Download Design Strategy For Barrel Shifter Using 2:1 Mux at 45 nm

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Electronic engineering wikipedia , lookup

Islanding wikipedia , lookup

Electrification wikipedia , lookup

Electrical substation wikipedia , lookup

Audio power wikipedia , lookup

Power over Ethernet wikipedia , lookup

Buck converter wikipedia , lookup

Electric power system wikipedia , lookup

Power electronics wikipedia , lookup

Amtrak's 25 Hz traction power system wikipedia , lookup

Integrated circuit wikipedia , lookup

Rectiverter wikipedia , lookup

History of electric power transmission wikipedia , lookup

Voltage optimisation wikipedia , lookup

Power engineering wikipedia , lookup

Control system wikipedia , lookup

Switched-mode power supply wikipedia , lookup

AC adapter wikipedia , lookup

Alternating current wikipedia , lookup

Mains electricity wikipedia , lookup

Digital electronics wikipedia , lookup

CMOS wikipedia , lookup

Transcript
IJSART - volume 1 Issue
4 –APRIL 2015
ISSN [ONLINE]: 2395-1052
Design Strategy For Barrel Shifter Using 2:1
Mux at 45 nm and 90 nm Technology Node
Amrita Pahadia1,Dr. Uma Rathore Bhatt2,Mr. Vijay Bhatt3
Department of Electronics & Telecommunication.
1, 2
Institute of Engg. &Technology ,DAVV
3
Chamelidevi Institute of Techology and management, Indore
Abstract- Designing a mux for low power to use it as a
repetitive block in the barrel shifter will considerably reduce
the simulation time .our basic objective is to compare existing
2:1 multiplexers with proposed multiplexer design in term of
power consumption ,temperature sustainability ,noise
immunity and frequency, so that a fast and optimized barrel
shifter can be designed by the help of it.a 2:1 multiplexer[7] is
a basic building block of the “switch logic”. The multiplexer
circuit is typically used to combine two or more digital signals
onto a single line, by placing them there at different times.
Technically, this is known as time-division multiplexing.
Multiplexers can also be used as programmable logic devices.
By specifying the logic arrangement in the input signals, a
custom logic circuit can be created. The selector inputs then
act as the logic inputs. This is especially useful in situations
when cost is a factor and for modularity. The increasing
prominence of portable systems and need to limit power
consumption has led to rapid and innovative developments in
low power vlsi design during recent years. The driving forces
behind these developments are portable device applications
requiring low power consumption and high throughput due to
their small chip size with large density of components,
increased complexity and high frequencies.
Keywords: power
temperature
consumption,
propagation
Bit vector for A is denoted as a7a6a5a4a3a2a1a0 and the
shift/rotate amount, B, is 3 bits.
A= a7a6a5a4a3a2a1a0 and B= 3
Operation
Y
3-bit shift right logical
0 0 0 a7 a6 a5 a4 a3
3-bit shift right arithmetic
a7 a7 a7 a7 a6 a5 a4 a3
3-bit rotate right
a2 a1 a0 a7 a6 a5 a4 a3
3-bit shift left logical
3-bit shift left arithmetic
a4 a3 a2 a1 a0 0 0 0
a7 a3 a2 a1 a0 0 0 0
3-bit rotate left
a4 a3 a2 a1 a0 a7 a6 a5
delay
I. INTRODUCTION
Barrel shifter is an integral component of many
computing systems due to its useful property that it can shift
and rotate multiple bits in a single cycle . Barrel shifter is an
important block of a floating point arithmetic block and used
to shift the data by n bits.logic diagram of barrel shifter is
shown in fig1. designed using Dsch tool The design of barrel
shifter is almost symmetric and can be done using repetitive
combinational logic blocks. The shifter[5] is an integral part of
many digital designs .there are many application that require
shift operation including CPUs ,floating point operation(like
addition, subtraction, normalization),variable length coding
etc.A barrel shifter needs nlog2 mux for n bit shifting and
therefore designing a mux for low power to use it as a
repetitive block in the barrel shifter will considerably reduce
Page | 192
the simulation time .We designed and compare the various
existing 2:1 multiplexer in term of power supply voltage
versus power consumption and, temperature sustainability.
All the post layout simulation have been performed at 45nm
and 90nm technology on dsch 3.5 version and microwind 3.5
version EDA tool.We assume A to be the input operand, B to
be the shift/rotate amount, and Y to be the shifted/rotated
result. We define A to be an n-bit value, where n is an integer
power of two. Therefore,B is a log2(n)-bit integer representing
values from 0 to n-1.
Table I .shift and rotate examples for A= a7a6a5a4a3a2a1a0
and B= 3 bit
Materials and methods:
A B-bit shift right logical operation performs a B-bit right
shift and sets the upper B bits of the result to zeros.
A B-bit shift right arithmetic operation performs a B-bit right
shift and sets the upper B bits of the result to a n-1 ,which
corresponds to the sign bit of A.
A B-bit rotate right operation performs a B-bit right shift and
sets the upper B bits of the result to the lower B bits of A.
www.ijsart.com
IJSART - volume 1 Issue
4 –APRIL 2015
A B-bit shift left logical operation performs a B-bit left shift
and sets the lower B bits of the result to zeros.
A B-bit shift left arithmetic operation performs a B-bit left
shift and sets the lower B bits of the result to zeros. The sign
bit of the result is set to a n-1.
A B-bit rotate left operation performs a B-bit left shift and sets
the lower B bits of the result to the upper B bits of A.
Various 2:1 multiplexer circuits simulations are performed on
90nm and 45nm technologies with supply voltage ranging
from 0.6V to 1.4V. In order to find out the optimized design
in terms of power, delay, power-delay product, the simulation
have been carried out at varying supply voltages, temperatures
and operating frequencies..
ISSN [ONLINE]: 2395-1052
product, the simulation have been carried out at varying
supply voltages , temperatures and operating frequencies.
III. PRIOR WORK
Prior design was differential cascade voltage switch
logic. require both true and complemented signals to be routed
gate. As shown in Design Fig.2 the circuit require both
inverting and non inverting signals which takes large wiring
area. So by adding two NMOS transistor in pull up part of
existing 2:1 multiplexer[5] the circuit shows remarkable
improvement over the existing design.
Results and discussion:
1)
VDD versus power consumption of existing and
and proposed mux at 90nm and 45nm technology.
Existing 2:1 multiplexer:
DCVSL (Differential Cascode Voltage Swith Logic)
The Prior technique of designing low power 2:1 Mux[7]
Presented is Differential Cascode Voltage Swith
Logic(DCVSL)circuit. Schematic of DCVSL circuit is shown
in the Fig. 3. Cascode Voltage Switch Logic (CVSL) refers to
a CMOS-type logic family which is designed for certain
advantages. A logic function and its inverse are automatically
implemented in this logic style. The pull-down network
implemented by the NMOS logic tree generated
complementary output. The advantage of DCVSL is in its
logic density that is achieved by elimination of large PFETS
from each logic function.
Fig 1: logic diagram of barrel shifter
II. RESEARCH ELABORATIONS
We compares the proposed design(MDCVSL) and
existing 2:1 multiplexer design(DCVSL)[7] in term of power
consumption and temperature for two technology nodes i.e.
45nm and 90nm.
Various 2:1 multiplexer circuits simulations [6]are
performed on 90nm and 45nm technologies with supply
voltage ranging from 0.6V to 1.4V. In order to find out the
optimized design in terms of power, delay, power-delay
Page | 193
www.ijsart.com
IJSART - volume 1 Issue
S.N
O.
VDD
(v)
1
0.6
2
0.8
3
1
4
1.2
5
1.4
IV.
4 –APRIL 2015
POWE
R
CONS
UMPT
ION
OF
PROP
OSED
MUX(
MDCV
SL)
90nm
(µw)
POWE
R
CONS
UMPTI
ON Of
PROP
OSED
MUX
(MDC
VSL)
45nm
15.626
µw
33.836
µw
59.422
µw
92.763
µw
0.134
mw
7.916
µw
16.653
µw
29.276
µw
46.172
µw
67.730
µw
ISSN [ONLINE]: 2395-1052
POW
ER
CONS
UMP
TION
OF
EXIS
TING
MUX
(DCV
SL)
90nm
POWER
CONSU
MPTIO
N
OF
EXISTI
NG
MUX
(DCVSL
)
45nm
20.427
µw
46.004
µw
82.201
µw
0.129
mw
0.186
mw
9.542 µw
20.253
µw
35.462
µw
55.495
µw
80.622
µw
Fig
2:
Exist
ing
2:1
Mult
iplex
er
Desi
gn
(DC
VSL
)
60
50
40
30
20
10
0
VDD(v)
mdcvsl
(µw)at
45nm
0.6 0.8 1 1.2
Fig.5 shows graph between Vdd versus power consumption
for 45nm technology node
2) Temperature versus power consumption of existing and
proposed mux at 90nm and 45nm technology
Tem
p.
(°C)
PROPOSED 2:1 MULTIPLEXER DESIGN
MDCVSL (Multiplexer double cascade voltage switch
logic)
10
30
50
70
90
POWE
R
CONSU
MPTIO
N OF
PROPO
SED
MUX(
MDCV
SL)
90nm
in µw
62.27
58.957
56.118
53.662
51.516
POWER
CONSU
MPTION
Of
PROPOS
ED
MUX(M
DCVSL)
45nm in
µw
29.276
27.858
26.642
25.590
24.670
POWER
CONSUM
PTION OF
EXISTING
MUX
POWER
CONSUM
PTION OF
EXISTING
MUX
(DCVSL)
90nm in
µw
(DCVSL)
45nm in
µw
86.358
81.522
77.354
73.738
70.581
84.748
79.949
33.723
32.420
31.275
LAYOUT DIAGRAM OF MDVSL:
Fig3: proposed 2:1 Multiplexer Design (DCVSL)
100
80
60
40
20
0
VDD(v)
0.6 0.8 1 1.2
mdcvsl(
µw)at
90nm
Fig.4 shows graph between Vdd versus power consumption
for 90nm technology node
Page | 194
Fig.5 Layout diagram of proposed mux in 45 nm technology
www.ijsart.com
IJSART - volume 1 Issue
4 –APRIL 2015
ISSN [ONLINE]: 2395-1052
V. CONCLUSION
This paper concluded with the efficient approach of 2:1
multiplexer designed using Dsch tool for 45nm and 90nm
technology.power consumption for given supply voltage is
smaller in 45nm technology compare to 90nm technology .The
post layout simulation have been done for the proposed circuit
in order to show improvement in power consumption over
supply voltages,temperature.The net effect is that proposed 2:1
multiplexer shows a much better performance for 45nm
technology compared to 90nm technology.
REFERENCES
[1] [1] Shen-fu Hsiao, Jia-Stang Yeh, and Da-Yen Chen,
“High Performance Multiplexer Based Logic Synthesis
Using Pass-transistor Logic”,Taylor & francis Gropu,
VLSI Design, vol. 15(1), pp. 417-426, in year 2002.
[2] [2] M. Morris Mano, R. Kime, Logic and Computer
Design Fundamentals, Pearson Education, 2nd edition,
2001.
[3]
N. Weste and D. Harris. CMOS VLSI Design: A
Circuits and Systems Perspective, Addison Welsey, 3rd
Ed., 2004.
[4] M. Janaki Rani ,S. Malarkann, leakage power reduction
and analysis of CMOS sequential circuits, International
Journal of VLSI design & communication Systems
(VLSICS) ,vol.3, no.1, Feb.2012, pp.13-23.
[5] Abhijit Asati, Chanda Shekhar, A purely Mux based
high speed barrel shifter VLSI implementation using
three different logic design styles, International
Conference on Mechanical Engineering and Technology,
Springer, vol.125, pp.639-646,2012
[6] Illa Gupta, Neha Arora, and Prof. B.P. Singh,
“Simulation and analysis of 2:1 mux in 90nm
technology,” IJMER, Vol. 1, Issue.2,mar-april 2012,pp642-646,ISSN:2249-6645
[7] Prasad D Khandekar, Dr. Mrs. Shaila Subbaraman,
Venkat Raman Vinjamoori ”Low Power 2:1 MUX for
Barrel Shifter” First International Conference on
Emerging Trends in Engineering and Technology.
[8] Rinu Pappachan,V.Vijaykumar, T. Ravi and V. Kannan,
“Design and Analysis of 4-Bit Low-Power Barrel Shifter
in 20nm FINFET Technology”, IJES, Volume-2, Issue3, pp.17-25, 2013.
[9] Behzad Razavi.”design of analog CMOS Intgration
circuit”,Tata McGrew Hill Edition year 2002.
Page | 195
www.ijsart.com