Download Exploration CCNA4 - College of DuPage

Addressing Services
Accessing the WAN – Chapter 7
Modified by Tony Chen
04/08/2009
ITE I Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
1
Notes:

If you see any mistake on my PowerPoint slides or if
you have any questions about the materials, please
feel free to email me at [email protected].
Thanks!
Tony Chen
College of DuPage
Cisco Networking Academy
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
2
Objectives

In this chapter, you will learn to:
– Configure DHCP in an Enterprise branch network. This
includes being able to explain DHCP features and benefits,
the differences between BOOTP and DHCP, DHCP
operation: and configuring, verifying, and troubleshooting
DHCP.
– Configure NAT on a Cisco router. This includes explaining
key features and operation of NAT and NAT Overload,
explaining advantages and disadvantages of NAT,
configuring NAT and NAT Overload to conserve IP address
space in a network, configuring port forwarding, and
verifying and troubleshooting NAT configurations.
– Configure new generation RIP (RIPng) to use IPv6. This
includes explaining how IPv6 solves any problem of IP
address deletion, explaining how to assign IPv6 addresses,
describing transition strategies for implementing IPv6 and
configuring, verifying and troubleshooting RIPng for IPv6.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
3
What is DHCP?
 Every device connects to a network needs an IP address.
 Network administrators assign static IP addresses to
routers, servers, and other network.
–Administrators enter static IP addresses manually when they
configure devices to join the network.
–Static addresses also enable administrators to manage those
devices remotely.
 Desktop clients typically make up the bulk of network
nodes, DHCP is an extremely useful and timesaving tool
for network administrators.
–DHCP assigns IP addresses and other important network
configuration information dynamically.
•All hosts in the same subnet will receive different IP addresses,
•But will receive the same subnet mask and default gateway
address and DNS server which is common to that subnet.
–In a SOHO location, a Cisco router can be configured to
provide DHCP services without the dedicated server.
•A Cisco IOS feature set called Easy IP offers an optional, fullfeatured DHCP server.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
4
DHCP Operation
 DHCP includes three different address allocation
mechanisms to provide flexibility when assigning IP
addresses:
–Manual Allocation: The administrator assigns a preallocated IP address to the client and DHCP only
communicates the IP address to the device.
–Automatic Allocation: DHCP automatically assigns a
static IP address permanently to a device, selecting it
from a pool of available addresses.
•There is no lease and the address is permanently assigned
to a device.
•[Tony]: “static/permanent automatic allocation”
–Dynamic Allocation (*): DHCP automatically
dynamically assigns, or leases, an IP address from a
pool of addresses
•for a limited period of time chosen by the server, or until the
client tells the server that it no longer needs the address.
•[Tony]: “dynamic/temporary automatic allocation”.
•[Tony]: Client will renew the IP address at 50% and 87.5%
of the length of the lease time.
 *This section focuses on dynamic allocation.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
5
http://en.wikipedia.org/wiki/Dhcp
DHCP Operation
 When the client boots or otherwise wants to join a network, it
completes four steps in obtaining a lease.
1. DHCPDISCOVER (Broadcast)
–The DHCPDISCOVER message finds DHCP servers on the network.
Because the host has no valid IP information at bootup, it uses L2 and
L3 broadcast addresses to communicate with the server.
2. DHCPOFFER (Unicast)
–When the DHCP server receives a DHCDISCOVER message, it finds
an available IP address to lease and transmits a binding offer with a
DHCPOFFER message.
3. DHCPREQUEST (Broadcast)
–When the client receives the DHCPOFFER from the server, it sends
back a DHCPREQUEST message.
•The message is for lease origination and lease renewal and verification.
–Many enterprise networks use multiple DHCP servers. The
DHCPREQUEST message inform this DHCP server and any other
DHCP servers about the accepted offer.
4. DHCPACK (Unicast)
–On receiving the DHCPREQUEST message, the server replies with a
unicast DHCPACK message.
http://www.microsoft.com/te
chnet/prodtechnol/windows2
–When the client receives the DHCPACK message, it knows that the IP 000serv/reskit/cnet/cncb_dh
address is valid and starts using it as its own.
c_nxxi.mspx?mfr=true
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
6
DHCP Operation: Something you needs to know
2. DHCPOFFER (Unicast)
–When the DHCP server receives a DHCDISCOVER message, it finds
an available IP address to lease and transmits a binding offer with a
DHCPOFFER message.
Q: Weather dhcp offer is unicast or broadcast?
Answer:
RFC 1541: The server unicasts the DHCPOFFER message to the
client (using the DHCP/BOOTP relay agent if necessary) if possible,
or may broadcast the message to a broadcast address (preferably
255.255.255.255) on the client's subnet.
The RFC 1541 states that a server "should" try unicast first, but then
can use broadcast when offering. Some OS's like Microsoft skip the
unicast part of this as it is not required.
http://support.microsoft.com/kb/169289
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
http://en.wikipedia.org/wiki/Dhcp
7
DHCP Operation: DHCP Lease Renewal
 Clients lease the information from the server for an
administratively defined period.
 When the lease expires, the client must ask for another
address, although the client is typically reassigned the
same address.
–After 50% of the lease time has passed, the client will
attempt to renew the lease with the original DHCP server
that it obtained the lease from using a DHCPREQUEST
message.
–Any time the client boots and the lease is 50% or more
passed, the client will attempt to renew the lease. At 87.5%
of the lease completion, the client will attempt to contact
any DHCP server for a new lease.
–If the lease expires, the client will send a request as in the
initial boot when the client had no IP address.
–If this fails, the client TCP/IP stack will cease functioning.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
8
BOOTP and DHCP
 The Bootstrap Protocol (BOOTP), defined in RFC
951, is the predecessor of DHCP and shares some
operational characteristics.
–BOOTP is a way to download address and boot
configurations for diskless workstations.
–Both DHCP and BOOTP use UDP ports 67 and 68.
•The client sends messages to the server on port 67.
•The server sends messages to the client on port 68.
 There are 3 differences between DHCP and BOOTP:
1. BOOTP was designed for manual pre-configuration of
the host information in a server database (MAC and IP
entry), while DHCP allows for dynamic allocation of IP
addresses and configurations to newly attached hosts.
2. BOOTP does not use leases. Its clients have
reserved IP address which cannot be assigned to any
other host.DHCP allows for recovery and reallocation of
network addresses through a leasing mechanism.
3. BOOTP provides a limited amount of information to a
host. DHCP provides additional IP configuration
parameters, such as WINS and domain name.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
9
DHCP Message Format
 DHCP maintain compatibility with BOOTP and used the
same BOOTP message format.
–Operation Code (OP) - A value of 1 indicates a request
message; a value of 2 is a reply message.
–Hardware Type - 1 is Ethernet
–Hardware Address length
–Hops - used by relay agents to control the forwarding of DHCP.
–Transaction Identifier
–Seconds
–Flags
–Client IP Address - The client puts its own IP address in this
field if and only if it has a valid IP address while in the bound
state; otherwise, it sets the field to 0.
–Your IP Address - IP address that the server assigns to client.
–Server IP Address - Address of the server that the client should
use for the next.
http://www.networksorcery.com/en
p/protocol/dhcp.htm
–Gateway IP Address - Routes DHCP messages when DHCP
relay agents are involved.
–Client Hardware Address - the Physical layer of the client.
–Server Name - The server sending a DHCPOFFER.
–Boot Filename
–Options
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
10
DHCP Discovery and Offer
 When a client wants to join the network, it requests
addressing values from the network DHCP server.
It transmits a DHCPDISCOVER message on its
local physical subnet when it boots.
–The DHCPDISCOVER is an IP broadcast
(destination IP address of 255.255.255.255).
–The client does not have a configured IP address, so
the source IP address of 0.0.0.0 is used.
–As you see in the figure, the client IP address
(CIADDR), default gateway address (GIADDR), and
subnetwork mask are all marked with question
marks.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
11
DHCP Discovery and Offer
 When the DHCP server receives the
DHCPDISCOVER, it responds with a DHCPOFFER.
–This message contains initial configuration information
for the client, including the MAC address of the client,
–followed by the IP address that the server is offering,
–the subnet mask,
–the lease duration,
–the IP address of the DHCP server making the offer.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
12
Configuring a DHCP Server
 The steps to configure a router as a DHCP server:
– Step 1. Define a range of addresses that DHCP is not
to allocate.
• These are usually static addresses reserved for the router
interface, switch, servers, and local network printers.
• A best practice is to configure excluded addresses before
creating the DHCP pool. This ensures that DHCP does
not assign reserved addresses accidentally.
• Router(config)#ip dhcp excluded-address
– Step 2. Create the DHCP pool
• Router(config)#ip dhcp pool command.
– Step 3. Configure the specifics of the pool.
• You must configure the available addresses.
• You should also define the default gateway for the clients.
• Optional DHCP pool commands:
– IP address of the DNS server
– the duration of the DHCP lease: default setting is one day,
 Disabling DHCP
– The DHCP service is enabled by default
– To disable the service, use the no service dhcp
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
There is no DHCP interface
configuration required.
If a PC is connected to a network
that has a DHCP pool available, it
can obtain an IP address
automatically.
13
Verifying DHCP
 Router R1 has been configured with the following:
R1(config)#ip dhcp excluded-address 192.168.10.1 192.168.10.9
R1(config)# ip dhcp excluded-address 192.168.10.254
R1(config)# ip dhcp pool LAN-POOL-1
R1(dhcp-config)# network 192.168.10.0 255.255.255.0
R1(dhcp-config)# default-router 192.168.10.1
R1(dhcp-config)# domain-name span.com
R1(config)# ip dhcp excluded-address 192.168.11.1 192.168.11.9
R1(config)# ip dhcp excluded-address 192.168.11.254
R1(config)# ip dhcp pool LAN-POOL-2
R1(dhcp-config)# network 192.168.11.0 255.255.255.0
R1(dhcp-config)# default-router 192.168.11.1
R1(dhcp-config)# domain-name span.com
 To verify the operation of DHCP, use show ip dhcp binding
–
This command displays all IP to MAC address bindings.
 To verify that number of messages are being received or
sent by the router, use show ip dhcp server statistics.
 The ipconfig /all command displays the IP on PC.
 To view multiple pools is the show ip dhcp pool command.
–
ITE 1 Chapter 6
This command summarizes the DHCP pool information.
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
14
Configuring a DHCP Client
 In most cases, small home routers are set to acquire
an IP address automatically from their ISPs.
– For example, the figure shows the default WAN setup
page for a Linksys WRVS4400N router.
– Notice that the Internet connection type is set to
Automatic Configuration - DHCP.
– This means that when the router is connected to a
cable modem, for example, it is a DHCP client and
requests an IP address from the ISP.
 Sometimes, Cisco routers in SOHO and branch sites
have to be configured in a similar manner.
– To configure an Ethernet interface as a DHCP client,
the ip address dhcp command must be configured.
•In both of these examples, the routers will
function as both DHCP client and DHCP server.
•It is the client for the ISP
•It is the server for internal hosts.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
15
DHCP (PROBLEM?)
 In a complex hierarchical network, enterprise servers
are usually contained in a server farm.
–The problem is that the network clients typically are not
on the same subnet as those servers.
–Therefore, the clients must locate the servers to
receive services and often these services are located
using broadcast messages.
 In the figure, PC1 is attempting to acquire an IP
address from the DHCP server at 192.168.11.5.
–R1 is not configured as a DHCP server.
–PC1 is unable to locate the DHCP server. Because,
routers do not forward broadcasts.
• Note: Certain Windows clients have a feature called
Automatic Private IP Addressing (APIPA).
• With this feature, a Windows computer can automatically
assign itself an IP address in the 169.254.x.x range in the
event that a DHCP server is not available.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
16
DHCP Relay
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
17
DHCP Relay
 A solution is to configure the helper address feature.
–This solution enables routers as a DHCP relay agent to
forward DHCP broadcasts to the DHCP servers.
–To configure R1 as a DHCP relay agent, configure the
interface to the client with ip helper-address command.
Router R1 is now accepts broadcast requests for the
DHCP service and then forwards them as a unicast to
the IP address 192.168.11.5.
 By default, the ip helper-address command forwards
the following eight UDP services:
–Port 37: Time
–Port 49: TACACS
–Port 53: DNS
–Port 67: DHCP/BOOTP client
–Port 68: DHCP/BOOTP server
–Port 69: TFTP
–Port 137: NetBIOS name service
–Port 138: NetBIOS datagram service
–To specify additional ports, use ip forward-protocol command to
specify exactly which types of broadcast packets to forward.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
18
Configuring a DHCP Server Using SDM
 Cisco routers can also be configured as a DHCP server
using SDM. In this example, router R1 will be
configured as the DHCP server on the Fa0/0 and
Fa0/1interfaces.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
19
Troubleshooting DHCP
Configuration
 Troubleshooting 1: Resolve IP Address Conflicts
–
The show ip dhcp conflict command displays all address conflicts .
R2# show ip dhcp conflict
IP address
Detection Method
Detection time
192.168.1.32
Ping
Feb 16 2007 12:28 PM
192.168.1.64
Gratuitous ARP
Feb 23 2007 08:12 AM
 Troubleshooting 2: Verify Physical Connectivity
–
Use the show interface command to confirm that the is operational.
•
If the state of the interface is anything other than up, the port does not pass traffic.
 Troubleshooting 3: Test Connectivity by Configuring a Client with a Static IP Address
–
If the workstation is unable to reach network resources, the cause of the problem is not DHCP..
 Troubleshooting 4: Verify Switch Port Configuration (STP Portfast and Other Commands)
–
If there is a switch between the client and DHCP server, verify that the port has STP PortFast.
–
The default configuration is PortFast disabled and trunking/channeling auto.
 Troubleshooting 5: Distinguishing Whether DHCP Clients Obtain IP Address on the Same
Subnet or VLAN as DHCP Server
–
ITE 1 Chapter 6
If the DHCP is working correctly, the problem may be the DHCP/BOOTP relay agent.
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
20
Verify Router DHCP/BOOTP Relay Configuration
 If the IP helper address is not configured
properly, client DHCP requests are not
forwarded to the DHCP server.
 Follow these steps to verify the configuration:
–Step 1. Verify that the ip helper-address command is
configured on the correct interface.
•It must be present on the inbound interface of the LAN
containing the DHCP client workstations
•It must be directed to the correct DHCP server.
–Step 2. Verify that the global configuration command no
service dhcp has not been configured.
•This command disables all DHCP server and relay
functionality on the router.
•The command service dhcp does not appear in the
configuration, because it is the default configuration.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
21
Verify that the Router Is Receiving DHCP Requests Using debug Commands.
 As a troubleshooting task, verify that the router is
receiving the DHCP request from the client.
 This troubleshooting step involves configuring an access
control list for debugging output.
–access-list 100 permit ip host 0.0.0.0 host 255.255.255.255
–debug ip packet detail 100
 The output shows router is receiving the DHCP requests.
–The source IP address is 0.0.0.0 because the client does
not yet have an IP address.
–The destination is 255.255.255.255 because the DHCP
discovery message from the client is a broadcast.
–The UDP source and destination ports, 68 and 67.
 Verify that the Router Is Receiving and Forwarding
DHCP Request Using debug ip dhcp server packet
–This command reports server events, like address
assignments and database updates.
–It is also used for decoding DHCP receptions and
transmissions.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
22
Private and Public IP Addressing
 All public Internet addresses must be registered with
a Regional Internet Registry (RIR).
–Only the registered holder of a public Internet address
can assign that address to a network device.
 Unlike public IP addresses, private IP addresses are
a reserved numbers that can be used by anyone.
–To protect the public Internet address structure, ISPs
typically configure the border routers to prevent privately
addressed traffic from being forwarded over the Internet.
–You may have noticed that all the examples in this
course use a private number of IP addresses.
RFC 1918 provides details
–Packets containing these addresses are not routed over
the Internet, and are referred to as non-routable
addresses..
–By providing more address space than most
organizations could obtain through a RIR, private
addressing gives enterprises considerable flexibility in
network design.
However
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
Please do not call
RFC1918 address
non-routable
addresses.
23
Private and Public IP Addressing
 However, because you cannot route private
addresses over the Internet, and there are not
enough public addresses to allow organizations
to provide one to every one of their hosts,
networks need a mechanism to translate private
addresses to public addresses at the edge of
their network that works in both directions.
– Without a translation system, private hosts
behind a router in the network of one
organization cannot connect with private hosts
behind a router in other organizations over the
Internet.
 Network Address Translation (NAT) provides
this mechanism.
– Using NAT, individual companies can address
some or all of their hosts with private addresses
and use NAT to provide access to the Internet.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
Please do not call
RFC1918 address
non-routable
addresses.
For a more in-depth look at
the development of the RIR
system, see the Cisco
Internet Protocol Journal
article at
http://www.cisco.com/web/
about/ac123/ac147/archive
d_issues/ipj_44/regional_internet_registri
es.html
24
What is NAT?
 NAT has many uses, but its key use is to save
IP addresses by allowing networks to use
private IP addresses.
–NAT has an added benefit of adding a degree of
privacy and security to a network because it hides
internal IP addresses from outside networks.
 A NAT-enabled device typically operates at the
border of a stub network.
–When a host inside the stub network, say PC1,
PC2, or PC 3, wants to transmit to a host on the
outside, the packet is forwarded to R2, the border
gateway router.
–R2 performs the NAT process, translating the
internal private address of the host to a public,
outside address.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
25
NAT terminology
 In NAT terminology, the inside network is the set of
networks that are subject to translation. The outside
network refers to all other addresses.
–Inside local address – Usually an RFC 1918 address.
•The "inside" of a NAT configuration is not synonymous with
private addresses as defined by RFC 1918.
•In the figure, the IP address 192.168.10.10 is assigned to the
host PC1 on the inside network.
–Inside global address - Valid public address that the
inside host is given when it exits the NAT router.
•When traffic from PC1 is to the web server at 209.165.201.1,
router R2 must translate the address to 209.165.200.226.
–Outside global address - Reachable IP address assigned
to a host on the Internet.
•For example, the web server is at IP address 209.165.201.1.
–Outside local address - The local IP address assigned to
a host on the outside network.
•In most situations, this address will be identical to the outside
global address of that outside device.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
26
How Does NAT Work?
 In this example, an inside host (192.168.10.10) wants
to communicate with an outside web server
(209.165.201.1).
–It sends a packet to R2, the NAT-configured border
gateway for the network.
–R2 translates an inside local IP address to an inside
global IP address, which is 209.165.200.226.
–It stores this mapping of local to global address in the
NAT table.
–The router then sends the packet to its destination.
–When the web server responds, the packet comes back
to the global address of R2 (209.165.200.226).
–R2 translates the inside global address to the inside
local address, and the packet is forwarded to PC1 at IP
address 192.168.10.10.
–If it does not find a mapping, the packet is dropped.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
27
Dynamic Mapping and Static Mapping
 There are two types of NAT translation:
 Dynamic:
–Dynamic NAT uses a pool of public addresses and
assigns them on a first-come, first-served basis.
•When a host with a private IP address requests access to
the Internet, dynamic NAT chooses an IP address from the
pool that is not already in use by another host.
 Static:
–Static NAT uses a one-to-one mapping of local and
global addresses, and these mappings remain constant.
•Static NAT is particularly useful for servers or hosts that
must have a consistent address that is accessible from the
Internet.
•These internal hosts may be enterprise servers or
networking devices.
 Both static and dynamic NAT require that enough
public addresses are available to satisfy the total
number of simultaneous user sessions.
– ?????? (Explain)
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
28
NAT Overload
 Differences Between NAT and NAT Overload
–NAT: It generally only translates IP addresses on a 1:1 correspondence
between publicly exposed IP addresses and privately held IP addresses.
–NAT overload: It modifies both the private IP address and port number of
the sender.
•NAT overload chooses the port numbers seen by hosts on the public network.
•This is what most home routers do.
 POP QUIZ:
–Can you test of show the prove that whether your work
or school network is running NAT or NAT Overload?
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
29
NAT Overload
 NAT overloading (sometimes called Port Address
Translation or PAT) maps multiple private IP
addresses to a single public IP address or a few
addresses.
–When a client opens a TCP/IP session, the NAT router
assigns a port number to its source address.
–NAT overload ensures that clients use a different TCP
port number for each client session on the Internet.
–When a response comes back from the server, the
source port number, which becomes the destination port
number on the return trip, determines to which client the
router routes the packets.
 Port numbers are encoded in 16 bits. The total
number of internal addresses that can be translated
to one external address could theoretically be as high
as 65,536 per IP address.
–However, realistically, the number of internal addresses
that can be assigned a single IP address is around
4,000.
–-WHY???????
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
30
NAT Overload
 NAT overload attempts to preserve original port.
– In the previous example, the client port numbers in
the two SAs, 1331 and 1555, do not change at the
border gateway.
– However, if this source port is already used, NAT
overload assigns the first available port number
starting from the beginning of the appropriate port
group 0-511, 512-1023, or 1024-65535.
•When there are no more ports available and there is
more than one external IP address configured, NAT
overload moves to the next IP address to try to
allocate the original source port again.
•This process continues until it runs out of available
ports and external IP addresses.
 In the figure, both hosts have somehow chosen
the same port number 1444. However, at the
border gateway, the port numbers need to be
changed-otherwise, two packets from two hosts
would leave R2 with the same source address.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
31
PAT Example
Inside local
Inside global
NAT/PAT table maintains
translation of:
Outside global
SA (DA), DA (SA), DP (SP)
Outside local
Most of the time, PAT will try to keep the same port address. If there is a
conflict, it will alter the port number for the packet that have arrived
later.
Gateway#sh ip nat translations
Pro Inside global
Inside local
Outside local
Outside global
udp 200.2.2.18:1025 10.10.10.20:1027 10.14.4.21:161 20.14.4.21:161
udp 200.2.2.18:1027 10.10.10.10:1027 10.14.4.21:161 20.14.4.21:161
•
PAT is one-to-many relationship. One PC can potentially grab many IP addresses. If
the incoming source port is different, it will create another PAT translations.
Gateway#sh ip nat translations
Pro Inside global
Inside local
Outside local
Outside global
icmp 200.2.2.18:512 10.10.10.10:512 172.16.1.1:512 172.16.1.1:512
tcp 200.2.2.18:1166 10.10.10.20:1166 172.16.1.1:23
172.16.1.1:23
tcp 200.2.2.18:1167 10.10.10.20:1167 172.16.1.1:23
172.16.1.1:23
tcp 200.2.2.18:1168 10.10.10.20:1168 172.16.1.1:23
172.16.1.1:23
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
3 telnet sessions are
opened on the PC at
10.10.10.20
32
Benefits and Drawbacks of Using NAT
 The benefits of using NAT include the following:
–NAT conserves the legally registered addressing.
•NAT conserves addresses through port-level
multiplexing.
–NAT increases the flexibility of connections to the
public network.
•Multiple pools, backup pools, and load-balancing
pools can be implemented to ensure reliable public
network connections.
–NAT provides consistency for internal network
addressing schemes.
•An organization could change ISPs and not need to
change any of its inside clients.
–NAT provides network security.
•Private networks do not advertise their addresses or
internal topology, they remain reasonably secure
when used in conjunction with NAT to gain controlled
external access.
•However, NAT does not replace firewalls.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
33
Benefits and Drawbacks of Using NAT
 However, NAT does have some drawbacks.
–NAT affects performance.
•NAT increases switching delays because the
translation of IP headers and possibly TCP or UDP
header takes time.
–Many Internet protocols depend on unmodified
packets forwarded from the source to destination.
•Some security applications, such as digital signatures,
fail because the source IP address changes.
–End-to-end IP traceability is also lost.
•It becomes much more difficult to trace packets that
undergo numerous packet address changes over NAT.
–NAT complicates tunneling protocols
•NAT modifies values in the headers that interfere with
the integrity checks done by IPsec tunneling protocols.
–Services that require the initiation of TCP
connections from the outside can be disrupted.
•Unless the NAT support such protocols, incoming
packets cannot reach the destination.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
34
Configuring Static NAT
 Static NAT is a one-to-one mapping between an
inside address and an outside address.
–You map an inside global address to a specific
inside local address that is assigned to you.
–Unlike dynamic translations, these translations are
always in the NAT table.
 Configuring static NAT translations
1. You need to define the addresses to translate
2. Configure NAT on the appropriate interfaces.
•Packets arriving on an inside interface from the
identified IP address are subject to translation.
•Packets arriving on an outside interface addressed
to the identified IP address are subject to translation.
 The figure is a simple static NAT configuration.
–The host on the Internet directs requests to public
address 209.165.200.254, and router R2 forwards
that traffic to the server at 192.168.10.254.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
35
Configuring Dynamic NAT
 Dynamic NAT dynamically maps private IP
addresses to public addresses.
– These public IP addresses come from a NAT pool.
 Dynamic NAT configuration differs from static NAT,
– Rather than creating a static map to a single IP
address, a pool of inside global addresses is used.
 To configure dynamic NAT, you need an ACL to
permit only those addresses that are to be translated.
– Remember there is implicit "deny all" at the end of
each ACL.
– Cisco advises against configuring access control lists
referenced by NAT with permit any command.
 This configuration allows translation for all hosts on
the 192.168.10.0 and 192.168.11.0 networks when
they generate traffic that enters S0/0/0 and exits
S0/1/0.
– These hosts are translated to an available address in
the 209.165.200.226 - 209.165.200.240 range.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
36
Configuring NAT Overload for a Single Public IP Address
 There are two ways to configure overloading,
– ISP allocates one public IP address to the organization
– ISP allocates more than one public IP address.
 With only one public IP address, the overload
configuration typically assigns that public address to
the outside interface that connects to the ISP.
– All inside addresses are translated to the single IP
address when leaving the outside interface.
– The configuration is similar to dynamic NAT, except no
NAT pool is defined.
– For Example: Home DSL or cable modem connection
 In the example, all hosts from network 192.168.0.0
/16 (matching ACL 1) sending traffic through router
R2 to the Internet are translated to IP address
209.165.200.225 (interface S0/1/0 IP address).
– The traffic flows are identified by port numbers,
because the overload keyword was used.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
37
Configuring NAT Overload for a Pool of Public Addresses
 In the scenario where the ISP has provided
more than one public IP address, NAT overload
is configured to use a pool.
– The primary difference between this
configuration and the configuration for dynamic
and one-to-one NAT is that the overload
keyword is used.
– The overload keyword enables port address
translation.
 In this example, the configuration establishes
overload translation for NAT pool NAT-POOL2.
– The NAT pool contains addresses
209.165.200.226 - 209.165.200.240 and is
translated using PAT.
– Hosts in the 192.168.0.0 /16 network are subject
to translation.
– Finally, the inside and outside interfaces are
identified.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
38
Configuring Port Forwarding
 NAT does not allow requests initiated from the
outside. Port forwarding allows you to identify specific
ports that can be forwarded to inside hosts.
– Port forwarding (sometimes referred to as tunneling)
– It is the act of forwarding a network port from one
network node to another.
 The figure is displaying the Port Forwarding Example
– HTTP service requests coming into this Linksys is now
forwarded to the web server with the inside local
address of 192.168.1.254.
– If the external WAN IP address of the SOHO router is
209.165.200.158, the external user could enter
http://209.165.202.158 and the Linksys router would
redirect the HTTP request to the internal web server at
IP address 192.168.1.254, using the default port
number 80.
– We could specify a port different from the default port
80. However, the external user would have to know
the specific port number to use.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
The website
www.portforward.com
provides guides for
several broadband
routers.
39
Verifying NAT and NAT Overload
 One of the most useful commands when verifying
NAT operation is the show ip nat translations.
– Before using the show commands to verify NAT, you
must clear any dynamic translation entries that might
still be present using clear ip nat translation command.
• Only the dynamic translations are cleared from the table.
• Static translations cannot be cleared from table.
 In the figure, router R2 has been configured to
provide NAT overload to the 192.168.0.0 /16 clients.
– The show ip nat statistics command displays
• about the total number of active translations,
• NAT configuration parameters,
• how many addresses are in the pool,
• how many have been allocated.
– In the figure, the hosts have initiated web traffic as well
as ICMP traffic.
 By default, translation entries time out after 24 hours,
– unless the timers have been reconfigured with the ip
nat translation timeout timeout_ seconds command.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
40
Troubleshooting NAT and NAT Overload Configuration
 Step 1. Based on the configuration, clearly define
what NAT is supposed to achieve.
 Step 2. Verify that correct translations exist in the
translation table using the show ip nat translations.
 Step 3. Use the clear and debug commands to verify
that NAT is operating as expected.
–Check to see if dynamic entries are recreated after
they are cleared.
 Step 4. Review and verify that routers have the
correct routing information to move the packet.
–Use the debug ip nat command to verify the operation.
• * - The asterisk next to NAT indicates that the translation
is occurring in the fast-switched path.
• s= - Refers to the source IP address.
• a.b.c.d--->w.x.y.z - Indicates that source address a.b.c.d
is translated to w.x.y.z.
• d= - Refers to the destination IP address.
• [xxxx] - The value in brackets is the IP identification
number. This information may be useful for debugging
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
41
Troubleshooting NAT and NAT Overload Configuration
 Flash Animation Case Study: Can Ping Host, but Cannot Telnet: This is a
seven-minute Flash animation on why a device can ping the host, but cannot
telnet: http://www.cisco.com/warp/public/556/index.swf.
 Flash Animation Case Study: Cannot Ping Beyond NAT: This is a ten-minute
Flash animation on why a device cannot ping beyond NAT:
http://www.cisco.com/warp/public/556/TS_NATcase2/index.swf.
http://www.cisco.com/warp/public/556/TS_NATcase2
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080094c32.shtml#case2
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
42
IPv6
 IPv6, or IPng (IP – the Next Generation) uses a 128-bit address
space, yielding
340,282,366,920,938,463,463,374,607,431,768,211,456
possible addresses.
 IPv6 has been slow to arrive
 IPv4 revitalized by new features, making IPv6 a luxury, and not
a desperately needed fix
 IPv6 requires new software; IT staffs must be retrained
 IPv6 will most likely coexist with IPv4 for years to come.
 Some experts believe IPv4 will remain for more than 10 years.
http://www.cisco.com/univercd/cc/td/doc/pr
oduct/software/ios122/122newft/122t/122t2
/ipv6/ftipv6o.htm
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
43
IPv6
 Well hear it is
 2^128 =
340,282,366,920,938,463,463,374,607,431,768,211,456
 To say this number out loud just read the following.
–340 undecillion,282 decillion,366 nonillion,920 octillion,938
septillion,463 sextillion,463 quintillion,374 quadrillion,607 trillion,431
billion,768 million,211 thousand,456
 For numbers larger than that this is the order.
–vigintillion, novemdecillion ,octodecillion, septendecillion,
sexdecillion, quindecillion, quattuordecillion, tredecillion,
duodecillion, undecillion, decillion, nonillion, octillion, septillion,
sextillion, quintillion, quadrillion, trillion, billion, million, thousand,
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
44
Federal agencies must use the next-generation
Internet service known as Internet protocol version
6 (IPv6) by June 2008, the White House Office of
Management and Budget announced
http://www.whitehouse.gov/omb/memoranda/fy2005/m05-22.pdf
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
45
Reasons for Using IPv6
 IPv4 address space provides approximately
4,294,967,296 unique addresses.
–3.7 billion addresses are assignable
–January 2007, about 2.4 billion are already assigned.
–Some reports predict IPv4 address exhaustion by
2010, and others say it will not happen until 2013.
 The numbers is shrinking for the following reasons:
–Population growth - The Internet population is growing.
–Mobile users - Industry has delivered more than 20
million IP-enabled mobile devices. Old mobile phones
did not need IP addresses, but new ones do.
–Transportation - Newer models of automobile are IPenabled to allow remote monitoring to provide timely
maintenance and support.
–Consumer electronics - The newest home appliances
allow remote monitoring using IP technology. Digital
Video Recorders (DVRs) that download and update
program guides from the Internet are an example.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
46
Reasons for Using IPv6
 Movement to change from IPv4 to IPv6 has
begun, particularly in Europe, Japan, and the
Asia region.
– These areas are exhausting their IPv4
addresses, which makes IPv6 all the necessary.
 An IPv6 address is a 128-bit binary value, which
can be displayed as 32 hexadecimal digits.
– IPv6 should provide sufficient addresses for
future Internet growth needs for many years to
come.
 So what happened to IPv5?
– IPv5 was used to define an experimental realtime streaming protocol.
– To avoid any confusion, it was decided to not
use IPv5 and name the new IP protocol IPv6.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
47
Total number of allocated IPv6 prefixes
per RIR on 16/04/2007
16/04/2007
http://www.ripe.net/rs/ipv6/stats/
48
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
48
Improved features for IPv6
 IPv6 new and improved features.
1. Enhanced IP addressing
2. Simplified header
3. Mobility and security
4. Transition richness
1. Enhanced IP Addressing (Large address space):
–Improved global reachability and flexibility.
–Better aggregation of IP prefixes in routing tables.
–Multihomed hosts.
• With IPv6, a host can have multiple IP addresses over one
physical upstream link.
–Autoconfiguration that can include data link layer
addresses in the address space.
–More plug-and-play options for more devices.
–End-to-end readdressing without address translation.
• This makes P2P networking easier to deploy.
–Simplified mechanisms for address renumbering and
modification.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
49
Improved features for IPv6
2. Simple Header
–The IPv4 header has 20 octets and 12 basic
header fields, followed by an options field and a
data portion (usually the transport layer
segment).
–The IPv6 header has 40 octets, three IPv4
basic header fields, and five additional header
fields:
• Better routing efficiency
• No broadcasts and no threat of broadcast
storms
• No requirement for processing checksums
• More efficient extension header mechanisms
• Flow labels for per-flow processing with no need
to open the transport inner packet to identify the
traffic flows
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
50
Improved features for IPv6
3. Enhanced Mobility and Security
– Mobile IP: Mobile devices use a home address and a
care-of address to achieve this mobility. With IPv4, these
addresses are manually configured. With IPv6, the
configurations are dynamic.
– IP Security (IPsec): IPsec is available for both IPv4 and
IPv6. IPsec is mandatory in IPv6.
4. Transition Richness
–IPv4 will not disappear overnight.
–Currently, there are three migration techniques:
• Dual stack
– Configure with both IPv4 and IPv6 on the interface.
• 6to4 tunneling
– uses an IPv4 tunnel to carry IPv6 traffic
• NAT-PT, ISATAP tunneling, and Teredo tunneling (last resort
methods)
– This translation allows direct communication between
hosts speaking different protocols.
–The current advice for transitioning to IPv6 is "Dual stack
where you can, tunnel where you must!"
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
51
IPv6 Address Representation
 IPv6 addresses use colons to separate entries in a
series of 16-bit hexadecimal.
 2031:0000:130F:0000:0000:09C0:876A:130B. The
figure shows how to shorten the address:
–Leading zeros in a field are optional.
•The field 09C0 equals 9C0, and the field 0000 equals 0.
2031:0000:130F:0000:0000:09C0:876A:130B becomes
2031:
0:130F:
0:
0: 9C0:876A:130B
–Successive fields of zeros can be represented as two
colons "::".
•However, this shorthand method can only be used
once in an address.
2031:0:130F:0000:0000: 9C0:876A:130B becomes
2031:0:130F
::
9C0:876A:130B
–An unspecified address is written as "::" because it
contains only zeros.
0:0:0:0:0:0:0:0 becomes
::
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
52
IPv6 Addressing
 IPv6 Global Unicast Address
–Global unicast addresses typically consists of a 48-bit global routing prefix and a
16-bit subnet ID (for example: 2001:db8:1234::/48 )
•Individual organizations can use a 16-bit subnet field to create their own local
addressing hierarchy. This allows an organization to use up to 65,535
subnets.
–The current global unicast address that is assigned by the IANA uses the range of
addresses that start with binary value 001 (2000::/3), which is 1/8 of the total IPv6
address space and is the largest block of assigned addresses.
–The IANA is allocating the IPv6 address space in the ranges of 2001::/16 to the
five RIR registries (ARIN, RIPE NCC, APNIC, LACNIC, and AfriNIC).
2000:: /3
001X
RFC 4291:
IP Version 6 Addressing
Architecture
128 – 3 = 125 bits
=> 4.25352959 × 1037
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
53
IPv6 Addressing
 Reserved Addresses
–Reserved addresses represent 1/256th of the total IPv6
address space.
 Private Addresses
–A block of IPv6 addresses is set aside for private
addresses, just as is done in IPv4.
–Private addresses have a first octet value of "FE".
•Site-local addresses, are addresses similar to the RFC
1918 Address Allocation for Private Internets in IPv4 today.
– They begin with “1111 1110 11”.
– In hexadecimal, site-local addresses begin with "FE" and then
"C" to "F" for the third hexadecimal digit. So, these addresses
begin with "FEC", "FED", "FEE", or "FEF".
•Link-local addresses, are new to the concept of
addressing with IP in the Network layer.
– They begin with “1111 1110 1”.
– Routers do not forward datagrams using link-local addresses at
all, not even within the organization.
– They are used for link communications such as automatic
address configuration, neighbor discovery, and router discovery.
– Link-local addresses begin with "FE" and then have a value
from "8" to "B" for the third hexadecimal digit. So, these
addresses start with "FE8", "FE9", "FEA", or "FEB".
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
54
IPv6 Addressing
 Loopback Address
–In IPv6 there is just one address, not a whole block, for this function.
–The loopback address is 0:0:0:0:0:0:0:1, which is normally expressed using
zero compression as "::1".
 Unspecified Address
–In IPv4, an IP address of all zeroes has a special meaning; it refers to the host
itself, and is used when a device does not know its own address.
–In IPv6, this concept has been formalized, and the all-zeroes address
(0:0:0:0:0:0:0:0) is named the "unspecified" address. It is typically used in the
source field of a datagram that is sent by a device that seeks to have its IP
address configured.
–You can apply address compression to this address; because the address is
all zeroes, the address becomes just "::".
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
55
Configuring Windows XP
56
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
56
Configuring Windows XP
57
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
57
Configuring Windows XP
 No ipv6
• Add ipv6
IPv6 for Microsoft Windows: Frequently Asked Questions
http://www.microsoft.com/technet/network/ipv6/ipv6faq.mspx
58
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
58
Configuring Windows XP
Also see RFC 4007
 Zone IDs for Local-Use IPv6 Addresses
– Unlike global addresses, link-local and site-local address
prefixes can be reused. Because of this address prefix
reuse capability, link-local and site-local addresses are
ambiguous.
– To specify which link on which a link-local address is
assigned or located or within which site a site-local
address is assigned or located, IPv6 uses an additional
identifier known as a zone identifier (ID) (also known as a
scope ID).
– The syntax specified in RFC 4007 for identifying the zone
associated with a local-use address is the following:
•Address%zone_ID
– Address is a local-use address and zone_ID is an integer
value representing the zone. The values of the zone ID
are defined relative to the host. Therefore, different hosts
might determine different zone ID values for the same
physical zone. For example, Host A might choose 3 to
represent the zone of an attached link and host B might
choose 4 to represent the same link.
netsh interface ipv6 show interface  For Windows-based IPv6 hosts, the zone IDs for
local-use addresses are defined as follows:
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
– For link-local addresses, the zone ID is typically the
interface index of the interface either assigned the
address or to be used as the sending interface for a linklocal destination. The interface index is an integer starting
at 1 that is assigned to IPv6 interfaces, which include a
loopback and one or multiple tunnel or LAN interfaces.
– You can view the list of interface indexes from the display
of the netsh interface ipv6 show interface command. 59
Configuring Windows XP
Ping yourself and your own loopback
Ping your neighbor and you have to
use the zone ID as part of address
60
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
60
Configuring Windows XP
netsh interface ipv6 show address
netsh interface ipv6 show interface
61
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
61
IPv6 Address Management
 IPv6 addresses use interface identifiers to identify
interfaces on a link.
–Think of them as the host portion of an IPv6 address.
–Interface identifiers are always 64 bits and can be
dynamically derived from a Layer 2 address (MAC).
• The EUI-64 standard explains how to stretch IEEE 802 MAC
addresses from 48 to 64 bits by inserting the 16-bit 0xFFFE
in the middle at the 24th bit of the MAC address to create a
64-bit, unique interface identifier.
 IPv6 address can be assigned statically or dynamically:
–Static assignment using a manual interface ID
•
RouterX(config-if)#ipv6 address 2001:DB8:2222:7272::72/64
–Static assignment using an EUI-64 interface ID
•
RouterX(config-if)#ipv6 address 2001:DB8:2222:7272::/64 eui-64
–Stateless autoconfiguration
•
Autoconfiguration automatically configures the IPv6 address.
–DHCP for IPv6 (DHCPv6) (Stateful)
–It offers the capability of automatic allocation of reusable network addresses
and additional configuration flexibility.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
62
IPv6 Transition Strategies
 Many mechanisms enable integration of IPv4 and IPv6.
–"Dual stack where you can, tunnel where you must."
 Dual Stacking
–Dual stacking is an integration method in which a node
has connectivity to both an IPv4 and IPv6 network.
 Tunneling
–Manual IPv6-over-IPv4 tunneling - An IPv6 packet is
encapsulated within the IPv4 protocol. This method
requires dual-stack routers.
–Dynamic 6to4 tunneling - Automatically establishes the
connection of IPv6 islands through an IPv4 network
–Intra-Site Automatic Tunnel Addressing Protocol
(ISATAP) tunneling - ISATAP tunnels allow individual IPv4
or IPv6 dual-stack hosts to communicate with other hosts.
–Teredo tunneling - An IPv6 transition that provides hostto-host automatic tunneling instead of gateway tunneling.
 NAT-Protocol Translation (NAT-PT)
–This translation allows direct communication between
hosts that use different versions of the IP protocol.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
63
Cisco IOS Dual Stack
 Dual stacking is an integration method that allows a
node to have connectivity to an IPv4 and IPv6
network simultaneously.
– As soon as you configure basic IPv4 and IPv6 on the
interface, the interface is dual-stacked and forwards
IPv4 and IPv6 traffic on that interface.
– Cisco IOS Release 12.2(2)T and later (with the
appropriate feature set) are IPv6-ready.
– Using IPv6 requires that you use the global
configuration command ipv6 unicast-routing. This
command enables the forwarding of IPv6 datagrams.
– You must configure all interfaces that forward IPv6
traffic with an IPv6 address using the ipv6
addressIPv6-address [/prefix length] interface
command.
 A dual-stack node chooses which stack to use based
on the destination address of the packet.
– A dual-stack node should prefer IPv6 when it is
available.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
64
IPv6 Tunneling
 Tunneling is an integration method where an
IPv6 packet is encapsulated within another
protocol, such as IPv4.
– This method enables the connection of IPv6
islands without needing to convert the
intermediary networks to IPv6.
– When IPv4 is used to encapsulate IPv6, a
protocol type of 41 is specified in IPv4 header
– It also requires dual-stack routers.
 Tunneling presents these two issues.
– The MTU is effectively decreased by 20 octets.
– A tunneled network is often difficult to
troubleshoot.
 Tunneling is an intermediate integration and
should not be considered as a final solution.
– A native IPv6 architecture should be the ultimate
goal.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
65
Manually Configured IPv6 Tunnel
 A manually configured tunnel is
equivalent to a permanent link between
two IPv6 domains over an IPv4
backbone.
– Administrators manually configure a static
IPv6 address on a tunnel interface, and
assign manually configured static IPv4
addresses to the tunnel source and the
tunnel destination.
– The host or router at each end of a
configured tunnel must support both the
IPv4 and IPv6 protocol stacks.
– Manually configured tunnels can be
configured between border routers or
between a border router and a host.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
66
Routing Considerations with IPv6
 Like IPv4 CIDR, IPv6 uses longest prefix match
routing.
–ISP aggregates all of the prefixes of its customers into
a single prefix and announces the single prefix to the
IPv6 Internet.
 But how does IPv6 affect router performance?
Conceptually, a router has three functional areas:
–The control plane handles the interaction of the router
with the other network elements, providing the
information needed to make decisions and control the
overall router operation.
• This plane runs processes such as routing protocols and
network management.
–The data plane handles packet forwarding from one
physical or logical interface to another.
• It involves different switching mechanisms such as
process switching and Cisco Express Forwarding (CEF).
–Enhanced services include advanced features applied
when forwarding data, such as packet filtering, quality of
service (QoS), encryption, translation, and accounting.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
http://www.cisco.com/en/US/prod/collateral/io
sswrel/ps6537/ps6586/ps6642/prod_white_p
aper0900aecd804fa16a.html
1. Data Plane
2. Management Plane
3. Control Plane
4. Services Plane
67
Routing Considerations with IPv6 Control Plane
 IPv6 Control Plane:
–IPv6 address size - Address size affects the informationprocessing functions of a router.
• Systems using a 64-bit bus can pass both IPv4 source and
destination address in a single processing cycle.
• For IPv6, the source and destination addresses require two
cycles each-four cycles to process source and destination
address information.
• As a result, routers perform slower than when in an IPv4
environment.
–Multiple IPv6 node addresses - Because IPv6 nodes can
use several IPv6 unicast addresses, memory consumption
of the Neighbor Discovery cache may be affected.
–IPv6 routing protocols - IPv6 prefix is 4 times larger than
IPv4, routing updates have to carry more information.
–Routing table Size -Increased IPv6 address space leads
to larger networks and a much larger Internet.
• This implies larger routing tables and higher memory
requirements to support them.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
68
Routing Considerations with IPv6 Data Plane
 IPv6 Data Plane:
–Parsing IPv6 extension headers - Applications, including
mobile IPv6, often use IPv6 address information in
extension headers, thus increasing their size.
• These additional fields require additional processing.
• For example, a router using ACLs to filter Layer 4
information needs to apply the ACLs to packets with
extension headers as well as those without. If the length of
the extension header exceeds the fixed length of the
hardware register of the router, hardware switching fails,
and packets may be punted to software switching or
dropped.
• This severely affects the forwarding performance of the
router.
–IPv6 address lookup - In IPv4, the forwarding decision
process parses a 32-bit destination address. In IPv6, the
forwarding decision require parsing a 128-bit address.
• Most routers today perform lookups using an applicationspecific integrated circuit (ASIC) with a fixed configuration
that performs the functions for which it was originally
designed - IPv4.
• Again, this could result in punting packets into slower
software processing, or dropping them all together.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
69
Routing Consideration with IPv6: RIPNg
 RIPNg Routing Protocol
–RFC 2080 defines Routing Information Protocol next
generation (RIPng) based on RIP.
–RIPng provides a simple way to bring up an IPv6
network without having to build a new routing protocol.
 RIPng includes the following features:
–Based on IPv4 RIPv2 and is similar to RIPv2
• It is a distance vector routing protocol
• a limit of 15 hops
• uses split horizon and poison reverse updates to prevent
routing loops.
–Uses IPv6 for transport
–Includes the IPv6 prefix and next-hop IPv6 address
–Uses the multicast group FF02::9 as the destination
address for RIP updates
–Sends updates on UDP port 521
–Is supported by Cisco IOS Release 12.2(2)T and later
 In dual-stacked deployments, both RIP and RIPng
are required.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
70
Enabling IPv6 on Cisco Routers
 There are two basic steps to activate IPv6 on a router.
– First, you must activate IPv6 traffic-forwarding on the router,
• By default, IPv6 traffic-forwarding is disabled on a Cisco router.
• To activate it between interfaces, you must configure the global
command ipv6 unicast-routing.
– Second, you must configure each interface that requires IPv6.
• The ipv6 address command can configure a global IPv6 address.
• The link-local address is automatically configured when an address
is assigned to the interface.
• You must specify the entire 128-bit IPv6 address or specify to use
the 64-bit prefix by using the eui-64 option.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
71
IPv6 Address Configuration Example
 You can completely specify the IPv6
address or compute the host identifier
(rightmost 64 bits) from the EUI-64
identifier of the interface.
– In the example, the IPv6 address of the
interface is configured using the EUI-64
format.
– Alternatively, you can completely specify
the entire IPv6 address to assign a router
interface an address using the ipv6
address ipv6-address/prefix-length
command in interface configuration
mode.
 Configuring an IPv6 address on an
interface automatically configures the
link-local address for that interface.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
Insert FFFE into
MAC address to
make up EUI-64
72
Cisco IOS IPv6 Name Resolution
 There are two ways to perform name resolution from the Cisco IOS
software process:
–Define a static name for an IPv6 address using the ipv6 host name [port]
ipv6-address1 [ipv6-address2...ipv6-address4] command.
• You can define up to four IPv6 addresses for one hostname.
• The port option refers to the Telnet port to be used for the associated host.
–Specify the DNS server used by the router with the ip name-server address
command.
• The address can be an IPv4 or IPv6 address. You can specify up to six DNS
servers with this command.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
73
Configure RIPng with IPv6
 Before configuring the router to run IPv6 RIP, globally enable IPv6 using
the ipv6 unicast-routing global configuration command, and enable
IPv6 on any interfaces on which IPv6 RIP is to be enabled.
 To enable RIPng routing on the router,
– use the ipv6 router rip name global configuration command.
• The name parameter identifies the RIP process.
• This process name is used later when configuring RIPng on participating
interfaces.
– For RIPng, instead of using the network command to identify which
interfaces should run RIPng, you use the command ipv6 rip name enable
in interface configuration mode to enable RIPng on an interface.
ITE 1 Chapter 6
•
The name parameter must match the name parameter in the ipv6 router rip
command.
•
Enabling RIP on an interface dynamically creates a "router rip" process if
necessary.
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
74
Example: RIPng for IPv6 Configuration
 The example shows a
network of two routers.
–Router R1 is connected to the
default network.
–On both router R2 and router
R1, the name RT0 identifies
the RIPng process.
–RIPng is enabled on the first
Ethernet interface of router R1
using the ipv6 rip RT0 enable
command.
–Router R2 shows that RIPng
is enabled on both Ethernet
interfaces using the ipv6 rip
RT0 enable command.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
75
Verifying Troubleshooting RIPng for IPv6
 After configuring RIPng,
verification is required.
 If you discover during
verification that RIPng is not
working properly, you need to
troubleshoot.
 The figure lists the
commands used to
troubleshoot RIPng problems.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
76
Chapter Summary
 In this chapter, you have learned to:
–Configure DHCP in an Enterprise branch network. This includes
being able to explain DHCP features and benefits, the differences
between BOOTP and DHCP,
DHCP
and configuring,
Tony
Chen operation:
COD
verifying, and troubleshooting DHCP.
Cisco Networking Academy
–Configure NAT on a Cisco router. This includes explaining key
features and operation of NAT and NAT Overload, explaining
advantages and disadvantages of NAT, configuring NAT and NAT
Overload to conserve IP address space in a network, configuring
port forwarding, and verifying and troubleshooting NAT
configurations.
–Configure new generation RIP (RIPng) to use IPv6. This includes
explaining how IPv6 solves any problem of IP address deletion,
explaining how to assign IPv6 addresses, describing transition
strategies for implementing IPv6 and configuring, verifying and
troubleshooting RIPng for IPv6.
ITE 1 Chapter 6
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Public
77