* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download UMC_90
Survey
Document related concepts
Control system wikipedia , lookup
Resilient control systems wikipedia , lookup
Ground (electricity) wikipedia , lookup
Electric power system wikipedia , lookup
Wireless power transfer wikipedia , lookup
Power engineering wikipedia , lookup
Electrical engineering wikipedia , lookup
Fault tolerance wikipedia , lookup
History of electric power transmission wikipedia , lookup
Embedded system wikipedia , lookup
Wassim Michael Haddad wikipedia , lookup
Alternating current wikipedia , lookup
Mains electricity wikipedia , lookup
Transmission tower wikipedia , lookup
Opto-isolator wikipedia , lookup
Public address system wikipedia , lookup
Transcript
Integrated Circuits and Systems Lab 612 Human++ from technology to emerging health monitoring concepts Advisor:Robert Chen-Hao Chang Student:Shiue Ru Chen Date:2010/06/04 Integrated Circuits and Systems Lab 612 Outline Overview of the BAN set Different biopotential signal sensing Micro-power generation Emerging health monitoring concepts A. Wireless sleep staging B. Wireless ECG patch Reference Integrated Circuits and Systems Lab 612 Overview of the BAN set up Sensor : processing the bio-signals Base station : collecting and managing the data-flow The incoming signal are amplified and filtered and the BAN is a typical star topology networks with TDMA Integrated Circuits and Systems Lab 612 Different biopotential signals Amplitude and frequency characteristics of different biopotential signals Integrated Circuits and Systems Lab 612 Sensor node • 1 EEG sensor node that can acquire, process and transmit 1 to 24 EEG signals. • 1 ECG sensor node that can acquire, process and transmit ECG signals. • 1 EMG sensor node that can acquire, process and transmit EMG signals. • 1 base-station that collects the information from the 3 sensor nodes. Integrated Circuits and Systems Lab 612 Functional diagram Signals are sampled at 1024Hz with a 12-bit resolution and transmitted over a wireless link operation in the 2.4GHz ISM band 1.Listen : the sensors receive their parameter from the base station 2.Processing : the biopotentical signals are monitored and processed 3.Transmit : the sensors send their data to the base station 4.Sleep : power save mode ,most of the electronics are switched off Integrated Circuits and Systems Lab 612 Ultra-low-power wireless The Nordic nRF24L01 achieves less than 20nJ/bit Another system can deliver a pulse rate up to 40MHz with a measured power consumption of 2mW, or 50pJ per pulse ,1nJ/bit. Integrated Circuits and Systems Lab 612 Ultra-low-power sensing EEG, ECG, EMG and EOG signals, presents an interesting challenge as these signals differ in amplitude and frequency characteristics Integrated Circuits and Systems Lab 612 UWB-IR The transmitted signal consists in pulses of short duration (~1-2 ns) that are separated by longer silent periods (~20 ns or more). 1.bandwidth larger than 500 MHz 2.Communications between 3.1GHz and 10.6GHz 3.Power spectral density(PSD)limit of -41dbm/MHz Feature: 1.High speed (400 Mbps) 2.Low power 3.Wireless transformation 4.Impulse signal 5.Range of 10m Integrated Circuits and Systems Lab 612 Architecture of the pulse generator It been implemented in a logic 0.18um CMOS technology And it can deliver a pulse rate up to 40MHz with a measured power consumption of 2mW, or 50pJ per pulse ,1nJ/bit. Ring oscillator has fast startuptime Integrated Circuits and Systems Lab 612 Example for EMG Listen and transmit mode consume about 90% of the power and the overall power less than 1mW if the measurement interval is longer than 1s Integrated Circuits and Systems Lab 612 Comparing (up) UWB-IR signal , there are idle time that can save power (down) narrowband radio signal , there are always active time Integrated Circuits and Systems Lab 612 Power breakdown for benchmarking example Active : optimizing the processing algorithm , reducing data memory sizes, decreasing processor complexity and cycle count Idle : clock gating control Leakage : using high threshold voltage cell Integrated Circuits and Systems Lab 612 Micro-power generation Heat flow generates a power density of about 20 mW / cm 2 A thermoelectric generator (TEG) output voltage of 0.7V at matched load Provide pulse-oximeter power At 22°C, wrist-watch type of TEG provide 0.2-0.3 mW density varying from 8 to 25 uW / cm 2 micromachined thermoelectric generator, which is expected to generate up to 30 μW/cm2 at a voltage exceeding 4.0 V EEG monitoring Integrated Circuits and Systems Lab 612 Seebeck effect A (+) T1 measure point T2 base point i T1>T2 B(-) The thermal emf is not define as temperature(T1-T2) . Integrated Circuits and Systems Lab 612 Schematic of a thermoelectric Typically based on Bi2Te3, the pillars have a lateral size of 0.3 – 1 μm and a height of 1 – 3 μm. A TEG optimized to obtain the maximum power will have a thermal resistance of about 200 cm2K/W per cm2 of surface Integrated Circuits and Systems Lab 612 Performance of the watch-like TEG 1.No physical activity 2.Working in office 3.Walking man Integrated Circuits and Systems Lab 612 Battery-less electronics Wireless body-powered pulse oximeter , a prototype of the battery-less electronics and the application running on a laptop. Integrated Circuits and Systems Lab 612 Emerging health monitoring concepts A. Wireless sleep staging 2-channel EEG, 2-channel EOG and 1-channel EMG Each node achieves a power consumption of 15 mW, for a sampling rate of 200 Hz Featuring: Reconfigurable gain and bandwidth, the read-out ASIC can be used to monitor EEG, EOG and EMG Integrated Circuits and Systems Lab 612 Comparing a. Now in hospital b. optimized Integrated Circuits and Systems Lab 612 Emerging health monitoring concepts B. Wireless ECG patch Feature: A fork-antenna and a snap-on connector, for connection to one electrode Maintain the overall power consumption around 10 mW for more than 5 days autonomy 3 with a battery of size 20x20x5 mm Integrated Circuits and Systems Lab 612 Comparing a. Holter device b. optimized Integrated Circuits and Systems Lab 612 3D SiP 3D SiP Wireless autonomous sensor node Integrated Circuits and Systems Lab 612 References 1.Julien Penders, Bert Gyselinckx, Ruud Vullers, Michael De Nil, Subbu Nimmala, Jef van de Molengraft, Firat Yazicioglu, Tom Torfs, Vladimir Leonov, Patrick Merken, Chris Van Hoof, “Human++: from technology to emerging health monitoring concepts “2008 2.Penders, J., Gyselinckx, B., Vullers, R., Rousseaux, O., Berekovic, M., De Nil, M., Van Hoof, C., Ryckaert, J.,Yazicioglu, R.F., Fiorini, P. and Leonov, V., 2007, in IFIP International Federation for Information Processing,Volume 249, VLSI-SoC: Research Trends in VLSI and Systems on Chip, eds. De Micheli, G., Mir, S., Reis, R.,(Boston: Springer), pp. 377–397