Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Distributed firewall wikipedia , lookup
Multiprotocol Label Switching wikipedia , lookup
Zero-configuration networking wikipedia , lookup
Computer network wikipedia , lookup
Policies promoting wireless broadband in the United States wikipedia , lookup
Network tap wikipedia , lookup
Airborne Networking wikipedia , lookup
Wake-on-LAN wikipedia , lookup
Wireless security wikipedia , lookup
LEDs (Power) (RE) Quick Installation Guide On/Off: The extender is on or off. Blinking: The extender is initializing. Blinking green: WPS connection is in progress. Solid green: The extender is connected to the router and is in a good location. Solid orange: The extender is connected to the router, but is too close to the router. Solid red: The extender is connected to the router, but is too far away from the router. Off: No active connection. (2.4GHz) On: The extender is connected to the 2.4GHz wireless network of your main Router/AP. Off: No connection. AC750 WiFi Range Extender Re se Two easy setup options: Option 1: Using WPS (Wi-Fi Protected Setup) Option 2: Using a Web Browser OPTION 1 (5GHz) 7106505625 REV1.0.1 t LE D RE210 On: The extender is connected to the 5GHz wireless network of your main Router/AP. Off: No connection. Using WPS (Wi-Fi Protected Setup) Important: Please use Option 2 if your router does not support WPS. 1 Power On 2 Connect A. Press the WPS button on your router/AP and immediately press the RE button on your extender. The RE LED should change from blinking to a solid state after about 1 minute, indicating that WPS connection is successful. If not, please use Option 2. e Pow r Plug the extender into an electrical outlet near your router, and wait until the Power LED is lit and solid green. RE er Pow RE RE For more information about using WPS on your router, please refer to the router manufacturer's user guide. r Powe B. If you are connecting the extender to a dual-band router, but only is on, repeat step A to connect the other band. 2.4GHz or 5GHz LED 3 Relocate A. Plug the extender into an electrical outlet about halfway between your router and the Wi-Fi dead zone. B. Wait about 1 minute until the and stay solid. Main Network Extended Network RE LED is lit Solid green Solid red Solid orange Good connection Too far away from the router Too close to the router 5GHz 2.4GHz Ideal Range Extender Placement Both 2.4GHz and 5GHz extended networks share the same SSID (network name) and password as your main network. Choose a location away from Bluetooth devices and other household electronics, such as cordless phone, microwave, and baby monitor, etc., to minimize signal interference. Enjoy! Keep away from Entertainment Adapter The Range extender can be used as a wireless adapter to connect any Ethernet-enabled device, such as a Blu-ray player, game console, DVR, or smart TV, to your wireless network. First, connect the extender to your Wi-Fi network by following the instructions in Option 1 or Option 2, then connect an Ethernet-enabled device to the extender using an Ethernet cable as shown in the diagram on the right. Ethernet Connection Smart TV Game Console Desktop Router OPTION 2 Using a Web Browser 1 Power On 2 Connect Wired: Disconnect your computer from all wireless networks. Connect the Range Extender to your computer via an Ethernet cable. Plug the extender into an electrical outlet near your router, and wait until the Power LED is lit and solid green. or Wireless: Disconnect the Ethernet (wired) connection to your computer. Click the Wi-Fi icon on the taskbar and connect to the extender's network (e.g. TP-LINK_Extender_2.4GHz or _5GHz ). No password is required to connect the first time. Not connected Connection are available Wireless Network Connection RE TP-LINK_Extender_XXGHz r Powe 3 Connect automatically √ Connect 4 Configure Login Launch a web browser and type http://tplinkrepeater.net in the address field. Use admin (all lowercase) for both Username and Password to log in. Follow the Quick Setup Wizard to manually configure the Range Extender. A. On the Start screen, click Next. Start Choose Region B. Choose your region from the Region drop-down list, and click Next. Wireless Settings Review Settings Start Choose Region Wireless Settings Review Settings Main Router/AP Network Status: http://tplinkrepeater.net WiFi Network Name_2.4GHz: N/A WiFi Network Name_5GHz: N/A Connection Status: Region: Disconnected Please click Next to set up the Range Extender or click Exit to manually configure the device by yourself. Username: admin Password: admin Exit Login Cancel Choose Region Exit Wireless Settings √ SSID Signal MAC Review Settings Channel Security TP-LINK_2.4GHz_XXX 00-0A-EB-74-06-06 1 WPA-PSK TP-LINK_XXX 0C-72-2C-B3-A5-2C 1 WPA-PSK Start Choose Region Main Router/AP Network (2.4GHz) Main Router/AP WiFi Network Name(SSID): Main Router/AP MAC Address(BSSID): WiFi Security Option: Fill in the WiFi Password of your Main Router/AP: Range Extender Network (XXGHz) Range Extender WiFi Network Name(SSID): Set SSID and MAC Manually Rescan Back Next E. Repeat step C and D to extend the 5GHz wireless network. Start Choose Region Main Router/AP Network (5GHz) Main Router/AP WiFi Network Name(SSID): Main Router/AP MAC Address(BSSID): WiFi Security Option: Fill in the WiFi Password of your Main Router/AP: Range Extender Network (XXGHz) Range Extender WiFi Network Name(SSID): Back 5 Relocate Wireless Settings Next D. Enter the main router’s Wi-Fi password and either choose Copy from Main Router/AP or Customize to create a new name for the 2.4GHz extended network, then click Next. Available Wireless Networks (2.4GHz): 24 Choose Please select your own region to prevent illegal usage against the local law. Next C. Select your router’s 2.4G wireless network name (SSID) and click Next. If the SSID is hidden, select the Set SSID and MAC manually option. Start Please Select Your Region Review Settings TP-LINK_5GHz_XXX 00-0A-EB-74-06-06 Most Secure(WPA-PSK/WPA2-PSK) 123456789 Copy from Main Router/AP TP-LINK_5GHz_XXX TP-LINK_5GHz_XXX_EXT Customize Next Wireless Settings Review Settings TP-LINK_2.4GHz_XXX 00-0A-EB-74-06-06 Most Secure(WPA-PSK/WPA2-PSK) 123456789 Copy from Main Router/AP TP-LINK_2.4GHz_XXX TP-LINK_2.4GHz_XXX_EXT Customize Back Next F. Verify your Wireless Settings and click Finish. Both 2.4GHz and 5GHz LEDs should turn on and stay solid green. Start Choose Region Wireless Settings Wireless Setting Main Router/AP WiFi Network Name (2.4GHz): Main Router/AP WiFi Network Name (5GHz): Range Extender WiFi Network Name (2.4GHz): WiFi Security Option: WiFi Password: Range Extender WiFi Network Name (5GHz): WiFi Security Option: WiFi Password: Review Settings TP-LINK_2.4GHz_XXX TP-LINK_5GHz_XXX TP-LINK_2.4GHz_XXX_EXT Most Secure (WPA/WPA2-PSK) 123456789 TP-LINK_5GHz_XXX_EXT Most Secure (WPA/WPA2-PSK) 123456789 Export Settings Back Finish Refer to Step 3 of Option 1 to relocate your Range Extender. Main Network Both 2.4GHz and 5GHz extended networks share the same Wi-Fi password as your main network, but may have different wireless network names if you customize the names during the configuration. Extended Network 5G 2.4G Troubleshooting and Support 1 My router has no WPS button, how do I connect the Range extender? Your router does not support WPS, please use Option 2 to set up the extender. 2 How do I restore the extender to its factory default settings? While the extender is plugged into an electrical outlet, press and hold the Reset button until all the LEDs turn on momentarily, then release the button. 3 Why does the RE LED not change to a solid state after completing Option 2? • You may have entered the incorrect Wi-Fi password of your main network during the configuration. Please log into the Extender's web-based interface to check the password and try again. 4 What do I do if I cannot access the Extender’s web-based interface? • Make sure your computer is connected to the extended network. • Make sure your computer is set to obtain an IP address automatically. • If the RE LED still does not change to a solid state, please reset the extender and go through the configuration again. ©2015 TP-LINK