* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download - Satcure
Power factor wikipedia , lookup
Power engineering wikipedia , lookup
Buck converter wikipedia , lookup
Power over Ethernet wikipedia , lookup
Electric power system wikipedia , lookup
Fault tolerance wikipedia , lookup
Voltage optimisation wikipedia , lookup
Amtrak's 25 Hz traction power system wikipedia , lookup
Alternating current wikipedia , lookup
Rectiverter wikipedia , lookup
Distribution management system wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Mains electricity wikipedia , lookup
Printed circuit board wikipedia , lookup
Capacitor types wikipedia , lookup
Ceramic capacitor wikipedia , lookup
Electrolytic capacitor wikipedia , lookup
Aluminum electrolytic capacitor wikipedia , lookup
Tantalum capacitor wikipedia , lookup
Niobium capacitor wikipedia , lookup
RELKIT 33e Power supply capacitor Relkit for Grundig GDS3000/Thomson DSI410 This kit is for the PSSH370603A PSU made by Samsung (it has REV2.0 printed in a corner) & PSSH370604A. These PSUs are interchangeable with each other but NOT with other PSUs. Kit also suitable for DHD4000. The following components are supplied: C103 . . . . . . . . . . . C203, 211. . . . . . . . C204 . . . . . . . . . . . C206 . . . . . . . . . . . C207 . . . . . . . . . . . C208, 212, 213, 215. C209, 214. . . . . . . . C210, 216. . . . . . . . C101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22µF/50v 1500µF/10v UHR (gold stripe) type [1500µF/35v]§ 1µF/50v 1000µF/10v 330µF/10v 100µF/50v 47µF/50v 470µF/25v 82µF/400v (tags may need to be bent to fit). [100µF/400v]§ Not supplied IC101. . . . . 1M0365R (TO-220 in PSSH370603A) 5M0365R (8-pin DIL in PSSH370604A). § Note: all capacitors rated at 105°C. Some have a higher voltage rating or capacitance than originals, to improve ESR value. * Important: some capacitors may hold a charge for hours after power is disconnected. These can safely be discharged with a resistor of around 10 Ohms. Alternatively, shorting across with pliers is acceptable but only for capacitors which are going to be replaced! OBSERVE STATIC HANDLING PRECAUTIONS To avoid damage to semiconductors, observe the normal rules with regard to electrostatic charge. Since the end result depends upon your own skill and fault finding ability, the supplier will accept no responsibility for loss, damage or injury caused by your use of this kit. This information is the best available at the time of writing (Dec 2008). The black lines on the PCB indicate the negative (stripe) wire of the capacitor! See blue stripes on photo, below. Where capacitors are glued together, you can either cut the glue with a sharp knife or desolder all the glued parts, remove them as a cluster, then separate and replace the parts which don't need to be changed. As capacitors supplied tend to be slightly wider than originals, fit largest first, bend wires over to hold them, and solder when they are all positioned neatly. Make sure capacitor metal cans can not overlap any component leads and short circuit. The multi-pin plug connecting the power supply output to the main board can develop bad connections. This fault can be alleviated by bending the pins slightly. You can also spray a little WD-40 on the pins then work the plug up and down several times to clean the contacts. Finally, you can solder a wire to the copper track that joins the black wire pins together beneath the PSU and solder its other end to the nearest corner of the tuner module. ©Copyright 2005 SatCure PSSH370603A PSU Thomson DHD-4000 Important Notes C203 and C211 (1500uF) are physically too high and foul on the box lid. They have to be soldered on long legs then folded over the other capacitors and components, which themselves have to be mounted leaning over to make space. C101 only just fits; the lid scrapes the top of it. Please fix a suitable piece of insulating material to the lid to ensure that the capacitor can not make contact.