* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download AL600ULXD Power Supply/Charger
Survey
Document related concepts
Variable-frequency drive wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Stray voltage wikipedia , lookup
Power engineering wikipedia , lookup
Solar micro-inverter wikipedia , lookup
Three-phase electric power wikipedia , lookup
Power inverter wikipedia , lookup
History of electric power transmission wikipedia , lookup
Voltage optimisation wikipedia , lookup
Alternating current wikipedia , lookup
Schmitt trigger wikipedia , lookup
Mains electricity wikipedia , lookup
Power electronics wikipedia , lookup
Buck converter wikipedia , lookup
Electric battery wikipedia , lookup
Transcript
AL600ULXD Power Supply/Charger Overview: The AL600ULXD power supply converts a 115VAC or 230VAC / 50/60Hz input to a 12VDC or 24VDC non powerlimited output (see specifications). Specifications: Supervision: Agency Listings: • UL Listed for Standard for Safety Access Control System Units (UL 294), Power Power Supplies for Fire-Protective Signaling Systems (UL 1481). • CE European Conformity. • AC fail supervision (form “C” contacts). • Low battery supervision (form “C” contacts). Input: • Low battery disconnect. • Unit is complete with power supply, grey enclosure, cam lock and transformer. • Battery leads included. • 115VAC 60Hz, 1.9A or 230VAC 60Hz 0.95A. Output: • 12VDC or 24VDC selectable output. • 12VDC or 24VDC @ 6A supply current. • Filtered and electronically regulated output. • Short circuit and thermal overload protection. Battery Backup: • Built-in charger for sealed lead acid or gel type batteries. • Automatic switch over to stand-by battery when AC fails. • Maximum charge current 0.7A. Visual Indicators: • AC input and DC output LED indicators. Features: Enclosure Dimensions (H x W x D approx.): 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm). - Accommodates up to two (2) 12VDC/12AH batteries. AL600ULXD: Grey Enclosure. AL600ULXDR: Red Enclosure. Power Supply Voltage Output Selections: Output 12VDC 24VDC Switch Position SW1 ON SW1 OFF Stand-by Specifications: Output 12VDC / 40AH Battery 4 hr. of Stand-by and 5 min. of Alarm Stand-By = 6.0A Alarm = 6.0A 24VDC / 12AH Battery ------------ 24VAC / 40AH Battery Stand-By = 6.0A Alarm = 6.0A 24 hr. of Stand-by and 5 min. of Alarm Stand-By = 1.0A Alarm = 6.0A Stand-By = 200 mA Alarm = 6.0A Stand-By = 1.0A Alarm = 6.0A 60 hr. of Stand-by and 5 min. of Alarm Stand-By = 300 mA Alarm = 6.0A -----------Stand-By = 300 mA Alarm = 6.0A Installation Instructions: The AL600ULXD should be installed in accordance with article 760 of The National Electrical Code or NFPA 72 as well as all applicable Local Codes. 1. Mount the AL600ULXD in the desired location. 2. Connect input power from a separate unswitched AC circuit to the transformers. Secure green wire lead to earth ground. (Fig. 1). For 115VAC input:Connect Yellow and White leads from transformer primary to neutral. Connect Blue and Black leads from transformer primary to line (Fig. 2). For 230VAC input:Connect Blue and Yellow leads of transformer 1 together. Connect Blue and Yellow leads of transformer 2 together. Connect White lead from both transformers to neutral. Connect Black lead from both transformers to line (Fig. 3). Keep power-limited wiring separate from non power-limited wiring (115VAC 50/60Hz or 230 50/60Hz Input, Battery Wires). Minimum 0.25” spacing must be provided. AL600ULXD - 1 - 4. 5. 6. 7. Measure output voltage before connecting devices. This helps avoiding potential damage. Connect devices to be powered to the terminals marked [+ DC –] (Fig. 1). For Access Control applications batteries are optional. When batteries are not used, a loss of AC will result in the loss of output voltage. When the use of stand-by batteries is desired, they must be lead acid or gel type. Connect battery to the terminals marked [+ BAT –] (Fig. 1) (battery leads included). Use two (2) 12VDC batteries connected in series for 24VDC operation. Connect appropriate trouble reporting devices to AC Fail & Low battery (Fig. 1) supervisory relay outputs marked [NC, C, NO]. Use 22 AWG to 18 AWG for AC Fail / Low Battery reporting. AC Failure will report in 5 minutes. For a 6 hour delay on reporting cut resistor R1 (Fig. 1). Maintenance: Unit should be tested at least once a year for the proper operation as follows: Output Voltage Test: Under normal load conditions, the DC output voltage should be checked for proper voltage level (Power Supply Voltage Output Selection Chart). Battery Test: Under normal load conditions, check that the battery is fully charged, check specified voltage both at the battery terminal and at the board terminals marked [+ BAT –] to ensure that there is no break in the battery connection wires. Note: Maximum charging current under discharges is 0.7A. Note: Expected battery life is 5 years; however, it is recommended changing batteries in 4 years or less if needed. Fig. 1 Fig. 2 ON 3 2 BLUE BLACK YELLOW 4 1 XFMR XFMR WHITE 5 OFF = 24V SW1 ON = 12V 115VAC input 50/60 Hz, 1.9A LINE NEUTRAL 230VAC input 50/60 Hz, 0.95A Input 115VAC115VAC Input Fig. 3 2 1 WHITE 3 BLUE 4 YELLOW BLACK 5 Green Lead (ground) 230VAC Input 230VAC Input - 2 - AL600ULXD LED Diagnostics: Red (DC) ON ON OFF OFF Green (AC) ON OFF ON OFF Power Supply Status Normal operating conditions. Loss of AC. Stand-by battery supplying power. No DC output. Loss of AC. Discharged or no stand-by battery. No DC output. Terminal Identification: Terminal Legend Function/Description AC / AC Low voltage AC input (28VAC / 200VA). Two (2) Altronix part # T2885D. + DC – 12VDC / 24VDC @ 6A continuous non power-limited output. Used to notify loss of AC power, e.g. connect to audible device or alarm panel. AC FAIL Relay normally energized when AC power is present. NC, C, NO Contact rating 1A @ 28VDC Low Battery NC, C, NO + BAT – AL600ULXD Used to indicate low battery condition, e.g. connect to alarm panel. Relay normally energized when DC power is present. Contact rating 1A @ 28VDC. Stand-by battery connections. Maximum charge rate 0.7A. - 3 - Enclosure Dimensions (H x W x D approximate): 15.5” x 12” x 4.5” (393.7mm x 304.8mm x 114.3mm) 1.5” (38.1mm) 4.615” (117.22mm) 4.615” (117.22mm) 1.5” (38.1mm) 1.75” (44.45mm) 1.375” (34.925mm) 1.125” (28.575mm) 1.25” (31.75mm) 4.5” (114.3mm) 12.23” (310.64mm) 1.1” (27.94mm) 0.91” (23.114mm) 1.5” (38.1mm) 4.5” (114.3mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.91” (23.114mm) 2.0” (50.8mm) 1.5” (38.1mm) 15.5” (393.7mm) 2.0” (50.8mm) 5.0” (127.0mm) 5.0” (127.0mm) 1.1” (27.94mm) 1.25” (31.75mm) 0.79” (20.06mm) 1.25” (31.75mm) 1.75” (44.45mm) 1.5” (38.1mm) 4.615” (117.22mm) 4.615” (117.22mm) 1.5” (38.1mm) Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 web site: www.altronix.com, e-mail: [email protected]. Lifetime Warranty, Made in U.S.A. IIAL600ULXD - Rev. 013103 - 4 - E17P MEMBER AL600ULXD