Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Model 3541 Resistance HiTESTER Page 1 of 3 NEWS RELEASE Introducing the new Model 3541 Resistance HiTESTER Wide Range of Measurements from 0.1µ-Ohm to 110 M-Ohm HIOKI has just released a new advanced resistance meter, Model 3541 Resistance HiTESTER, as a successor to the popular Model 3227 m-Ohm HiTESTER, while widening the range to include high resistance levels. Wide range of measurements at high speed Model 3541 is a resistance tester that covers a wide range of measurements from 0.1µ-Ohm (20 m-Ohm range) to 110.000 M-Ohm (100M-Ohm range), which allows measurement from low to high resistance levels using the same instrument. Four sampling speeds are available for selection: SLOW2, SLOW1, MEDIUM, and FAST. High-speed measurement using the fastest sampling speed of 0.6 ms (about 1670 times/second) is also realized in this new advanced instrument. In addition to a comparator for determining pass/fail and a BIN function for classifying measurements into ranks, Model 3541comes standard with EXT I/O, GP-IB, and RS-232C interfaces to allow easy construction of high-speed automatic lines. Stable measurement with high precision The basic precision is already high at 70 ppm (0.007%). Model 3541 provides a self-calibration function to automatically correct offset voltage and gain drift, and the offset voltage compensation function to reduce the impact of thermo electromotive force, thus enabling stable measurement with high precision. Furthermore, the average function can find the mean of measurements and stabilize the displayed value. Because the instrument incorporates the fourterminal measurement method, influence by the resistance of measurement leads and contact resistance is at an absolute minimum. Two types of temperature correction functions Model 3541 comes with temperature correction functions to convert a resistance value that vary according to the ambient temperature, to the resistance value of any temperature, and then display the value. The temperature coefficient can be set as desired, and correction using the Pt sensor or the thermometer that comes with analog output is possible. Also, Model 3541 can convert measured resistance value to temperature and then display the temperature change. Additional functions are low-power measurement, measurement fault detection, and statistical calculation functions. Model 9670 (option) can be used to print measurement values and calculation results. Product Overview The new Model 3541, successor to the existing Model 3227 that offers low resistance measurements, is now available. With Model 3541, the smallest resolution has been improved by 100 times to 0.1µ-Ohm, and the measurement range been largely expanded to up to 110.000 M-Ohm. Also, the sampling speed has been significantly increased from 90 times/second to 1670 times/second, and the basic precision has also been raised by about 10 times. Furthermore, Model 3541 now comes with a self-calibration function, offset voltage compensation function, and http://www.hioki.co.jp/eng/newproduct/3541/3541_e.html 04/06/21 Model 3541 Resistance HiTESTER Page 2 of 3 measurement fault detection function, making stable measurement at high speed and high precision possible. Major Features Wide measurement range - measurements from 0.1µW (20 m-Ohm range) to 110.000 M-Ohm (100M-Ohm range) can be performed using the same instrument. High-speed, high-precision measurement - basic precision is high at 70 ppm (0.007%), enabling high-speed measurement at 0.6 ms (about 1670 times/second) Comparator - compare a measurement value with the pre-set upper and lower values to determine where the measurement value falls within the range; the result is then displayed and output BIN function - measured objects can be classified into a maximum of 10 ranks (BIN0 to BIN9), according to a pre-set range; results are displayed and output. Store up to 30 sets of measurement conditions - including settings for comparator and BIN measurements, up to 30 sets of measurement conditions can be stored and recalled by just selecting a setting number, so setting conditions can be changed quickly. Settings can also be accessed by remote control. Two types of temperature correction functions - convert and display resistance values that vary according to the ambient temperature, to the resistance value of any temperature. Use with HIOKI Model 9451 Temperature Probe (Pt sensor) or standard thermometers that come with analog output (infrared thermometer) Convenient Temperature Conversion Function for Motor Coil Verification - Temperature increase is obtained and displayed by converting resistance measurements and ambient temperature - especially useful for verifying motor windings or coils, where the maximum temperature increase needs to be determined when current is applied Self-Calibration - Consistent accuracy is maintained by automatic correction of internal circuit offset voltage and gain drift. Self-calibration is applied at every measurement using SLOW1/SLOW2 sampling, and every 30 minutes with FAST/MEDIUM sampling. Self-calibration is also performed at power on, and when measurement conditions are changed. Offset Voltage Compensation - Thermo electromotive force occurs at the contact point of different metals. This force affects measurements, and if large enough, it can result in measurement errors. The offset voltage compensation function minimizes the effect of thermo electromotive force to preserve measurement accuracy. Measurement Fault Detection - Integrity of source and sensor leads and the constant-current supply are continually monitored to ensure measurements with high confidence. When a measurement fault is detected it is indicated on the instrument, and ERR is output from the EXT I/O interface. Multipolar Connector - A sealed shielded, low-thermo electromotive-force multipolar connector (INPUT B) is provided. The excellent noise immunity of this input makes it ideal for high-speed measurements of large resistances, as well as low power measurements. Standard EXT I/O, GP-IB, RS-232C interfaces - externally control measurement start and measurement conditions. Also, the judgment results, BIN, and BCD data can be output externally to facilitate automatic factory line construction. Statistical Calculation Functions - To observe process conditions, the mean (x), maximum (Max), minimum (Min) overall standard deviation (s), standard deviation of sample (s) and process productivity index (Cp: dispersion, CpK: bias) can be calculated using up to the maximum of 30,000 measurement values. Averaging - find the average of the measurements and stabilize the displayed value; count can be set from 2 to 100 Data Printing - Use the optional Model 9670 Printer to print measurement values, and those including judgment results and statistical calculation results. Primary Applications • Resistance measurement of resistors • Coil resistance measurement such as coil, motor, and transformer • Contact resistance measurement such as relay, switch, and connector • DC resistance measurement of chip inductor • Pattern resistance measurement of PCB board For more information, please contact: [email protected] or visit our website at http://www.hioki.co.jp/ http://www.hioki.co.jp/eng/newproduct/3541/3541_e.html 04/06/21 Model 3541 Resistance HiTESTER Page 3 of 3 © Copyright 2004, HIOKI E.E. CORPORATION http://www.hioki.co.jp/eng/newproduct/3541/3541_e.html 04/06/21