Download High Voltage Solid-State Circuits for Tube Guitar

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Oscilloscope types wikipedia , lookup

Multimeter wikipedia , lookup

Video camera tube wikipedia , lookup

Cavity magnetron wikipedia , lookup

List of vacuum tubes wikipedia , lookup

Cathode ray tube wikipedia , lookup

Index of electronics articles wikipedia , lookup

CMOS wikipedia , lookup

Integrating ADC wikipedia , lookup

Josephson voltage standard wikipedia , lookup

TRIAC wikipedia , lookup

Beam-index tube wikipedia , lookup

Amplifier wikipedia , lookup

Transistor–transistor logic wikipedia , lookup

Oscilloscope history wikipedia , lookup

Radio transmitter design wikipedia , lookup

Power electronics wikipedia , lookup

Ohm's law wikipedia , lookup

Wien bridge oscillator wikipedia , lookup

Electrical ballast wikipedia , lookup

Tube sound wikipedia , lookup

Surge protector wikipedia , lookup

Schmitt trigger wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Regenerative circuit wikipedia , lookup

Current source wikipedia , lookup

Voltage regulator wikipedia , lookup

Operational amplifier wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Current mirror wikipedia , lookup

Rectiverter wikipedia , lookup

Opto-isolator wikipedia , lookup

Valve RF amplifier wikipedia , lookup

Power MOSFET wikipedia , lookup

Transcript
High Voltage Solid-State Circuits for
Tube Guitar Amplifiers
●
●
●
●
●
The IRF820
MOSFET has a
voltage rating of
500v, it should
work well in
preamp stages of
most tube amps.
The 100 ohm
resistor is there
to suppress H.F.
oscillations. If
IRF820 is
physically close
to the 12AX7
plate, you
probably won't
need it.
You can see
how the
MOSFET is
equivalent to a
triode: Source =
Cathode; Gate =
Grid; Drain =
Plate
You cannot use
the MOSFET as
a direct
replacement for
a typical tube
gain stage. The
MOSFET will
not "self bias"
like a typical
cathode-biased
tube stage.The
MOSFET is an
"enhancement
device" while a
triode is a
"depletion"
device.
In this circuit, it
is not necessary
to use a heatsink
on the IRF820.
You can if you
want.
●
●
●
●
●
This circuit is a
"cascode". It is
capable of high
gain, is very
linear and is nonmicrophonic.
A comparison to
triode: JFET
Source =
Cathode; JFET
gate = grid;
MOSFET Drain
= Plate.
The MOSFET is
wired as a
simple voltage
regulator. The
1M resistor,
zener and 10uf
cap set the
reference
voltage. Use a
24v or less
zener.
A signal applied
to the "grid"
causes the
current through
the JFET,
MOSFET and
100k "plate"
resistor to vary.
The output is
tapped off the
"plate" resistor,
like a normal
tube gain stage.
Select a value
for Rs that sets
the "plate"
voltage at
approximately
50% of the
supply voltage.
Try typical
12AX7 cathode
resistor values.
Check the gain.
If you want
more gain, add
bypass cap Cb.
If that gives too
much gain, put
resistor Rb in
series with
bypass cap. The
value of bypass
cap can be used
for tone shaping,
●
●
●
as in triode
stage.
The "plate"
resistor can be
varied over a
wide range
similar to
12AX7. The
output cap can
be varied for
tone shaping
purposes.
This circuit
works well as a
1st gain stage, or
a reverb return
amplifier.
No heatsink is
required for the
IRF820 in this
configuration.
This is similar to the
High Voltage Solid
State Preamp stage,
with the following
exceptions:
●
●
●
●
The "plate" load
is a standard
Fender-style
reverb
transformer.
The "cathode" is
unbypassed.
The zener value
has been
reduced to 4.7v
The zener is tied
to the "cathode"
instead of
ground. This
allows a fairly
large input
signal to pass
through
●
●
relatively clean.
This circuit can
be inserted
anywhere you
would put the
standard 12AT7based circuit.
A small heatsink
is required for
the IRF820.
Remember that
the heatsink is
connected to the
MOSFET Drain
and has high
voltage on it.