Download PAC 530 Output Controller

PAC520 - Input Controller
1
Input Controller | Overview
The Input Controller (PAC520) is an advanced, multi-purpose controller that provides an interface
between the input devices used to monitor a facility and an Access and Alarm Server (PAC500)
The Input Controller (PAC520) provides the local connection on an RS-485 network between an
Access and Alarm Server (PAC500) using standard alarm or CAT5 cable and the devices used to
monitor and control different devices, including alarms, motion detectors, temperature sensors and
other associated devices.
Twenty user configurable inputs are available supporting Normally Open (NO) or Normally Closed
(NC), with optional supervision via three or four state monitoring. Two 2-Amp output control relays
are configurable as latched, momentary, toggling or pulsing allowing peripheral devices like strobes
or buzzers to be installed.
2
Input Controller | Key Features
The PAC520 advanced design features the following:
20 programmable inputs
2 programmable Form-C 2A output (configurable as latched, momentary, toggling or pulsing)
10.5VDC to 28VDC operating voltage
Supervised (configurable as Normally Open (NO) or Normally Closed (NC) with optional 3 or 4
state supervision) or non-supervised contacts
Status LEDs show the state of all Inputs and Outputs and system status
Local anti-tamper input
Over-ride support
Mains status monitored and reported
Flash upgradeable firmware
One-Touch™ testing mode
3
Input Controller | Device Support
The Input Controller (PAC520) communicates with the system via one of the
2 available RS-485 channels provided by an Access and Alarm Server (PAC500), these
channels are encoded to safeguard network security.
When an input device that is connected to the PAC520 changes state, the PAC520 registers
this change and sends the data to the PAC500. The PAC500 processes this and sends a
message to the Stanley PAC Host system so the Alarm Handling mechanism can respond as
necessary.
A wide range of input devices are supported. For example:
Duress buttons
Arm/Disarm keyswitch
PIR sensors
Elevator button monitor
Temperature alarm
Door monitor
Emergency exit
4
PIR Sensor
Input Controller | Architecture
5
Input Controller | One-Touch
™
Installation Mode
To speed up trouble shooting and ensure error-free installation, One-Touch™ mode enables
the controller functionality to be tested at the controller by just pressing a single button.
There are two test modes:
Active Mode
Used during system configuration to enable a walk test by a
single person. This is achieved by use of latching LED status
which indicate the first change in input condition.
View Mode
Used on a configured system to check the condition of inputs
by using on-board LEDs. The LED display indicates changes
of input state, so alarm and tamper circuits may be walk
tested with one person to perform the walk test and the
second to monitoring LED changes.
One-Touch™ Button
6
Input Controller | Port Layout
7
Input Controller | Cabling
Stanley PAC’s architecture includes a data communication protocol to interface hardware with software,
as well as the cable network to facilitate the data transmission. This architecture enables you to freely
choose:
Centralized or ‘Home Run’ Architecture
Controllers, power supplies, input, output and door controller modules
are located in a central location.
The advantage of this approach includes the ability to monitor and
protect access to this central location and enables a service technician
to troubleshoot components from a single position. This architecture
often requires a large quantity of cable to be installed.
Distributed Architecture
Controllers, power supplies, input, output and door controller modules are located in close proximity to
the access device.
Advantages of this approach includes a reduction of cable quantities required. The door or input/output
controller is generally installed in a locked, tamper switched enclosure above the finished ceiling on the
secure side of the controlled door.
Both home run and distributed have their advantages and disadvantages. Bosch authorised resellers are
a valuable asset in determining which architecture is best suited for the operation and maintenance a
particular system.
8
Input Controller | DIN-Rail Enclosures
A range of metal DIN-Rail enclosures are available to house the
PAC500, PAC512, PAC520, PAC530 and Power Supply Units.
Metal Cabinets available:
Four-way
H: 15.69 in. L: 20.47 in. D: 3.74 in.
(H: 500 mm L: 520 mm D: 95 mm)
Six-way
H: 27.56 in. L: 19.69 in. D: 3.74 in.
(H: 700 mm L: 500 mm D: 95 mm)
Each cabinet is lockable
9
Input Controller | Power Supplies
Durable and reliable power supply units able to meet demands in any environment where
consistency of performance is crucial.
All PSU’s are supplied with DIN-Rail mounts
for easy installation.
Power Supply Options:
10
3AMP
Single Output at 12VDC with charging cables
7AMP
Single Output at 12VDC or 24VDC
Input Controller | Flash Firmware
Flash memory allows the easy upgrading of the PAC520 firmware.
Enables firmware updates to be downloaded
Upgradeable via the Stanley PAC Administration Software
11
Input Controller | Specifications
The following are the physical and environmental
specifications for the PAC520:
Dimensions -
7.3" x 5.1" x 5.1"
Temperature -
(125mm x 180mm x 60mm)
-10oC to 55oC - operating
(14°F to 131°)
-25oC to 80oC - storage
(9°F to 176°)
Humidity
0% to 85% RH non-condensing
Mount
DIN Rail Mount (removable) or
Boxed in metal enclosure
12
Summary
The Input Controller (PAC520) has been designed to provide input flexibility for a facility of any
size and is a powerful component of any Stanley PAC access control installation.
It provides the local connection between an Access and Alarm Server (PAC500) using standard
alarm or CAT5 cable over a RS-485 network and the devices used to monitor and controls
different devices, including alarms, motion detectors, temperature sensors and other associated
devices.
Twenty user inputs are configurable as Normally Open (NO) or Normally Closed (NC), with
optional supervision via three or four state monitoring. Two 2-Amp outputs are configurable as
latched, momentary, toggling or pulsing allowing peripheral devices like strobes or buzzers to be
installed to enhance the security of an installation.
13