* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download DASH LIGHT DIMMER
Electrical ballast wikipedia , lookup
Transmission line loudspeaker wikipedia , lookup
Alternating current wikipedia , lookup
History of electric power transmission wikipedia , lookup
Power inverter wikipedia , lookup
Control system wikipedia , lookup
Voltage optimisation wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Stray voltage wikipedia , lookup
Phone connector (audio) wikipedia , lookup
Ground (electricity) wikipedia , lookup
Ground loop (electricity) wikipedia , lookup
Voltage regulator wikipedia , lookup
Two-port network wikipedia , lookup
Power electronics wikipedia , lookup
Solar micro-inverter wikipedia , lookup
Buck converter wikipedia , lookup
Mains electricity wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Schmitt trigger wikipedia , lookup
Current mirror wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
DASH LIGHT DIMMER Installation Instructions for – P/no. 97135840, 12/24Vdc module GENERAL The 971358400 Dash Light Dimmer is designed to follow the voltage from an existing automotive style dimmer circuit and supply a similar voltage out, to power equipment not included in the original manufacturers wiring. This is necessary on systems using a low resistance, high wattage rheostat for the dimmer, as too many lamps on the original dimmer circuit will result in a costly burnt out unit. Extra illumination lamps are often included as part of any after-market accessories such as radio/CD players, CB radios, etc, and the total wattage of these, combined with the original dash illumination is usually more than the design rating of the OEM dimmer. Hence the VDO Dash Light Dimmer will save not only costly parts replacement, but more importantly a possible fire in the dashboard. FITTING INSTRUCTIONS 1. Locate a convenient mounting place in the instrument panel or under the dash near the fuse panel and mount the 97135840 Dash Light Dimmer. Screws (3/16” or 5mm), double sided tape, or Silastic are all acceptable. Orientation is not critical. 2. This module can become quite hot during normal operation and requires ventilation space around it for cooling. Do not mount in areas of high ambient temperature. 3. Connect the “+” terminal (Term. No. 2) on the control module to a suitable positive source, via a 5 amp fuse.. This must be live whenever the dash lights are on. Usually this will go to battery positive. 4. Connect the “ – ” terminal (Term. No. 1) to a good earth or ground connection. 5. Connect terminal no. 5 to your input signal. This will be a parallel connection to the existing wiring from the dimmer to the dash lights. 6. Connect the output terminal (Term’s No. 7 or 8) as required to the new lamp circuits. Note: maximum output is 3 Amps at 12/24Vdc, ie: 36 Watts. Refer to the Connections and Wiring Diagram sections. NOTE: This module is designed as a universal unit to suit as many automotive type applications as possible. However there may be some systems where the input or output signals are not compatible with this unit. The manufacturer is not responsible for incorrect fitting or damage caused by or during the fitting of this module. CONNECTIONS Terminal connections are as follows… Term no. 1 = Negative or Ground, 0Vdc Term no. 2 = +12/24Vdc Battery, or positive when dash lights are on. Term no. 3, 4 = N/C Term no. 5 = Input Signal, variable voltage from existing dimmer circuit. Term no. 6 = N/C Term no. 7 or 8 = Output Signal, square wave, variable duty cycle (approx 50 – 100%) Maximum current 3 Amps at 12/24Vdc Page 1 WIRING DIAGRAM 97135840 – WIRING DIAGRAM Fuse: 3 – 5 Amp +12/24Vdc = on when illumination lamps are required on. Output = 12/24Vdc, Max 36 Watts 2 1 4 3 6 5 8 7 Alternative output connection. Neg, Ground – Existing dimmer circuit output SETTING 1. 2. 3. 4. The unit is preset to follow the voltage on the input terminal within an average +/- 2 Vdc. No setting is necessary. This unit is designed for 12/24Vdc negative ground systems, for other systems contact VDO Australia. A modification is available to use this unit as a stand alone dimmer control. The modification allows the unit to be used for independently controlling up to a maximum of 36 Watts with a separate potentiometer. No original dimmer circuit is required. For further information contact VDO Australia. 5. This unit is usually connected to manufacturers wiring harnesses, where the plug and terminals are already supplied. If the plug and terminals are required please order under the appropriate VDO part numbers. SPECIFICATIONS Dimensions: Mounting: Voltage: Current: Output rating: 68 x 30 x 73mm deep, overall box dimensions. Hole centres…83mm, mounted height…35mm, box with plug & wiring allow min 110mm. 12/24 Vdc negative ground. 10mA at no output – 45mA + Load at full output. Square wave at ~ 50 – 100% duty cycle, Maximum 36Watts at 12/24 Vdc. For any queries, application data or technical information call your supplier or Continental Pty Ltd on 03 9468 1151 http://vdo.net.au 97135840_r3.doc rev: 23/03/09 Printed 05/07/11 Page 2