Download DC CIRCUIT EXERCISE

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Nanofluidic circuitry wikipedia , lookup

CMOS wikipedia , lookup

Mathematics of radio engineering wikipedia , lookup

Valve RF amplifier wikipedia , lookup

Schmitt trigger wikipedia , lookup

Multimeter wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Power electronics wikipedia , lookup

Two-port network wikipedia , lookup

Surge protector wikipedia , lookup

Operational amplifier wikipedia , lookup

TRIAC wikipedia , lookup

Power MOSFET wikipedia , lookup

Electrical ballast wikipedia , lookup

Wilson current mirror wikipedia , lookup

Opto-isolator wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Ohm's law wikipedia , lookup

Current source wikipedia , lookup

Current mirror wikipedia , lookup

Rectiverter wikipedia , lookup

Network analysis (electrical circuits) wikipedia , lookup

Transcript
SOLUTION USING THEVENIN’S THEOREM
Working out resistor currents in unbalanced bridge circuits
can be frustrating, especially when depending entirely on
Kirchoff laws to do so. See Fig-1 below. However, one can
employ other mathematical tools like Thevenin and Norton
equivalents called “Source Transformations” to make the task
easier. For example, Thevenin’s Theorem states that any
complex linear circuit can be simplified to an equivalent
voltage source and series resistor connected to a load resistor.
(See Fig-1A below)
Left click on this slide to see
how this is done.
Procedure:
1. Call Rx the Load Resistor (See Fig-1 below)
2. Remove Rx and calculate the Voltage potential between A & B This
is the equivalent Voltage source. (See Fig-2 below)
3. Place a short across 100V and calculate resistance between A & B
This result is the equivalent series resistance. (See fig-3 below)
4. Draw the series equivalent circuit and calculate the Rx current
(See Fig.4 below) This result, 0.98A, is the current through Rx.
Since the current through Rx (0.98A) is now
known, the remaining currents in Fig-1 can be
easily calculated using Kirchoff Laws.
KIRCHOFF LAWS
1.
Kirchoff’s Current Law: The sum of all currents entering a
node must be equal currents leaving the node.
2.
Kirchoff Voltage Law: The sum of the voltages around a
closed loop must equal to zero.
To set up the problem draw the circuit and make notations as follows:
1.
Draw the circuit and enter Volts and resistance values (see Fig-5)
2.
Using conventional current flow (+ to -) enter arrows indicating
direction of current flow in all resistors Label unknown currents I1,
I2, & I3 through R1, R2, & R3 respectively
3.
Label R4 current as (I1 - I3 ) & R5 current as (I2 + I3)
KIRCHOFF LAWS
1.
Since there are 3 unknowns currents (I1, I2 & I3), select 3
loops in Fig-5 and from these, develop 3 equations to be used
for working out I1, I2 & I3.
Loop 1: 100V, R1 & R4
Loop 2: 100V, R2 & R5
Loop 3: R1, R2 & R3
Eq. 1: 100 – R1 I1 – R4(I1 – I3) = 0
Eq. 2: 100 – R2 I2 – R5(I2 + I3) = 0
Eq. 3: R1 I1 + R3 I3 –R2 I2 = 0
Substitute resistor values for R1, R2 & R3
Eq. 1A: 100 – 12 I1 – 24(I1 – I3) = 0
Eq. 2A: 100 – 36 I2 – 18(I2 + I3) = 0
Eq. 3A: 12 I1 + 14 I3 –36 I2 = 0
KIRCHOFF LAWS
From previous slide
Eq. 1A: 100 – 12 I1 – 24(I1 – I3) = 0
Eq. 2A: 100 – 36 I2 – 18(I2 + I3) = 0
Eq. 3A: 12 I1 + 14 I3 –36 I2 = 0
Expand to get rid of parentheses
Eq. 1B: 100 – 12 I1 – 24I1 + 24I3 = 0
Eq. 2B: 100 – 36 I2 – 18I2 – 18I3 = 0
Eq. 3B: 12 I1 + 14 I3 –36 I2 = 0
Consolidating we get:
Eq. 1C: 100 – 36 I1 + 24 I3 = 0
Eq. 2C: 100 – 54 I2 – 18 I3 = 0
Eq. 3C: 12 I1 + 14 I3 –36 I2 = 0
We have 3 simultaneous equations with 3 unknowns to find
I1, I2 & I3. Now the fun begins.
From previous slide
Eq. 1C: 100 – 36 I1 + 24 I3 = 0
Eq. 2C: 100 – 54 I2 – 18 I3 = 0
Eq. 3C: 12 I1 + 14 I3 –36 I2 = 0
These 3 equations can be reduced to two equations with two unknown
currents using traditional algebra. The procedure is as follows:
Multiply Eq. 1C through by 18: 18(100 – 36 I1 + 24 I3 = 0) to get:
Eq. 1D: 1800 – 648 I1 + 432 I3 =0
Multiply Eq. 2C through by 24: 24(100 – 54 I2 – 18 I3 = 0) to get
2D: 2400 – 1296 I2 – 432 I3 =0
By Adding Eq. 1D to Eq. 2D we get: 4200 – 648 I1 – 1296 I2 or
Eq. 4A: 4200 = 648 I1 + 1296 I2 (One of 2 equations with 2 unknowns)
Repeat procedure using eq. 2C & 3C to get the other equation with 2 unknowns
KIRCHOFF LAWS
Eq. 2C: 100 – 54 I2 – 18 I3 = 0
Eq. 3C: 12 I1 + 14 I3 –36 I2 = 0
Multiply Eq. 2C by 14 to get 14 (100 – 54 I2 – 18 I3 = 0) or:
Eq. 2E: 1400 – 756 I2 – 252 I3 = 0
Multiply Eq. 3C by 18 to get 18(12 I1 + 14 I3 –36 I2 = 0) or:
Eq. 3E: 216 I1 + 252 I3 – 648 I2 = 0
Add Eq. 3E to Eq. 2E to get 1400 + 216 I1 – 1404 I2 or
Eq. 4B: 1400 = – 216 I1 + 1404 I2 (The 2nd Equation with 2 unknowns
So now we have:
Eq. 4A: 4200 = 648 I1 + 1296 I2
Eq. 4B: 1400 = – 216 I1 + 1404 I2
Multiply Eq. 4A by 1404 to get: Eq. 5A 5896800= – 909792 I 1 + 1819584 I2
Multiply Eq. 4B by 1296 to get: Eq: 5B 1814400 = 279936 I1 + 1819584 I2
Subtract Eq.5A from Eq. 5B to get: 4082400 = 1189728 I1 or I1 = 3.43A
KIRCHOFF LAWS
We calculated I1 = 3.43A going
through R1. I3 Should be easy to find.
Using the 100V, R1 R4 loop we get:
100 = (12 x 3.43) + 24(3.43 - I3) or
100 = 41.16 + 82.32 –24 I3 or
24 I3 = 23.48
I3 = 23.48 / 24 = 0.97833A ~ 0.98A
As you can see from the above application of Kirchoff Laws, it
takes a good working knowledge of Algebra and a close watch
on the details. Even with these qualities, there are many
pitfalls on the way to a solution: getting the signs wrong,
arithmetic errors, misplacement of variables etc. I don’t think I
want to ever repeat such an exercise again. When ever
possible, choose the Thev enin Voltage equivalents or the
Norton Current equivalents.