* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Visit us at www.mr
Survey
Document related concepts
Voltage optimisation wikipedia , lookup
Vacuum tube wikipedia , lookup
Electrical substation wikipedia , lookup
History of electric power transmission wikipedia , lookup
Alternating current wikipedia , lookup
Opto-isolator wikipedia , lookup
Mains electricity wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Current source wikipedia , lookup
Electrical ballast wikipedia , lookup
Buck converter wikipedia , lookup
Distribution management system wikipedia , lookup
Rechargeable battery wikipedia , lookup
Electric battery wikipedia , lookup
Transcript
¼ . 21A Solid State ‘Nano’ Switch Print Date31/10/2011 Visit us at www.mr-rcworld.co.uk. Page 1 of 2 Load - Lights / Pumps etc. Inside the Power Switch Load (Lights/Pump/Coil) Supply (Batteries) Batteries RED Spot (+) (+) (-) (-) Supply (Batteries) ***VERY IMPORTANT*** Internal Damage will occur if the supply lines are cross polarised (Positive on Negative, Negative on Positive) If you are using LED’s you MUST fit resistors into the circuit Battery Voltage 5.0V 6.0V 9.0V 12.0V . Solder Resistor (Ohms) 150 200 360 510 Flat on package denotes the Cathode LED Short Leg is the Cathode. Cathode is connected to the Negative side of the batteries MKIII ONBOARD SIGNALLING LEGEND Load - Lights / Pumps etc. POWER UP INITIALISE - 3 RAPID FLASHES SWITCH ACTIVE - LED ON (LIT) SWITCH INACTIVE - LED OFF (UNLIT) IF LED IS PERMANENTLY ‘ON’ AFTER THE INITIAL POWER-UP PULSES THEN EITHER NO RC SIGNAL IS PRESENT (TRANSMITTER TURNED OFF) OR YOU HAVE THE WRONG TRANSMISSION ******IMPORTANT**** Always fit a Fuse between your batteries and the Load. If there is a wiring short circuit or a defect, there is normally enough current in your batteries to set fire to your precious Model. Fuses, Diodes, Resistors and Suppression Kits are available on our website at www.mr-rcworld.co.uk Rev No 3 Feb 2012 Mr RC WORLD RC Electronic Solid State Switch Connection Details Eng. Scale 1:1 Drawing No 1 of 3 . BATTERY PACK (+) (-) (Red = Positive) (Black = Negative) RED Spot (+) (+) WHEN WIRED IN THIS CONFIGURATION THE LOAD WILL BE TURNED ‘ON’ WHEN THE ONBOARD RED LED IS ‘ON’ Z Z If you are using LED’s you MUST fit resistors into the circuit Battery Voltage 5.0V 6.0V 9.0V 12.0V . Solder Resistor (Ohms) 150 200 360 Flat on package denotes 510 the Cathode LED Short Leg is the Cathode. Cathode is connected to the Negative side of the batteries PUMP LIGHTS Rev No OCT 2012 Mr RC WORLD RC ‘nano’ SWITCH BASIC WIRING DIAGRAM Scale 1:1 Drawing No 2 of 2 If you are using LED’s you MUST fit resistors into the circuit SMD 1206, 0805 & 0603 Battery Voltage 5.0V 6.0V 9.0V 12.0V Resistor (Ohms) 150 200 360 510 Flat on package denotes the Cathode . A Always fit a Fuse between your batteries and the Load. If there is a wiring short circuit or a defect, there is normally enough current in your batteries to set fire to your precious Model. Fuses, Diodes, Resistors and Suppression Kits are available on our website at www.mr-rcworld.co.uk Solder FLAT CATHODE K ANODE Cathode usually marked by a Green Band or Arrow on Underside of Device. *****Please Note***** The information on LED current limiting resistors is generic to all LED applications. LED Short Leg is the Cathode. Cathode is connected to the Negative side of the batteries With most of our kits it is unnecessary to use a resistor in the circuit as they are already built in on the Module. CHECK THE DATASHEET FIRST! The Resistor can be placed in either Leg of the LED Rev No Sept 2009 Replacement or additional LED’s and Resistors can be purchased from our website www.mr-rcworld.co.uk Mr RC WORLD Model Aircraft Strobe and Beacon Lighting Kit LED General Information Eng. Drawing No 3 of 3 Scale 1:1