Download f90 - Audix

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Decibel wikipedia , lookup

Audio power wikipedia , lookup

Music technology (electronic and digital) wikipedia , lookup

Sound reinforcement system wikipedia , lookup

PS Audio wikipedia , lookup

Transcript
f90
Condenser Instrument
Microphone
OVERVIEW
The f90 is a cost effective miniature clip-on condenser microphone used for
drum and percussion applications. The f90 is intended for rehearsal bands,
small clubs, schools and Houses of Worship.
Characterized with a uniformly controlled cardioid polar pattern the f90
provides a rich, full sound at distances of 3-4 inches off the drum head. With a
smooth and accurate response over a frequency range of 50 Hz - 18 kHz, the
f90 is lightweight, compact, and simple to use. The flexible gooseneck, along
with the 90 degree angle of the microphone head, puts the microphone
in the proper position for placement directly over the sound source. Final
adjustments can be made by simply twisting or bending the gooseneck into
the desired position.
The f90 operates on phantom voltage of 9-52 Volts and is supplied with a
phantom power adapter, 6’ integrated mic cable, and foam windscreen.
SUPPLIED ACCESSORIES
6’ attached shielded cable with mini XLRf connector
APS910 - 48 V phantom power adapter for use with electret condenser
microphones
WS90 - External foam windscreen for reducing wind, sibilance, and pop
noise
FEATURES
• Low profile condenser clip-on microphone
• Warm, natural sound reproduction
• Tension fit clamping system for rim mounting
• 3 year warranty
APPLICATIONS
• Rack toms, floor toms, snare drums
• Hand percussion
• Cymbals, percussion, brass
APS910
WS90
f90
Transducer Type
Pre-polarized Condenser
Frequency Response
50 Hz - 18 kHz
Polar Pattern
Cardioid
Output Impedance
250 ohms
Sensitivity
8.8 mV / Pa @ 1k
Equivalent Noise Level
29 dB (A-weighted)
Signal to Noise Ratio
65 dB
Maximum SPL
≥135 dB
Power Requirements
9-52 V phantom
Connector
3 pin mini to 3-pin XLRm
(APS910)
Polarity
Positive pressure on diaphragm
produces positive voltage on
pin 2 relative to pin 3
Materials / Finish
Machined Brass Capsule
Gooseneck
Flexible Steel
Weight
170 g / 6 oz
Length
147 mm / 5.1 in
OPERATION AND MAINTENANCE
DIMENSIONS (mm)
Lo
The f90 is a low impedance microphone and should be plugged into
a “mic level” input on your console, mixer, or recording device. The
f90 requires phantom power and will NOT operate without phantom
power voltage (9 - 52 Volts) which is available on most professional
mic preamps and mixing devices. Avoid plugging or unplugging the
microphone from the PA system unless the channel is muted or the
volume of the system turned down. Failure to do so may result in a
loud “popping” noise which could seriously damage the speakers in the
PA system.
APS910 phantom power supply: Note that the mini XLRf
connector at the end of the f90 mic cable plugs into mini XLRm side
of the APS910 power supply. From there, plug a standard XLR-XLR
microphone cable to complete the connection from the APS910 to the
mixing board.
The f90 is manufactured to exacting specs with roadworthy
construction. However, the capsule is highly sensitive and should be
handled with care. Avoid extreme temperatures and be sure to store
your microphone in the pouch provided when not in use. Moisture
of any kind can adversely effect the sound and performance of your
microphone.
USER TIPS
FREQUENCY RESPONSE
POLAR PATTERNS
The microphone shall be of the condenser type available in a cardioid
polar pattern and shall have a 6’ cable terminating in a mini-XLR female
connector. The microphone shall be provided with a remote cylindrical phantom power adapter that will allow the microphone to operate between 9 - 52 volts phantom power. The microphone shall have
a sensitivity of 8.8 mV / Pa and a nominal impedance of 250 ohms at 1
kHz. The microphone shall have a maximum SPL level of ≥135 dB and
is machined out of brass with a length of 7 mm and a capsule diameter
of 15 mm.
f90
ARCHITECT AND ENGINEER SPECIFICATIONS
SPECIFICATIONS
Hi
Drums: The f90 is designed to clip onto the rim of a drum, drum
suspension system, and some types of stands. The position of the f90
should be 2-3” off the drum head. It is not necessary or desirable to
place the microphone too close to the drumhead.
Miking more than one drum with one mic: The f90 has a wide
cardioid pick-up pattern, which means that it is possible to use
the mic to pick up multiple drums. For example: the mic could be
placed between the snare and the high hat, effectively miking both
instruments. The same could be done for two rack toms.
Percussion: The f90’s integral clamp fits most standard (butcherblock) timbale and conga rims, but a separate stand may be needed to
accommodate curved conga/bongo rims.
Brass: The f90 can be used successfully for saxophone, trumpet, and
trombone. Simply attach the clamp to the bottom part of the bell so
that the mic is pointing in the direction of the bell. Do not try to force
the mic inside the bell as the mic is designed to sound best if it is
slightly off axis.
Further miking techniques may be found at www.audixusa.com.
PRODUCT REGISTRATION
Please register your product online at www.audixusa.com/docs_12/about/product_registration.shtml.
SERVICE AND WARRANTY
This microphone is under warranty for a period of 3 years to be free of defects in material and workmanship. In the event of a product failure due to materials or workmanship, Audix will
repair or replace said product at no charge with proof of purchase. Audix does not pay or reimburse shipping costs for warranty repairs or returns. The warranty excludes any causes other
than manufacgturing defects, such as normal wear, abuse, environmental damage, shipping damage or failure to use or maintain the product per the supplied instructions. No Implied
Warranties: All implied warranties, including but not limited to implied warranties of merchantability and fitness for a particular purpose are hereby excluded. The liability of Audix, if any,
for damages relating to allegedly defective products shall be limited to the actual price paid by Dealer for such products and shall in no event include incidental or consequential damages
of any kind. Should your microphone fail in any way, please contact the Audix Service departmenet at 503.682.6933. A Return Authorization is required before returning any product.
OTHER THAN THIS WARRANTY, AUDIX MAKES NO WARRANTEIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS, THE USE OF THE PRODUCTS, THE PERFORMANCE OF THE PRODUCTS. AUDIX
SHALL NOT BE LIABLE FOR SPECIAL INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES ARISING FROM OR BASED ON THE SALE, USE, STORAGE OR DISPOSAL OF THE PRODUCTS, AUDIX’S
SERVICE WORK, BREACH OF WARRANTY, BREACH OF CONTRACT. NEGLIGENCE, OR ANY OTHER THEORY OF LIABILITY, EVEN IF AUDIX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
www.audixusa.com
503.682.6933 Fax: 503.682.7114
Audix Corporation 9400 SW Barber St. Wilsonville, OR 97070
ver 2.0 06-15