Download trunk - Victoria College

Switching Basics and Intermediate
Routing CCNA 3
Chapter 9
www.ciscopress.com
VLAN Trunking Protocol
Introduction
• Early VLANs were difficult to implement
across networks
– Each VLAN was manually configured on each
switch
– Each manufacturer had different VLAN
capability methods
• To solve these problems, VLAN trunking
was developed
www.ciscopress.com
VLAN Trunking Protocol
Introduction
• Trunking allows many VLANs to be identified
throughout an organization by adding tags to
frames
– The tags identify the VLANs to which the frames
belong
– Frames from many VLANs can be carried on a
common trunk
– VLAN trunking is widely implemented with the IEEE
802.1Q trunking protocol
– Inter-Switch Link (ISL) is a Cisco-proprietary protocol
that can be implemented in Cisco networks
www.ciscopress.com
VLAN Trunking Protocol
Introduction
• Cisco created VLAN Trunking Protocol (VTP)
– Automates many VLAN configuration tasks
– Configurations on a VTP server are automatically
propagated to other switches in the VTP domain
• VLAN technology offers advantages:
– Helps control Layer 3 broadcasts, improve network
security, logically group network users
• VLAN limitations:
– Operate at Layer 2; cannot communicate without use
of routers (or Layer 3 switches) and network layer
addresses
www.ciscopress.com
Trunking
Introduction
• Trunking goes back to the origin of radio and
telephone switching technologies
– In radio, a trunk is a single line that carries multiple
channels of radio signals
– In the telephone industry, a trunk is the
communication path or channel between two points
•
•
•
•
Can carry simultaneous, multiple lines of communication
Central Offices (CO) are connected by trunks
Shared trunks are created for redundancy
Multiplexers combine several voice signals into a single trunk
line and demultiplex the signal at the other end
www.ciscopress.com
Trunking
Introduction
Traditional Telephone Trunk Line Carries
Multiple Simultaneous Conversations
www.ciscopress.com
Trunking
Introduction
Shared Telephone Trunks Between COs
Provide Redundancy
www.ciscopress.com
Trunking
Introduction
• The concept used by radio and telephone
industries was adopted by data communications
– A backbone link between a main distribution facility
(MDF) and an intermediate distribution facility is
composed of several trunks
• The same concept is applied to switching
technologies
– A trunk is a physical and logical connection between
two switches
– Network traffic travels across the trunk
– A trunk is a single transmission channel between two
points (a point-to-point link)
www.ciscopress.com
Trunking
Introduction
VLAN Trunking
www.ciscopress.com
Trunking
VLAN Trunking Operation
• Switching tables at both ends of the trunk are
used to make forwarding decisions based on
destination MAC addresses of the frames
– As number of VLANs increases, this process
becomes slower
– Larger switching tables take longer to process
• Trunking protocols were developed to efficiently
manage the transfer of frames from different
VLANs on a single physical line
www.ciscopress.com
Trunking
VLAN Trunking Operation
• Modern trunking protocols use frame tagging
– Faster delivery of frames
– Easier management
• The single physical link between two switches
can carry frames for multiple VLANs
– Each frame is tagged to identify the VLAN to which it
belongs
– Different tagging schemes exist
• Cisco’s ISL
• IEEE 802.1Q
– The tag is removed when the frame leaves the trunk
www.ciscopress.com
Trunking
VLAN Trunking Operation
ISL Trunking
www.ciscopress.com
Trunking
VLAN Trunking Operation
• With ISL, an Ethernet frame is encapsulated with
an additional header that contains a VLAN ID
• With IEEE 802.1Q, a tag containing the VLAN ID
is embedded in the Ethernet Frame
• A trunk link does not belong to a specific VLAN
– It is a conduit for VLANs between switches
and routers
www.ciscopress.com
Trunking
VLAN Trunking Operation
VLAN Trunking Multiplexing Data from Multiple
VLANs onto a Single Link
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
• The IEEE 802.1Q protocol:
– Interconnects multiple switches and routers
– Defines VLAN topologies
– Cisco supports IEEE 802.1Q for FastEthernet
and Gigabit Ethernet interfaces
– Can carry traffic for multiple VLANs over a
single link on a multivendor network
– Extends IP routing capabilities to include
support for IP frame types
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
• The two ports on the ends of an IEEE
802.1Q trunk are assigned to a native
VLAN
– (VLAN 1 by default)
– Can be assigned to another VLAN
– All untagged frames are assigned to the
native VLAN
• Ordinary end stations are able to read the
untagged frames but not the tagged frames
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
IEEE 802.1Q Trunking
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
Frames Associated with the Native VLAN Are
Untagged and Are Readable by End Stations
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
• Adding a frame tag results in the recomputation
of the frame check sequence (FCS)
– Embedded tag increases the size of the Ethernet
frame
Recomputation of the FCS
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
• The IEEE 802.1Q standard defines a
unique spanning-tree instance running on
the native VLAN for all the network VLANs
– An 802.1Q mono spanning tree (MST) lacks
some flexibility compared with a per-VLAN
spanning tree + (PVST+) that runs one
instance of Spanning Tree Protocol (STP) per
VLAN
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
• A mono spanning tree has only one
instance of spanning tree for all VLANs
• Per-VLAN spanning tree (PVST) maintains
a spanning tree instance for each VLAN
– Uses ISL trunking
– Cisco developed PVST+ to enable running of
several STP instances and to allow
connection of an MST zone to a PVST zone
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
Cisco PVST+ Interoperates with Other
Vendors’ STP Implementations
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
• PVST+ provides support for 802.1Q trunks and
the mapping of multiple spanning trees to the
single spanning tree of 802.1Q switches
– Must be in a treelike structure for proper STP
operation
• PVST+ architecture has three types of regions:
– PVST region
– PVST+ region
– MST region
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
• Each region consists of a homogenous switch
– Can connect a PVST region to a PVST+ region by
connecting two ISL ports
– Can connect a PVST+ region to an MST region by
connecting two 802.1Q ports
• The existing Cisco STP implementation was
extended to become PVST+
– Added support for tunneling across an IEEE 802.1Q
MST region
• Tunneling means that BPDUs are flooded through the MST
region along the single spanning tree in the MST region
• PVST+ is thus compatible with 802.1Q and PVST
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
– The existing Cisco STP implementation was extended
to become PVST+ (continued)
• PVST+ adds verification mechanisms to ensure consistent
port configuration and needs no additional configuration
commands
• IEEE 802.1Q trunks impose some limitations on
trunking strategy for a network:
– The native VLAN on for an 802.1Q trunk must be the
same on both ends of the link
– The network must be loop-free before STP is disabled
www.ciscopress.com
Trunking
IEEE 802.1Q Trunking
Interaction Between 802.1Q Features and
Trunk Ports
www.ciscopress.com
ISL Trunking
Introduction
• ISL characteristics and features:
– Cisco proprietary
– Interconnects multiple switches and maintains
VLAN information as traffic travels between
switches
– Full wire-speed performance over
FastEthernet
– Full- or half-duplex mode
• Full-duplex recommended
– Operates in a point-to point environment
www.ciscopress.com
ISL Trunking
Introduction
• ISL characteristics and features
(continued):
– Uses frame tagging that is a low-latency
mechanism for multiplexing traffic from
multiple VLANs on a single physical
path
– Implemented for connections among
switches, routers, and NICs that are
used on nodes such as servers
www.ciscopress.com
ISL Trunking
Introduction
• To support ISL, each device must be
ISL configured
– An ISL-configured router allows interVLAN communication
– Non-ISL devices that receive ISL frames
might consider them to be errors as the
size of the frame exceeds the maximum
transmission unit (MTU) size
• MTU for Ethernet is 1500 bytes
www.ciscopress.com
ISL Trunking
Introduction
• ISL functions at Layer 2
– Encapsulates a data frame with a new header
and a cyclic redundancy check (CRC)
• ISL is protocol independent for any type of
upper-layer protocol
– Used to maintain redundant links and load
balance traffic between parallel links using
STP
www.ciscopress.com
ISL Trunking
Introduction
• Ports configured as ISL trunk ports
encapsulate each frame with a 26-byte ISL
header and a 4-byte CRC before sending
it out the trunk port
– ISL is implemented in ASICs, so frames are
tagged at wire-speed
• The number of VLANs supported by a
switch depends on the switch hardware
www.ciscopress.com
ISL Trunking
Introduction
ISL Header and CRC Added to Ethernet
Frames on ISL Trunks
www.ciscopress.com
ISL Trunking
Introduction
• Information in the ISL header:
– DA: 40-bit multicast destination address
– Type: 4-bit descriptor of the encapsulated
frame type
– User: 4-bit descriptor used as the type field
extension or to define the Ethernet priorities
– SA: 48-bit source MAC address of the
transmitting Catalyst switch
– LEN: 16-bit frame-length descriptor minus
DA, Type, User, SA, LEN, and CRC
www.ciscopress.com
ISL Trunking
Introduction
• Information in the ISL header (continued):
– AAAA03: standard Subnetwork Access Protocol
(SNAP) 802.2 LLC header
– HSA: first three bytes of the SA (OUI)
– VLAN ID: 15-bit VLAN ID
– BPDU: 1-bit descriptor that identifies whether the
frame is a spanning-tree BPDU
– INDX: 16-bit descriptor that identifies transmitting
port ID
– RES: 16-bit field used for additional information, such
as FDDI frame control
www.ciscopress.com
ISL Trunking
Configuring VLAN Trunking - Introduction
• Becoming less common to use ISL
• More common to use IEEE 802.1Q
– Older Catalyst switches support both
– Some newer models support both, some
support only 802.1Q (Catalyst 2950)
www.ciscopress.com
ISL Trunking
Configuring VLAN Trunking
802.1Q Trunk Configuration
• On a Catalyst 2950 switch, 802.1Q is configured
automatically when trunking is enabled on the
interface
– Use the switchport mode trunk command
• The switchport mode command has four
options:
– trunk – configures the port into permanent 802.1Q
mode
– access – disables trunk mode and negotiates with
the connected device to covert the link to nontrunk
www.ciscopress.com
ISL Trunking
Configuring VLAN Trunking
802.1Q Trunk Configuration
• The switchport mode command has four
options (continued):
– dynamic desirable – triggers the port to
negotiate from nontrunk to trunk mode
– dynamic auto – enables a port to become a
trunk only if the connected device has the
state set to trunk or desirable; otherwise the
port becomes a nontrunk port
www.ciscopress.com
ISL Trunking
Configuring VLAN Trunking
802.1Q Trunk Configuration
• The switchport nonnegotiate command
(Catalyst 2950) specifies that Dynamic
Trunking Protocol (DTP) negotiation
packets not be sent on Layer 2 interfaces
– Switch does not engage in DTP negotiation
on this interface
– Command valid only when the interface
access mode is access or trunk
www.ciscopress.com
ISL Trunking
Configuring VLAN Trunking
802.1Q Trunk Configuration
Steps to Configure a Switch Port as a Trunk Port
www.ciscopress.com
ISL Trunking
Configuring VLAN Trunking
ISL Trunk Configuration
• For Catalyst switches supporting ISL
– Use the switchport trunk encapsulation
interface command
– Encapsulation types:
• dot1q: uses only 802.1Q trunking encapsulation
• isl: uses only ISL trunking encapsulation with a
peer on the interface
• negotiate: device negotiates trunking
encapsulation with peer on the interface
www.ciscopress.com
ISL Trunking
Configuring VLAN Trunking
ISL Trunk Configuration
Configuring ISL Trunking
www.ciscopress.com
VTP
Introduction
• Cisco created the proprietary VLAN Trunking Protocol
(VTP) to solve operational problems in switched
networks with VLANs
– A domain may consist of several interconnected
switches supporting multiple VLANs
– To maintain connectivity within the VLANs, each
VLAN must be manually configured on a switch
– As additional switches are added to the network, they
must be manually configured
– A single incorrect configuration can cause crossconnected VLANs
• VTP reduces management and monitoring complexities
www.ciscopress.com
VTP
VTP Concepts
• VTP concepts and characteristics:
– VTP is a Layer 2 messaging protocol
– Maintains VLAN consistency by managing the
addition, deletion, and name changes of VLANs
across networks
– Minimizes misconfigurations that can cause problems
• A VTP domain is an administrative unit
consisting of one switch or several
interconnected switches
– A switch can be configured in only one VLAN domain
www.ciscopress.com
VTP
VTP Concepts
VTP Domain
www.ciscopress.com
VTP
VTP Concepts
• By default, a Catalyst switch is in the nomanagement-domain state until it receives
an advertisement over a trunk link or until
a management domain is configured
– Configurations are made to a single VTP
server
• A Catalyst switch on which configuration changes
are propagated across links to all connected
switches in the domain
• VTP advertisements are sent on trunk ports only
www.ciscopress.com
VTP
VTP Operations
• VTP operates in one of three modes:
– Server mode (default mode)
• VLANs are not propagated until a management
domain name is specified or learned
• When a VLAN is created, modified, or deleted, the
change is propagated to all switches in the VTP
domain
• VTP advertisements are transmitted out all trunk
connections and synchronized with other VTP
servers and clients
• VTP information is saved in NVRAM
www.ciscopress.com
VTP
VTP Operations
• VTP operates in one of three modes
(continued):
– Transparent mode
• When in transparent mode, VLAN creation, modification, or
deletion affects only the local switch and is not propagated
to other switches
• VLAN information is saved in NVRAM
– Client mode
• Cannot create, modify, or delete VLANs when in client mode
• VTP advertisements are forwarded when in client mode
• VTP information is synchronized with other VTP clients and
servers
• VLAN information is saved in NVRAM
www.ciscopress.com
VTP
VTP Operations
• VLAN advertisements are flooded
throughout the management domain
– Sent every 5 minutes or when a change
occurs
– Transmitted over the default VLAN (VLAN 1)
using a multicast frame
– Revision numbers are used; a higher revision
number indicates more current information
www.ciscopress.com
VTP
VTP Operations
• A critical component of VTP is the configuration
revision number
– Each time information is changed, the VTP
increments the configuration revision number by one
– The server then sends out a VTP advertisement with
the new configuration revision number
– If this number is higher than the number stored on a
switch, the switch overwrites its configuration
information with the new information
– The configuration revision number in transparent
mode is always 0
www.ciscopress.com
VTP
VTP Operations
VTP Messages Synchronizing VLAN Information
Within a VTP (Management) Domain
www.ciscopress.com
VTP
VTP Operations
• A device receiving VTP advertisements
must:
– Check that the management domain name
and password match that on the local switch
– Check that the configuration revision number
was created after the configuration currently
in use
• To reset the revision number, use the
delete vtp privileged EXEC command
www.ciscopress.com
VTP
VTP Operations
• VTP Pruning uses VLAN advertisements to determine
when a trunk is needlessly flooding traffic
– VTP pruning results in prevention of unnecessary traffic
– VTP pruning increases bandwidth by restricting traffic
to those trunk links that the traffic must use to access
appropriate devices
• By default, a trunk carries traffic for all VLANs in the VTP
management domain
– Some switches will not have ports configured in each
VLAN
• VTP pruning is enabled on servers, not clients; if VTP is
not deployed must set switches to transparent mode
www.ciscopress.com
VTP
VTP Operations
VTP Pruning Preventing Unnecessary VLAN
Traffic in a VTP Domain
www.ciscopress.com
VTP
Configuring VTP
• When creating VLANs, must decide
whether to use VTP in the network
– Allows configuration changes made on one
switch to be propagated to all other switches in
the VTP domain
– Default values for a Catalyst 2950 switch:
• VTP domain name: none, VTP mode: server, VTP
password: none, VTP pruning: disabled, VTP
version: 1, VTP trap: disabled
www.ciscopress.com
VTP
Configuring VTP
• VTP domain name can be configured or learned
– Not set by default
• An optional password can be set for the VTP
management domain
– Must be the same password for each switch in
the domain
• Enabling or disabling VTP pruning on a server
propagates the change throughout the
management domain
www.ciscopress.com
VTP
Configuring VTP
• The vtp global configuration command is
used to modify VTP configuration:
– vtp {domain domain-name | file filename |
interface name | mode {client | server |
transparent} | password password | pruning |
version number}
• When the VTP mode is transparent, the
VTP configuration can be saved to the
switch with the copy running-config
startup-config command
www.ciscopress.com
VTP
Configuring VTP
• With the Catalyst 2950, can use the vtp
privileged EXEC command to configure
VTP password, pruning and administrative
version:
– Switch#vtp {password password | pruning |
version number}
• Domain name and password are case
sensitive
– Domain name cannot be removed after it is
assigned; can only be reassigned
www.ciscopress.com
VTP
Configuring VTP
Configuring VTP
www.ciscopress.com
Inter-VLAN Routing Overview
Introduction
• Inter-VLAN communication occurs between
broadcast domains through a Layer 3
device
– Frames are switched only between ports in the same
broadcast domain
– VLANs perform network partitioning and traffic
separation at Layer 2
– Inter-VLAN communication cannot occur without a
Layer 3 device
– Inter-VLAN routing is routing between VLANs on a
router or a Layer 3 switch
www.ciscopress.com
Inter-VLAN Routing Overview
Router-on-a-Stick
• The configuration between a router and a
core switch is sometimes referred to as a
router-on-a-stick
– Router can receive packets on one VLAN and forward
them to another VLAN
– Must be a separate logical connection on the router for
each VLAN
– Must enable ISL or 802.1Q trunking on a single
physical connection
• Must subdivide the physical FastEthernet interface of the router
into multiple logical, addressable interfaces, one per VLAN
• These are called “subinterfaces”
www.ciscopress.com
Inter-VLAN Routing Overview
Router-on-a-Stick
Router-on-a-Stick Employing a Layer 2
Switch Trunked to a Router
www.ciscopress.com
Inter-VLAN Routing Overview
Router-on-a-Stick
Logical Subinterfaces on the Router End of a
Trunk Link in a Router-on-a-Stick Topology
www.ciscopress.com
Inter-VLAN Routing Overview
Configuring Inter-VLAN Routing
• An interface can be logically divided
into multiple virtual subinterfaces
• To define subinterfaces of a physical
interface:
– Identify the interface
– Define the VLAN encapsulation
– Assign an IP address to the interface
www.ciscopress.com
Inter-VLAN Routing Overview
Configuring Inter-VLAN Routing
One Router with Three Subinterfaces Corresponding to
Three VLANs in the Router-on-a-Stick Topology
www.ciscopress.com
Inter-VLAN Routing Overview
Configuring Inter-VLAN Routing
• To identify the interface, use the interface
command in global configuration mode
Router(config)#interface fastethernet portnumber subinterface-number
– port-number identifies the physical interface
and subinterface-number identifies the virtual
interface
www.ciscopress.com
Inter-VLAN Routing Overview
Configuring Inter-VLAN Routing
A FastEthernet Interface Can Be Subdivided into Logical
Subinterfaces Associated in a One-to-One Fashion with VLANs
www.ciscopress.com
Inter-VLAN Routing Overview
Configuring Inter-VLAN Routing
• To define the VLAN encapsulation, use the
appropriate encapsulation command in
interface configuration mode
Router(config-if)#encapsulation isl vlan-id
Router(config-if)#encapsulation dot1q vlan-id [native]
• To assign an IP address to the interface,
use the following interface mode
command:
Router(config-if)#ip address ip-address subnet mask
www.ciscopress.com
Inter-VLAN Routing Overview
Configuring Inter-VLAN Routing
Configuring Inter-VLAN Routing
www.ciscopress.com
Summary
• A trunk is a physical and logical connection
between two switches across which network
traffic travels
– Concept goes back to origins of radio and telephone
switching technology
– In LAN switching, a trunk is a point-to-point link that
supports several VLANS
– Purpose is to conserve ports when creating a link
between two devices implementing VLANs
– Multiple virtual links are bundled over one physical
link
www.ciscopress.com
Summary
• Trunking protocols were developed to efficiently
manage the transfer of frames from different
VLANs on a single physical link
– Trunking protocols establish agreement for the
distribution of frames to both ends of the link
– Trunking protocols use frame tagging to assign an
identifier to frames
• Functions at Layer 2
• Cisco’s ISL and IEEE 802.1Q are the most common tagging
schemes for Ethernet segments
www.ciscopress.com
Summary
• VTP was created to solve problems such as
cross-connected VLANS caused by
configuration inconsistencies
– With VTP, VLAN configuration is consistently
maintained across a VTP domain
• A VTP domain is made up of one or more interconnected
devices that share the same VTP domain name
• A switch can be in only one VTP domain
– VTP messages are encapsulated in a trunking
protocol frame, such as ISL or IEEE 802.1Q
– VTP switches operate in one of three modes: server,
client, transparent
www.ciscopress.com
Summary
• With VTP, each switch advertises the
following on its trunk ports:
– Management domain
– Configuration revision number
– VLANs that it knows about
– Parameters for the VLANs
• By default, server and client Catalyst
switches send VTP advertisements every
5 minutes or when a change occurs
www.ciscopress.com
Summary
• VTP servers inform neighbors of the current
configuration revision number
– The revision number is compared to the one in
memory and the switch overwrites the old
configuration if the number is higher
• At least one server needs to be in a VTP domain
• Before adding a VTP client, use the show vtp
status command to verify to VTP configuration
revision number on other switches in the VTP
domain
www.ciscopress.com
Summary
• When a host wants to communicate with a
host in a different VLAN, a router or Layer
3 switch must be involved to facilitate
inter-VLAN routing
– A physical interface on the router can be
divided into multiple logical subinterfaces
– Subinterfaces provide a flexible solution for
routing multiple data streams through a single
physical interface
www.ciscopress.com