Download High sensitive photodiodes

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Document related concepts

Stray voltage wikipedia, lookup

Current source wikipedia, lookup

Voltage optimisation wikipedia, lookup

Mercury-arc valve wikipedia, lookup

Rectifier wikipedia, lookup

Resistive opto-isolator wikipedia, lookup

Buck converter wikipedia, lookup

Distribution management system wikipedia, lookup

Rectiverter wikipedia, lookup

Alternating current wikipedia, lookup

Surge protector wikipedia, lookup

Mains electricity wikipedia, lookup

Triode wikipedia, lookup

Diode wikipedia, lookup

Opto-isolator wikipedia, lookup

Transcript
epc200
High sensitive photodiodes
General Description
Features
The epc200 is a high-sensitive, high-speed, low-cost photo diode
for light-barriers, light-curtains, and similar applications. These
photo diodes are designed to be used in a reverse-bias mode,
whereas the reverse bias voltage can be between 1.5 and 20
Volts. This device allows the design of short to long range light bar riers from a few millimeters up to tens of meters.
■ Low dark current
■ High sensitivity
■ High dynamic range
■ CSP package with very small footprint
■ Customer specific wavelength filter on request
■ Fully standard SMD assembly process compatible
The diodes feature a very high quantum efficiency of 90% in the
near IR range, a reverse breakdown voltage of up to 30 Volts and
a response time down to less than 100ns.
The advanced Chips Scale Package (CSP) makes this device ideal for miniaturized systems where a minimal space requirement is
key.
Applications
■ Light barriers and light curtains
■ Light barriers ranging from millimeters to tens of meters
■ Light curtains
■ Smoke detectors
■ Liquid detectors
■ Heart beat monitors
■ Oximeters
■ Position detection (rotary, linear, angle, etc.)
■ IR remote control of Hi-Fi, TV sets and other equipment
Product image
Figure 1: epc200 photo diodes
© 2014 ESPROS Photonics Corporation
Characteristics subject to change without notice
1/6
Datasheet epc200 - V1.2
Absolute Maximum Ratings (Notes 1, 2)
Recommended Operating Conditions
Min.
Max.
Units
Reverse Voltage V R
30.0 V
Reverse Voltage (V R)
1.5
20.0
V
Storage Temperature Range (T S)
-40°C to +85°C
Operating Temperature (T A)
-40
+85
°C
Lead Temperature solder, 4 sec. (T L)
+260°C
Relative Humidity (non-condensing)
+5
+95
%
Expected Lifetime (MTBF)
500 * 10 h @ 25°C
6
(<2 FIT)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended operating conditions
indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed
specifications and test conditions, see Electrical Characteristics.
Note 2: This device is a highly sensitive CMOS photodiodes with an ESD rating of JEDEC HBM class 2 (2kV to <4kV). Handling and as sembly of this device should only be done at ESD protected workstations.
General Characteristics
Unless otherwise stated, measuring parameters are V R = 5.0 V, -40°C < T A < +85°C, RL = 50 Ω
Symbol
Parameter
Conditions/Comments
Min.
Values
Typ.
Units
Max.
λS max.
λ
Wavelength
Wavelength Range
max. Sensitivity
S = 20 % of S max
Sλ
Spectral Sensitivity
η
Quantum Efficiency
λ = 850nm, V R = 5V, Ie = 1 mW/cm2
λ = 950nm, V R = 5V, Ie = 1 mW/cm2
λ = 850nm, V R = 5V, Ie = 1 mW/cm2
λ = 950nm, V R = 5V, Ie = 1 mW/cm2
0.61
0.43
90
62
A/W
A/W
%
φ
VO
Half angle
Open Circuit Voltage
Ie = 0.5 mW/cm2
±60
250
°
mV
0.25
-3.0
%/K
mV/K
VR = 5V, Ie = 1 mW/cm2, λ = 850 nm
VR = 5V, Ie = 1 mW/cm2, λ = 950 nm
VR = 5 V, TA= 20°C
VR = 20 V, TA= 20°C
Selected types with reduced dark current on request
18.7
13.2
2
5
μA
Ie = 1 mW/cm2, λ = 850 nm
VR = +1.5 V
photo current measured at R L = 50
Ω , λ = 850 nm, I P = 200 μA
VR = +5.0 V
20
300
TCV
TCO
850
450
Temperature Coefficient of I SC
Temperature Coefficient of V O
IP
Photo Current
IR
Dark Current
ISC
tr
Short-circuit Current
Rise/Fall Time
VR = +10.0 V
CO
NEP
Capacitance
Noise Equivalent Power
VR = +5V, ƒ = 100kHz, E = 0
VR = 5 V
1050
20
nm
nm
nA
μA
ns
140
70
22
1.2x10-14
pF
W/√Hz
Connection Diagram
TOP VIEW
Cathodes are
connected on chip
3
4
5
1
Pin
Assignment
1
Cathode
2
Cathode
3
Cathode
4
Cathode
5
Anode
2
Figure 2: Chip connections
© 2014 ESPROS Photonics Corporation
Characteristics subject to change without notice
2/6
Datasheet epc200 - V1.2
Other Parameters
(typical values, T amb = 25°C, VDD = 5.0V, IPD=0mA)
1E+3
1
0.9
1E+2
0.7
1E+1
0.6
0.5
Ip [μA]
0.4
0.3
0.2
1E+0
1E-1
1E-2
0.1
0
100
Angle [°]
1E+1
80
1E+0
60
1E-1
40
1E-4
20
1E-2
1E-3
0
1E-3
Relative Sensitivity
0.8
Ie [mW/cm2]
Photocurrent I P = ƒ(Ie), VR = 5 V, λ=850nm
Relative sensitivity vs. illumination angle
1
400
Rise Time
RIse / Fall time [ns], 10% - 90%
0.9
Relative Sensitivity
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
tbd
Fall Time
300
200
100
0
0
400
500
600
700
800
900
0
1000 1100
Wavelength [nm]
Characteristics subject to change without notice
2
3
4
5
6
7
8
9
10
Reverse Bias Voltage [V]
Relative spectral sensitivity (no daylight filter)
© 2014 ESPROS Photonics Corporation
1
Rise/ fall time versus reverse bias voltage
3/6
Datasheet epc200 - V1.2
Application Information
A typical application of this chip is shown in Figure 3. In this application, a reverse bias voltage of approx. 1.5 V is used. Since the appli cations are typically light barriers as shown in Figure 1, dark current is not important at all, even in the range of up to 100nA.
5V
epc200
C1
C3
R1
VDD
PD
OUT
epc13x
VN
CN
C2
VSS
Figure 3: Typical schematic circuit using an epc13x photo pulse amplifier
Recommended Components Values (examples only – depends on particular application case)
R1: 27k (bias resistor). Sensitivity can be reduced by the reduction of this resistor.
C1: Usually not needed. May be up to 100 pF (refer to the epc13x data sheet).
C2: 33nF (DC input current filter capacitor)
C3: 100nF or more (power supply filter capacitor)
Spectral Sensitivity
This photo diode contains an anti-reflection coating on the photosensitive surface. Standard versions have no optical filter in order to al low applications from the near UV to the near IR range. However, optical filters deposited on the photosensitive surface are available
upon request. The filter parameters can be adjusted in a wide range according to specific customer requirements.
Layout Information (all measures in mm,
)
CSP5 Package
Designed
Approved
Scale
max 0.10
Bottom View
Page
Part Name
<Partname>
File:
<Name>
26.02.2009
<Name>
<Data>
M 1:1
DIN A4
1
Part No.
Top View
<x000 000>
Thi s docume nt is co nfi den tial and pr ote cted by law and in ter nation al trade s. It mu st no t be sh own to any thir d pa rty n or b e co pied i n any fo rm withou t ou r wr itten p ermissi.on
Design rules
The cathode pins are connected on chip. A proper design ensures that all cathode pins are connected to the same voltage level.
All pins of the diode array should be connected.
max. 0.1524
1.00
1.75 +0.00/-0.10
1.75
0.50
1.75
0.26 ±0.04
photosensitive area
0.5x45°
0.05
Solder balls
Sn97.5Ag2.5
1.00
1
2
photo diode
area
1.65
5
max 0.10
1.00
4
3
1.75 +0.00/-0.10
∅ 0.30
no solder mask inside this area
Figure 4: Mechanical dimensions
© 2014 ESPROS Photonics Corporation
Characteristics subject to change without notice
Figure 5: Layout recommendation
4/6
Datasheet epc200 - V1.2
Packaging Information
(all measures in mm)
8
CSP5 Tape
4
Figure 6: Carrier tape dimensions & chip orientation
Tape & Reel Information
The devices are mounted on embossed tape for automatic placement systems. The tape is wound on 330 mm (13 inch) reels and individually packaged for shipment. General tape-and-reel specification data are available in a separate data sheet and indicate the tape
sizes for various package types. Further tape-and-reel specifications can be found in the Electronic Industries Association (EIA) stan dard 481-1, 481-2, 481-3.
epc does not guarantee non-empty cavities. Thus, pick-and-place machines should check the presence of a chip during picking.
It is highly recommended to use underfill after assembly of the chips to the PCB.
Ordering Information
Part Name
Part Number
Package
RoHS compliance
Packaging Method
epc200-CSP5
P100 179
CSP5
Yes
Reel
epc200 Chip Carrier
P100 205
PCB
Yes
Tray
Tape on request
Figure 7: epc200 photo diodes on chip carrier
© 2014 ESPROS Photonics Corporation
5/6
Datasheet epc200 - V1.2
Characteristics subject to change without notice
32/<7(&*PE+ 3RO\WHF3ODW] ':DOGEURQQ *(50$1<
7HO)D[ (0DLORHN#SRO\WHFGH ZZZSRO\WHFGH IMPORTANT NOTICE
ESPROS Photonics AG and its subsidiaries (epc) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products
are sold subject to epc’s terms and conditions of sale supplied at the time of order acknowledgment.
epc warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with epc’s standard
warranty. Testing and other quality control techniques are used to the extent epc deems necessary to support this warranty. Except
where mandated by government requirements, testing of all parameters of each product is not necessarily performed.
epc assumes no liability for applications assistance or customer product design. Customers are responsible for their products and appli cations using epc components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
epc does not warrant or represent that any license, either express or implied, is granted under any epc patent right, copyright, mask
work right, or other epc intellectual property right relating to any combination, machine, or process in which epc products or services are
used. Information published by epc regarding third-party products or services does not constitute a license from epc to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the
patents or other intellectual property of the third party, or a license from epc under the patents or other intellectual property of epc.
Resale of epc products or services with statements different from or beyond the parameters stated by epc for that product or service
voids all express and any implied warranties for the associated epc product or service. epc is not responsible or liable for any such
statements.
epc products are not authorized for use in safety-critical applications (such as life support) where a failure of the epc product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically
governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applica tions, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning
their products and any use of epc products in such safety-critical applications, notwithstanding any applications-related information or
support that may be provided by epc. Further, Buyers must fully indemnify epc and its representatives against any damages arising out
of the use of epc products in such safety-critical applications.
epc products are neither designed nor intended for use in military/aerospace applications or environments unless the epc products are
specifically designated by epc as military-grade or "enhanced plastic." Only products designated by epc as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of epc products which epc has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection
with such use.
epc products are neither designed nor intended for use in automotive applications or environments unless the specific epc products are
designated by epc as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, epc will not be responsible for any failure to meet such requirements.
© 2014 ESPROS Photonics Corporation
Characteristics subject to change without notice
6/6
Datasheet epc200 - V1.2
www.espros.ch