Download Digital Voltmeter Circuit using ICL7107

Digital Voltmeter Circuit using ICL7107
(ELECTRICAL4STUDY.COM)
Digital voltmeters are often preferred these days over analog voltmeters owing to their accuracy and
high rate of precision. Also digital systems are preferred because of their less exposure to noise and
good data compression capability. A voltmeter is an instrument measuring the potential difference
between two points. A typical digital voltmeter consists of a analog to digital converter and a digital
display.
Analog to digital conversion involves transforming a signal from its continuous form to discrete form
using electronic integrated circuitry. An analog to digital converter can be a dual slope converter,
successive approximation converter, flash converter or a delta sigma converter.
Here we design a analog to digital converter working as a digital voltmeter using a low power three
and half digit A/D converter ICL7107 having internal 7 segment decoders, display drivers, a
reference and a clock. An advantage is this IC can directly drive non multiplexed seven segment
display without any external decoding circuitry. The circuit can measure voltage in the range of
200mV to 2V with an interval of 0.001V.
Principle Behind the Circuit:
This circuit is based on the principle of using ICL7107 as an analog to digital converter. The whole
operation is divided into two phases- Analog to digital conversion and decoding. Analog to digital
conversion is done using the process of integrating and reference integrating. In other words, the
input signal is first integrated to bring the output of integrator to ramp signal and an opposite polarity
reference voltage is then integrated to bring the output of integrator back to zero. The resultant
digital code obtained is then decoded using to display decoders to drive the display unit.
Digital Voltmeter Circuit Diagram using ICL7107:
(ELECTRICAL4STUDY.COM)
How Design Digital Voltmeter Circuit?
Designing the circuit requires appropriate selection of the components as given below:
1. Selection of Oscillation Circuit Components: For a typical oscillating frequency of 48 KHz,
the oscillating resistor has been chosen to be about 100K and the capacitor about 100pF.
2. Reference Capacitor: The value of reference capacitor is chosen to be between 0.1uF and
1uF. Here we choose a 0.5uF electrolyte capacitor.
3. Auto-zero Capacitor: The auto zero capacitor is selected such that its value is between
0.01uF and 1uF. Here we select a 0.1uF capacitor.
4. Integrating Capacitor: The integrating capacitor forms an essential part of the integrating
circuit. Its value is determined by the integration period t, optimum integration current I and
integrated voltage Vint. For a time period of 83mSec, current of 4uA and voltage of 2V, the
value of capacitor is found to be around 0.16uF. Here select a 0.22uF capacitor.
5. Integrating Resistor: The value of this resistor is given by the full scale analog input voltage
and the optimum integration current. We select a resistor of 500K for a full scale input voltage
of 2V.
How to Operate Digital Voltmeter Circuit?
The IC is powered by a dual supply of +/- 5V. Once the circuit is powered, the reference signal is set
by adjusting the reference resistor. The reference voltage needs to be about half of the input voltage.
The oscillating components – resistor and capacitor determine the oscillating or clock frequency of
the device. The reference capacitor is charged to the reference voltage. A feedback loop is then
closed to charge the auto zero capacitor such that is compensates for any fluctuations in voltages.
Later the converter integrates the differential voltage at the input for a fixed time such that output of
the integrator is a ramp signal. A known reference voltage is then applied to the input of integrator
and is allowed to ramp till the output of integrator becomes zero. The time taken for the output to
return back to zero is proportional to the input signal and the digital reading is given as:
Display Count = (Vin/Vref)*1000.
The next process involves decoding the digital count to produce a seven segment compatible signal
so as to drive the displays. The digital output is then displayed on the multiplexed 7-segment display.
Applications of Digital Voltmeter Circuit:
1. This circuit can be used in digital multimeters to provide digital reading of measured voltage.
2. It can be used to measure AC and DC voltages.
3. It can be used to measure physical quantities like pressure, temperature, stress using
transducer circuit and signal conditioning circuit.
4. It can be used in applications where high accuracy and high resolution is required.
Limitations of Digital Voltmeter Circuit:
1. It can measure voltages only up to a low range.
2. The IC used is a CMOS device and is highly static.
3. Difference in reference voltage for negative and positive input voltage can cause rollover error,
i.e. a common mode error.
4. Using a full scale negative input voltage of 2V can sometimes cause output of the integrator to
saturate.
5. Internal heating from the LED drivers can cause degradation in performance.
6. Reference temperature coefficient, internal chip dissipation and package thermal resistance
tend to increase the noise level.