* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Installation Instructions
Current source wikipedia , lookup
Transformer wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Three-phase electric power wikipedia , lookup
Electrical substation wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Power engineering wikipedia , lookup
Electric battery wikipedia , lookup
Stray voltage wikipedia , lookup
Audio power wikipedia , lookup
Solar micro-inverter wikipedia , lookup
History of electric power transmission wikipedia , lookup
Surge protector wikipedia , lookup
Integrating ADC wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Amtrak's 25 Hz traction power system wikipedia , lookup
Power inverter wikipedia , lookup
Rechargeable battery wikipedia , lookup
Transformer types wikipedia , lookup
Alternating current wikipedia , lookup
Schmitt trigger wikipedia , lookup
Voltage regulator wikipedia , lookup
Voltage optimisation wikipedia , lookup
Power supply wikipedia , lookup
Mains electricity wikipedia , lookup
Buck converter wikipedia , lookup
DPS3 Power Supply/Charger Overview: DPS3 power supply/charger converts low voltage AC input into 6VDC, 12VDC or 24VDC @ 2.5A of continuous supply current (see specifications). This general purpose power supply has a wide range of applications for access control, security and CCTV system accessories that require additional power. Specifications: Visual Indicators: Input: • 6VDC or 12VDC output - use TP1640; 24VDC output - use T2428100. • AC input and DC output LED indicators. Output: • Extremely compact design. • Includes battery leads. • Snap Track compatible (order Altronix model number ST3). Features: • 6VDC, 12VDC or 24VDC selectable output. • 2.5A continuous supply current. • Filtered and electronically regulated output. • Short circuit and thermal overload protection. Board Dimensions (L x W x H approx.): Battery Backup: 3.5” x 3” x 2” (88.9mm x 76.2mm x 50.8mm). • Built-in charger for sealed lead acid or gel type batteries. • Automatic switch over to stand-by battery when AC fails. • Maximum charge current 0.35A. • Battery short circuit protection (circuit breaker). Voltage Output/Transformer Selection Table: Switch Position Transformer Requirements (Recommended Altronix Part #’s) 1 2 6VDC ON OFF 16VAC / 40VA (TP1640) 12VDC OFF OFF 16VAC / 40VA (TP1640, T24130 or T2885) 24VDC OFF ON 28VAC / 100VA (T2885) Note: Transformers with higher VA ratings may be used for all output voltages above as long as you do not exceed 28VAC or 45VDC. Output Voltage Installation Instructions: The DPS3 should be installed in accordance with The National Electrical Code and all applicable Local Regulations. 1. Mount the DPS3 in desired location. 2. Set DC output voltage with switches (refer to Voltage Output/Transformer Selection Table). 3. Connect proper transformer to terminals marked [AC] (Voltage Output/Transformer Selection Table). Use 18 AWG or larger for all power connections (Battery, DC output). Keep power-limited wiring separate from non power-limited wiring (115VAC / 60Hz Input, Battery Wires). Minimum 0.25” spacing must be provided. 4. Measure output voltage before connecting devices. This helps avoiding potential damage. 5. Connect devices to be powered to terminals marked [+ DC ---]. 6. When the use of stand-by batteries is desired, they must be lead acid or gel type. Connect battery to the terminals marked [+ BAT ---] (battery leads included). Use two (2) 12VDC batteries connected in series for 24VDC operation. Note: When batteries are not used, a loss of AC will result in the loss of output voltage. LED Diagnostics: Red (DC) ON ON OFF OFF Green (AC) ON OFF ON OFF Power Supply Status Normal operating condition. Loss of AC. Stand-by battery supplying power. No DC output. Short circuit or thermal overload condition. No DC output. Loss of AC. Discharged or no battery present. Terminal Identification: BKLYN, NY 11220 ST3 Drawing: 0.875” 22.2mm 12, 24 VDC SMP3 6,POWER SUPPLY SW1 SW2 6V ON OFF 12 V OFF OFF 24 V OFF ON 0.625” 15.9mm ON ALTRONIX CORP. DPS3 - Board Drawing: 0.125” 3.2mm 0.3125” (7.9mm) SW1 SW2 3.4375” 87.3mm 3.25” 82.55mm 2.75” 2.6875” 68.26mm 69.85mm AC DC + DC -- + BAT -- AC AC Terminal Legend Function/Description Low voltage AC input (Voltage Output/Transformer Selection Table). For 6VDC output use 16VAC or higher with 24VA power rating or higher. AC /AC For 12VDC output use 16VAC or higher with 40VA power rating or higher. For 24VDC output use 28VAC with 85VA power rating or higher. Caution: Do not apply voltages above 28VAC (28VAC is maximum input rating) - DC + 6VDC-12VDC-24VDC @ 2.5A continuous power-limited output. + BAT Stand-by battery connections. Maximum charge rate 300mA. Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 website: www.altronix.com, e-mail: [email protected]. Lifetime Warranty, Made in U.S.A. IIDPS3 - Rev. 042803 F21P MEMBER