Download Intro_PSpice

Week 1:
Preparing for PSpice Simulations

Week 1 is composed of two experiments from the lab manual

Separate lectures on Modules will be posted for each
experiment.
◦ Experiment 1: Breadboard Basics
◦ Experiment 3: Ohm’s Law
The remainder of this lecture is an introduction to PSpice.
PSpice is not needed for either Experiment 1 or 3, but will be
used in the experiment for Week 2. Therefore, I would like to
verify that you can launch the program and run a DC Bias
Point simulation.
◦ Please review the PSpice FAQ where fixes are posted for common
problems encountered
(http://computing.ece.vt.edu/wiki/PSpice_FAQ).
◦ If you can not get the program to run as described, please contact
Mr. McKagen to request his assistance. SW.A.T. may also be able to
help.

Please install one of the following versions of the program on
your computer:
◦ Virtual Machine version of 9.1 (see instruction on
http://computing.ece.vt.edu/wiki/PSpice_FAQ )
 This is our preferred version
◦ Version 9.1 (www.opel.ece.vt.edu/ece3274)
 Please install both Schematics and Capture
◦ Version 10 from CD included in J.G. Tront’s book
◦ Version 16.2 (computing.ece.vt.edu/wiki/Main_Page)

Schematics tends to be the program that works best with the
tablet, so most of my instructions will cover that.
◦ If you happen to be using capture, because schematics does not
work, please let me know so that I can post instructions for capture
also.

The first simulation that we will do in PSpice is
called Bias Point Detail.
◦ The calculations are:
 the DC node voltages - voltage at each intersection of a wire
and an end of a part
 The DC branch currents – the current flowing through each of
the components in the circuit.

Launch Schematics
◦ You will have to run as computer administrator
 Right click on the program name from the Start menu (PSpice
Student/Schematics) and select Run as administrator from
the drop-down list.
Select Draw/Get New Part, which will cause
a pop-up window to open with a list of all of
the parts available in the student version of
Schematics.
- Note that there is a key stroke shortcut
(Ctrl+G).

Type the name of the part in the box
located by Part Name
Or, scroll through the list of parts and
click on the name of the one that you
want put into the circuit, say Vdc,
which is a battery.
◦ Note that a description of the part will be
displayed once you select a part.

Then, click Place if you have more
parts to select or Place & Close if this
is the last part.

You can type it in directly into the box below the Toolbar
Help and then hit Enter.
No matter what way that you select a part, a symbol for a dc
battery (a pair of long and short parallel lines connected to 2
vertical lines). will appear attached to your cursor on the
schematic when you move your cursor on to grid field.
• Left Click to place the part in a specific location on the schematic.
• Additional left clicks will place more batteries on your schematic.
• Right Click to end the process of placing the part Vdc.
Component
PSpice Name
Component
PSpice Name
DC voltage supply
Vdc
Resistor
R
DC current supply
Idc
Capacitor
C
Ground
gnd_earth
Inductor
L
PSpice does not recognize a difference between lower and upper case.
Place two resistors and a ground on your circuit.
Note: I have turned the grid of points off on my
schematic, which can be done by selecting
Options/Display Options on the upper toolbar.

When the part is highlighted in red, which
happens when you first place a part or you click on
the symbol for the part on the schematic,
◦ You can rotate the part by 90o using a Ctrl-R keystroke.
◦ You can flip the part around a vertical axis using a Ctrl-F
keystroke.
Click on the pencil (the thin one).
Or you can select the pencil by
going to Draw/Wire on the upper toolbar.
Then, click the pencil tip to one
end of a part and then to the
end of another part to place a
wire between them.

The program places nodes (large dots on the
schematic) where wires intersect and where wires
and the end of parts touch.
◦ It is not critical to see a node when wiring between V1 and
R1 and between R1 and R2.
◦ However, there must be a node visible when you wire the
ground into the circuit.
Typical errors are (a) the ground is
missing in the circuit and (b) the
ground appears to be wired into
the circuit, but there is no node.

Double click on the default component value
◦ 1k (which is short hand for 1 kW or 1000 W) for the resistor.
◦ Type the desired component value in the pop-up window.
You do not have to include the unit.
 Click Redraw under View to erase ghost images.
Leave R2 as 1k.
1012
Tera
T
10-3
milli
m
109
Giga
G
10-6
micro
u
106
Mega
Meg
10-9
nano
n
103
Kilo
k
10-12
pico
p
PSpice doesn’t differentiate between lower and upper case. So, a
capital M is also a milli (10-3). Therefore, Meg is used for million.
3k or 3K or 3000 are all treated as the same number for R1.

For the voltage source, double click on the default
value, which is 0V for the voltage source.
◦ In the pop-up window that opens, replace the default value
and click OK.
 The value of the voltage source will change on the schematic.
Change the value of the dc voltage
source (V1) to 9V for the example circuit.

PSpice will not run a simulation unless your circuit
is saved.
◦ You can select any directory in which to save the .sch file.
 Note: You can send the .sch file to me if you need assistance
finding errors that prevent the simulation from running.

Click on Analysis/Setup or the
button.
◦ Bias Point Detail should be clicked. If not, do so.
The PSpice program installed
incorrectly if you can’t find this
button. See the PSpice FAQ for
help on troubleshooting

Click Analysis/Simulate from the upper toolbar or
click on the
button.
A pop-up window should
open, text should scroll by in
the bottom left box. After
“Simulation complete” is
printed, the run is finished.
Go back to the Schematic.

Click on Analysis/Display Results on Schematic and
enable the voltage and/or current display.
The voltage, which is
the node voltage, is
displayed in green,
the current, which is
the branch current,
is displayed in blue
on the circuit
schematic.
•
You can reposition the labels with the voltages and currents using a
click-and-drag.
• When you do this on a current label, an arrow is displayed on the schematic
that shows which direction that magnitude current is flowing.
• You should reposition labels on images that you submit in your lab reports so that the
component values are visible.
• The voltage dropped across R1 is equal to 9V – 2.25V = 6.75V.
Comment on Analysis


Note that the calculation performed by PSpice
Schematics is a nodal analysis.
The voltage drop across a component is the voltage
calculated using Ohm’s Law, V= IR. It is the
difference between node voltages.
◦ The first voltage (VA) is the node at which current is
entering the resistor R and the second voltage (VB) is the
one at which the current I is leaving the resistor.
V = VA – VB
•
If you go to Analysis/Examine Output, a text file will
open and contains:
– The net list, a list of the names of the nodes in the circuit,
the components connected to the nodes, and their values.
– The type of simulation run.
– Table of the nodes and the voltages at each node.
– A list of the voltage sources in the schematic , the currents
flowing out of the sources, and the total power dissipated
by the resistors in the circuit.