Download File

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Classical mechanics wikipedia , lookup

Newton's theorem of revolving orbits wikipedia , lookup

Relativistic mechanics wikipedia , lookup

Fictitious force wikipedia , lookup

Modified Newtonian dynamics wikipedia , lookup

Fundamental interaction wikipedia , lookup

Classical central-force problem wikipedia , lookup

Center of mass wikipedia , lookup

Rigid body dynamics wikipedia , lookup

Centripetal force wikipedia , lookup

Centrifugal force wikipedia , lookup

Inertia wikipedia , lookup

Force wikipedia , lookup

Seismometer wikipedia , lookup

Newton's laws of motion wikipedia , lookup

Gravity wikipedia , lookup

Buoyancy wikipedia , lookup

Transcript
Mass vs Weight




Mass (m) – amount of matter in an object
 It’s what provides the object’s inertia,
 It’s a constant no matter where it is measured
 Units: grams – standard in chemistry – think paperclip (slug)
kg – standard in physics – 1000 g – think textbook
Volume (V) – amount of space object takes up
Units: liter, cm3, m3, (gal, cup, in3)
Recall Density = m/V it is the mass to volume ratio
Weight (W) – the force of gravity on an object
 it’s how much gravity pulls on the mass of the object
 so depending on what the gravity is in your location, your
weight will vary
 Units: Newton, (lbs)
So while m ≠ W, they are proportional (m α W) if measured in
the same location.
The Math of Mass vs Weight
eq’n: W = mg where on Earth, g = 9.8 m/s2, down
units: N = kg m/s2
So a Newton is a derived unit, just like m/s or m/s2 .
derived unit – any unit which is a combination of
any of the fundamental units like meter, sec, kg…
but unlike m/s, it was a bit cumbersome to say, so
we gave it a nickname, that honored Issac Newton.
Note, DO NOT USE 1 kg = 9.8 N !
(since a kg should never be set = to a N)
so it is bad form to use this as a conversion factor to
get from mass to Weight
Tools to Measure Mass vs Weight

Spring scales – contain a spring that extends or
compresses depending upon how much push or pull is
applied – so they’re location ___________ - so they’re
good to measure ____
Ex:

Balances – compare the amount of material in one
object with the amount in another – so they’re location
___________ - so they’re good to measure _____
Ex:
But whether you’re measuring mass or weight is very
confusing to keep straight and often messed up in real
life – even by people of science!
Ex: “scale” at dr’s office … in lbs
“weigh” your sample of ____ in grams in chemistry
Net Force
Net force (Fnet) - the vector sum (both mag & direction)
of all the forces acting on an object at one time
 Last chapter we called this Resultant Force – FR
 If an object’s Fnet = 0, then the object satisfies the
condition in Newton’s 1st Law to be maintaining its
state of motion
- either at rest or constant velocity…
 So we say it is in a state of equilibrium
 the object CAN be moving, just constantly
 there can be lots of forces acting on it, as long as
they cancel each other to add to 0
Let’s look at a few examples:
1st consider a book sitting on a table
What are the forces acting on it?
 The Earth pulls down – force of gravity – W
 The table pushes up – force of support – FN
[Note: FN is the normal (perpendicular) force – the force of
support an object gets from the surface on which it rests – it
is always  to the surface, so
but also
]
free body diagram:
So, back to the book,
which is in equilibrium,
since it’s maintaining its state of motion (at rest)
Fnet = FN + W = 0
which means FN = - W
they are = magnitudes, but opposite direction!
2nd consider a block hung from a string
What are the forces acting on it?
 The Earth pulls down – force of gravity – W
 The string pulling up – force of tension – T
[Note: T is the supporting force applied to an object through a
long, stringy thing like
]
FBD:
So, back to the block,
which is in equilibrium,
since it’s maintaining its state of motion
Fnet = T + W = 0
which means T = - W
they are = mags, but opposite direction again.
3rd consider a block hung from two
vertical strings:
What are the forces acting on it?
 The Earth pulls down – force of gravity – W
 The strings pull up – 2 forces of tension – T1 & T2
FBD
once again, the block
is in equilibrium, so
Fnet = T1 + T2 + W = 0
which means T1 + T2 = - W
Are T1 & T2 equal to each other?
Most likely yes in this situation, but always?
Not necessarily – depends on how / where they’re
attached to the object and if the object is made of a
uniform material or not.
4th consider a block hung from 2 angled strings:
Both string’s tensions/scale’s readings get
greater as the angles get wider, but why?
 Since the tensions are angled, only the
vertical component of each actually pulls
straight up to support the weight of the
object. Now these 2 components, T1V & T2V ,
take on the values that the scales had
when they simply hung vertically.
See Figure 1

And the more horizontal the strings/scales
are, the more tension has to be put into the
strings/scales along the hypotenuse to keep
the vertical component of it big enough to
continue balancing the weight of the block,
downward.



The horizontal components don’t help to
support the weight at all, and in fact
always cancel each other out:
T1H = - T2H
Therefore, the resultant forces, T1 & T2 ,
would have to be larger than either of
their components.
and bigger than when they were simply
pulling straight up, as in 3rd example.
The readings on the scales, T1 & T2 ,
& their vertical components, T1V & T2V ,
only equal each other
(T1 = T2 and T1V = T2V)
if the supports are at equal angles.
5th consider a block hung from 2 unequally
angled strings:
The more vertical string/scale has the
greater tension… but why?
 the more vertical support has the larger
vertical component and therefore does
more (has > T) to support the weight
 but the vertical components will still add
to equal the weight of the object :
T1V + T2V = - W
 and the horizontal components will still
be equal but opposite to each other:
T1H = -T2H
Note: the string’s length does not
determine the amount of tension in it!
6th consider a block hung from two
scales in a row
Both scales read the entire weight of the
object they hold, with the top one
reading just a bit more, as it is holding
up the 2nd scale, as well as the object.