trademark of the Cooper Power Systems. ...
... apply. The following are trademarks of GE Company: Sureguard™ GP. R-TEMP® is a registered trademark of Cooper Power Systems. Arc Strangler® is a registered trademark of the Cooper Power Systems. ...
The-sx-Amplifier-V2.10
... ‘LTP’ - Q1 and Q2 in Exhibit 1), the tail current is fixed by a current source I1. The maximum output current of the diff amp stage available to drive the TIS (Q3 loaded by I2) and any compensation networks (MC, MIC, shunt, etc but in this example C1) is equal to this tail current I1, assuming the L ...
... ‘LTP’ - Q1 and Q2 in Exhibit 1), the tail current is fixed by a current source I1. The maximum output current of the diff amp stage available to drive the TIS (Q3 loaded by I2) and any compensation networks (MC, MIC, shunt, etc but in this example C1) is equal to this tail current I1, assuming the L ...
MAX1895/MAX1995 High-Efficiency, Wide Brightness Range, CCFL Backlight Controllers General Description
... The MAX1895/MAX1995 include safety features that limit the transformer secondary voltage and protect against single-point fault conditions including lamp-out and short-circuit faults. The MAX1895/MAX1995 regulate the CCFL brightness in three ways: linearly controlling the lamp current, digital pulse ...
... The MAX1895/MAX1995 include safety features that limit the transformer secondary voltage and protect against single-point fault conditions including lamp-out and short-circuit faults. The MAX1895/MAX1995 regulate the CCFL brightness in three ways: linearly controlling the lamp current, digital pulse ...
Design overhead distribution systems
... Overhead transmission Overhead conductors are not covered by insulation. The conductor material is nearly always an aluminium alloy, made into several strands and possibly reinforced with steel strands. Copper was sometimes used for overhead transmission but aluminium is lower in weight for equivale ...
... Overhead transmission Overhead conductors are not covered by insulation. The conductor material is nearly always an aluminium alloy, made into several strands and possibly reinforced with steel strands. Copper was sometimes used for overhead transmission but aluminium is lower in weight for equivale ...
Amps and Linear Integrated Circuits
... 8. Determine a suitable circuit configuration to mirror the current from a reference current of 200ua with high input impedance to drive a differential amplifier with common mode input voltage for the following parameters: R = 2K Ω, Kn2= 10 Kn1= 250 µA/ V2 VDD= 5V.http://www.slideshare.net/mujju433/ ...
... 8. Determine a suitable circuit configuration to mirror the current from a reference current of 200ua with high input impedance to drive a differential amplifier with common mode input voltage for the following parameters: R = 2K Ω, Kn2= 10 Kn1= 250 µA/ V2 VDD= 5V.http://www.slideshare.net/mujju433/ ...
The Oscilloscope - Crompton Instruments
... Next, the analog-to-digital converter (ADC) in the acquisition system samples the signal at discrete points in time and converts the signal's voltage at these points to digital values called sample points. The horizontal system's sample clock determines how often the ADC takes a sample. The rate at ...
... Next, the analog-to-digital converter (ADC) in the acquisition system samples the signal at discrete points in time and converts the signal's voltage at these points to digital values called sample points. The horizontal system's sample clock determines how often the ADC takes a sample. The rate at ...
Note 2
... The circuit now enters sleep mode with both power MOSFETs turned off. In sleep mode, much of the circuitry is turned off, dropping the supply current from several milliamperes (with the MOSFETs switching) to 600µA. When the output capacitor has discharged by the amount of hysteresis in comparator V, ...
... The circuit now enters sleep mode with both power MOSFETs turned off. In sleep mode, much of the circuitry is turned off, dropping the supply current from several milliamperes (with the MOSFETs switching) to 600µA. When the output capacitor has discharged by the amount of hysteresis in comparator V, ...
