Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
This is what we want to produce Label angles Set the scale Import sketch dimensions Add linear dimensions • Select the file menu • Click on open • Select the design folder to be opened • Click on open • Rotate the sketch using the keyboard arrows • Click on the line selector • Move the pointer to the lines of the sketch • When the edge goes bright blue double click quickly so it goes red and activates the sketch Select the sketch dimension tool • Move the pointer to an edge • When it goes bright blue click and hold with the left hand button • Drag off the design, the dimension should follow If you need to change the dimension • Select the dimension selector • Move the pointer over the dimension until it goes bright blue. • Click twice quickly and the properties box should appear • Click in the length box, delete the existing one and type in the new one • Click on o.k. • Click on the traffic light to update the design • Select the sketch dimension tool • Move the cursor over the circle • When it turns bright blue click and hold the left hand button • Drag off to the side • Select the dimension selector • Pass the pointer over the dimension, when it goes bright blue double click quickly on it • The properties box should appear • Change the dimension if needed and click on o.k. • Press the traffic light to update the design if the dimension has been changed. Add any other important dimensions that the sketch will allow • In the file menu click on new • Select drawing • Click on o.k. Check the format is the correct size for the drawing Check the format is the correct size for the drawing • Click the scale tab • Check the scale is correct. (note if the model figure is bigger than the paper figure the drawings will be reduced, i.e, half scale) • Click on the drawing standard tab • Click on the drop down arrow • Click on the required standard • Click on o.k. • Select the drawing menu • Click on add modelling view • Make sure from workplane is selected • Make sure wheel support is highlighted in blue • Make sure base is selected • Click on o.k • Make sure the sketch selector is selected • Move the pointer to the sketch so it goes bright blue • Click on it so it goes red • Click again and hold • Drag the sketch to the right • Select the drawing menu • Select add modelling view • Make sure from workplane and wheel support are selected • Click on the arrow to drop the workplane menu • Select frontal • Click on o.k. • Make sure the sketch selector is selected • Move the pointer to the sketch so it goes bright blue • Click on it so it goes red • Click again and hold • Drag the sketch to the bottom of the page • Select the drawing menu • Select add modelling view • Make sure from workplane and wheel support are selected • Click on the arrow to drop the workplane menu • Select lateral • Click on o.k. • Make sure the sketch selector is selected • Move the pointer to the sketch so it goes bright blue • Click on it so it goes red • Click again and hold • Drag the sketch to the bottom of the page The base sketch will not show anything so we need to delete it • Make sure the sketch selector is selected • Move the pointer to the sketch so it goes bright blue • Click on it so it goes red • Press delete • Make sure the sketch selector is selected • Place the pointer over the sketch • Click twice quickly so the property box appears • Tick the scale box • Enter 3 as the zoom factor • Click on o.k. Do the same with the other sketch • Select the sketch selector • Select the frontal view, move the pointer over the sketch until it goes bright blue, click twice quickly to make it go red • Select the drawing menu • Click on align other views • Select the dimensions menu • Click on import sketch dimensions • Select the annotations selector • Move the pointer over the dimension so it goes bright blue • Click so the dimension goes red • Click and hold, drag the dimension to the side • Select the linear dimension tool • Put the pointer on the edge of the lateral view so it goes bright blue • Click once so it goes red • Put the pointer on the other edge so it goes blue • Click and hold with the left hand button • Drag the dimension off the drawing and let go • Select the linear dimension tool • Put the pointer on the round edge of the frontal view so it goes bright blue • Click once so it goes red • Put the pointer on the top edge so it goes blue • Click and hold with the left hand button • Drag the dimension off the drawing and let go • Select the radius tool • Put the pointer over the curve so it goes bright blue • Click and hold, drag the pointer off the drawing • Select the angular dimension tool • Put the pointer on the top edge of the frontal view so it goes bright blue • Click once so it goes red • Put the pointer on the side edge so it goes blue • Click and hold with the left hand button, the dimension should appear • Drag the dimension into position and let go • Select the annotation selector • Put the cursor over the dimension so it goes bright blue • Click on the dimension so it goes red • Click and hold, drag the dimension to the side • Click on the feature selector • Click on the upper curve so it goes red • Select the centre line menu • Click on centre points • Make sure the feature selector is still selected • Click on the opposite upper curve so it goes red • Select the centre line menu • Click on centre points • Select the linear dimension tool • Move the pointer to the centre of one cirle so it goes bright blue and click • Move the pointer to the other centre so it goes bright blue • Click so it goes red • Drag the pointer off the drawing • Select the feature selector • Select the bottom curve • Select the centre line menu • Click on centre point • Make sure the linear dimension tool is selected • Click on the centre point of the top curve • Click and hold on the centre of the other circle • Drag the dimension off the drawing Add a table as in the assembly section Save your drawing