Download Lecture1 Introduction - University of California, Berkeley

EECS 150 - Components and Design
Techniques for Digital Systems
Lec 16 – Storage: DRAM, SDRAM
David Culler
Electrical Engineering and Computer Sciences
University of California, Berkeley
http://www.eecs.berkeley.edu/~culler
http://www-inst.eecs.berkeley.edu/~cs150
1
Recall: Basic Memory Subsystem Block Diagram
Word Line
Address
Decoder
n Address
Bits
Memory
cell
m Bit Lines
2n word
lines
what happens
if n and/or m is
very large?
RAM/ROM naming convention:
32 X 8, "32 by 8" => 32 8-bit words
1M X 1, "1 meg by 1" => 1M 1-bit words
2
Problems with SRAM
• Six transistors use up
lots of area
• Consider a “Zero” is
stored in the cell:
– Transistor N1 will try to pull
“bit” to 0
– Transistor P2 will try to pull
“bit bar” to 1
• If Bit lines are precharged high: are P1 and
P2 really necessary?
– Read starts by precharging
bit and ~bit
– Selected cell pulls one of
them low
– Sense the difference
Select = 1
P1
P2
Off On
On
On
On Off
N1
bit = 1
N2
bit = 0
3
1-Transistor Memory Cell (DRAM)
• Write:
row select
– 1. Drive bit line
– 2. Select row
• Read:
– 1. Precharge bit line to Vdd/2
– 2. Select row
– 3. Cell and bit line share charges
» Minute voltage changes on the bit line
– 4. Sense (fancy sense amp)
» Can detect changes of ~1 million
electrons
– 5. Write: restore the value
bit
Read is really a
read followed by
a restoring write
• Refresh
– 1. Just do a dummy read to every cell.
4
Classical DRAM Organization (Square)
bit (data) lines
r
o
w
d
e
c
o
d
e
r
row
address
Each intersection represents
a 1-T DRAM Cell
RAM Cell
Array
Square keeps the wires short:
Power and speed advantages
Less RC, faster precharge and
discharge is faster access time!
word (row) select
Column Selector &
I/O Circuits
data
Column
Address
Row and Column Address
together select 1 bit a time
5
DRAM Logical Organization (4 Mbit)
4 Mbit = 22 address bits
11 row address bits
11 col address bits
Column Decoder
…
Sense Amps & I/O
11
R
O
W
A0…A10
D
E
C
O
D
E
R
D
Q
11
Memory Array
(2,048 x 2,048)
Storage
Word Line Cell
• Square root of bits per RAS/CAS
– Row selects 1 row of 2048 bits from 2048 rows
– Col selects 1 bit out of 2048 bits in such a row
6
Logic Diagram of a Typical DRAM
RAS_L
A
•
•
9
CAS_L WE_L
256K x 8
DRAM
OE_L
8
D
Control Signals (RAS_L, CAS_L, WE_L, OE_L) are all active low
Din and Dout are combined (D):
– WE_L is asserted (Low), OE_L is disasserted (High)
» D serves as the data input pin
– WE_L is disasserted (High), OE_L is asserted (Low)
» D is the data output pin
•
Row and column addresses share the same pins (A)
– RAS_L goes low: Pins A are latched in as row address
– CAS_L goes low: Pins A are latched in as column address
– RAS/CAS edge-sensitive
7
Basic DRAM read & write
• Strobe address in two steps
8
DRAM READ Timing
•
RAS_L
Every DRAM access begins at:
–
–
Assertion of the RAS_L
2 ways to read: early or late v. CAS
CAS_L WE_L
A
256K x 8
DRAM
9
OE_L
D
8
DRAM Read Cycle Time
RAS_L
CAS_L
A
Row Address
Col Address
Junk
Row Address
Col Address
Junk
WE_L
OE_L
D
High Z
Junk
Data Out
Read Access
Time
Early Read Cycle: OE_L asserted before CAS_L
High Z
Data Out
Output Enable
Delay
Late Read Cycle: OE_L asserted after CAS_L
9
Early Read Sequencing
• Assert Row Address
• Assert RAS_L
– Commence read cycle
– Meet Row Addr setup time before RAS/hold time after RAS
• Assert OE_L
• Assert Col Address
• Assert CAS_L
– Meet Col Addr setup time before CAS/hold time after CAS
• Valid Data Out after access time
• Disassert OE_L, CAS_L, RAS_L to end cycle
10
Sketch of Early Read FSM
FSM Clock?
Row Address to Memory
Setup time met?
Assert RAS_L
Hold time met?
Assert OE_L, RAS_L
Col Address to Memory
Setup time met?
Assert OE_L, RAS_L, CAS_L
Hold time met?
Assert OE_L, RAS_L, CAS_L
Data Available (better grab it!)
11
Late Read Sequencing
• Assert Row Address
• Assert RAS_L
– Commence read cycle
– Meet Row Addr setup time before RAS/hold time after RAS
• Assert Col Address
• Assert CAS_L
– Meet Col Addr setup time before CAS/hold time after CAS
• Assert OE_L
• Valid Data Out after access time
• Disassert OE_L, CAS_L, RAS_L to end cycle
12
Sketch of Late Read FSM
FSM Clock?
Row Address to Memory
Setup time met?
Assert RAS_L
Hold time met?
Col Address to Memory
Assert RAS_L
Setup time met?
Col Address to Memory
Assert RAS_L, CAS_L
Hold time met?
Assert OE_L, RAS_L, CAS_L
Data Available (better grab it!)
13
Admin / Announcements
• Usual homework story
• Read: 10.4.2-3 and SDRAM data sheet
• Digital Design in the News
– Implanted microMEMS for wireless drug delivery
– IEEE Spectrum Chip Shots
http://www.mchips.com/tech_video.html
14
DRAM WRITE Timing
•
RAS_L
Every DRAM access begins at:
–
–
The assertion of the RAS_L
2 ways to write: early or late v. CAS
A
9
CAS_L WE_L
OE_L
256K x 8
DRAM
8
Col Address
Junk
D
DRAM WR Cycle Time
RAS_L
CAS_L
A
Row Address
Col Address
Junk
Row Address
OE_L
WE_L
D
Junk
Data In
WR Access Time
Early Wr Cycle: WE_L asserted before CAS_L
Junk
Data In
Junk
WR Access Time
Late Wr Cycle: WE_L asserted after CAS_L
15
Key DRAM Timing Parameters
• tRAC: minimum time from RAS line falling to the
valid data output.
– Quoted as the speed of a DRAM
– A fast 4Mb DRAM tRAC = 60 ns
• tRC: minimum time from the start of one row access
to the start of the next.
– tRC = 110 ns for a 4Mbit DRAM with a tRAC of 60 ns
• tCAC: minimum time from CAS line falling to valid
data output.
– 15 ns for a 4Mbit DRAM with a tRAC of 60 ns
• tPC: minimum time from the start of one column
access to the start of the next.
– 35 ns for a 4Mbit DRAM with a tRAC of 60 ns
16
Memory in Desktop Computer Systems:
• SRAM (lower density, higher
speed) used in CPU register
file, on- and off-chip caches.
• DRAM (higher density, lower
speed) used in main memory
Closing the GAP:
1. Caches are growing in size.
2. Innovation targeted towards higher bandwidth for memory
systems:
–
–
–
–
–
–
SDRAM - synchronous DRAM
RDRAM - Rambus DRAM
EDORAM - extended data out SRAM
Three-dimensional RAM
hyper-page mode DRAM video RAM
multibank DRAM
17
DRAM with Column buffer
R
O
W
A0…A10
D
E
C
O
D
E
R
…
11 Memory Array
(2,048 x 2,048)
Storage
Word Line Cell
Sense Amps
Column Latches
MUX
Pull column into fast buffer storage
Access sequence of bit from there
18
Optimized Access to Cols in Row
• Often want to access a sequence of bits
• Page mode
– After RAS / CAS, can access additional bits in the row by
changing column address and strobing CAS
• Static Column mode
– Change column address (without repeated CAS) to get
different bit
• Nibble mode
– Pulsing CAS gives next bit mod 4
• Video ram
– Serial access
19
More recent DRAM enhancements
• EDO - extended data out (similar to fast-page mode)
– RAS cycle fetched rows of data from cell array blocks (long access time,
around 100ns)
– Subsequent CAS cycles quickly access data from row buffers if within an
address page (page is around 256 Bytes)
• SDRAM - synchronous DRAM
– clocked interface
– uses dual banks internally. Start access in one bank then next, then receive
data from first then second.
• DDR - Double data rate SDRAM
– Uses both rising (positive edge) and falling (negative) edge of clock for data
transfer. (typical 100MHz clock with 200 MHz transfer).
• RDRAM - Rambus DRAM
– Entire data blocks are access and transferred out on a high-speed bus-like
interface (500 MB/s, 1.6 GB/s)
– Tricky system level design. More expensive memory chips.
20
Functional Block Diagram
8 Meg x 16 SDRAM
21
SDRAM Details
•
Multiple “banks” of cell arrays
are used to reduce access time:
–
•
•
•
–
–
•
•
Commands are sent using the RAS,
CAS, CS, & WE pins.
Address pins are “time
multiplexed”
During RAS operation, address lines
select the bank and row
During CAS operation, address lines
select the column.
“ACTIVE” command “opens” a
row for operation
–
Each bank is 4K rows by 512
“columns” by 16 bits (for our part)
Read and Write operations as
split into RAS (row access)
followed by CAS (column access)
These operations are controlled
by sending commands
–
•
Subsequent “READ” or “WRITE”
commands modify the contents
of the row buffer.
For burst reads and writes during
“READ” or “WRITE” the starting
address of the block is supplied.
–
•
•
transfers the contents of the entire to
a row buffer
Burst length is programmable as 1, 2,
4, 8 or a “full page” (entire row) with a
burst terminate option.
Special commands are used for
initialization (burst options etc.)
A burst operation takes  4 + n
cycles (for n words)
22
READ burst (with auto precharge)
23
WRITE burst (with auto precharge)
See datasheet for more details.
Verilog simulation models available.
24
Volatile Memory Comparison
The primary difference between different memory types is the bit cell.
• SRAM Cell
• DRAM Cell
addr
bit line
•
•
•
•
•
•
word line
word line
data
bit line
Larger cell  lower density,
higher cost/bit
No dissipation
Read non-destructive
No refresh required
Simple read  faster access
Standard IC process  natural
for integration with logic
bit line
•
•
•
•
•
Smaller cell  higher density,
lower cost/bit
Needs periodic refresh, and
refresh after read
Complex read  longer access
time
Special IC process  difficult to
integrate with logic circuits
Density impacts addressing 25
SDRAM Recap
• General Characteristics
– Optimized for high density and
therefore low cost/bit
– Special fabrication process –
DRAM rarely merged with logic
circuits.
– Needs periodic refresh (in most
applications)
– Relatively slow because:
» High capacity leads to large cell
arrays with high word- and bitline capacitance
» Complex read/write cycle.
Read needs “precharge” and
write-back
word line
DRAM bit cell
bit line
– Multiple clock cycles per
read or write access
– Multiple reads and writes
are often grouped together
to amortize overhead.
Referred to as “bursting”.
26