* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Sense amplifiers are used to translate this small voltage signal to a
Survey
Document related concepts
Stray voltage wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Buck converter wikipedia , lookup
Shockley–Queisser limit wikipedia , lookup
Voltage optimisation wikipedia , lookup
Rectiverter wikipedia , lookup
Power MOSFET wikipedia , lookup
Alternating current wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Mains electricity wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Transcript
Class- 5 & 6 Overall memory chip organization Static memory circuits using the six-transistor cell Dynamic memory circuits Sense amplifier circuits used to read data from memory cells Learn about row and address decoders Read Only Memory (ROM) Random Access Memory (RAM) refers to memory in a digital system that has both read and write capabilities Static RAM (SRAM) is able to store its information as long as power is applied, and it does not lose the data during a read cycle Dynamic RAM (DRAM) uses a capacitor to temporarily store data which must be refreshed periodically to prevent information loss, and the data is lost in most DRAMs during the read cycle SRAM takes approximately four times the silicon area of DRAM Ch ap 83 Note that the basic building block for this memory is a 128Kb cell The figure shows the block structure of a 256-Mb memory There are sets of column and row decoders that are used for memory array selection The column decoder splits the memory into upper and lower halves The row decoder and wordline drivers bisect each 32-Mb subarray The memory block diagram contains 2M+N storage locations When a bit has been selected, the set of sense amplifiers are used to read/write to the memory location Horizontal rows are referred to as wordlines, whereas the vertical lines are called bitlines Ch ap 85 Inverters configured as shown in the above figure form the basic static storage building block These cross-coupled inverters are often referred to as a latch The circuit uses positive feedback Ch ap 86 With the addition of two control transistors it is possible to create the 6-T cell which stores both the true and complemented values of the data Ch ap 87 Initial state of the 6-T cell storing a “0” with the bitlines’ initial conditions assumed to VDD/2 Conditions after the WL transistors have been turned on Ch ap 88 Final read state condition of the 6-T cell Ch ap 89 Waveforms of the 6-T cell read operation: Wordline capacitive coupling effect Ch ap 810 Reading a 6-T cell that is storing a “1” follows the same concept as before, except that the sources and drains of the WL transistors are switched Note that the delay is approximately 20ns for this particular cell Ch ap 811 It can be seen that not much happens while writing a “0” into a cell that already stores a “0” Microelectronic Circuit Design, 4E McGraw-Hill Ch ap 812 While writing a “0” to a cell that is storing a “1”, the bitlines must be able to overpower the output drive of the latch inverters to force it to store the new condition Ch ap 813 The 1-T cell uses a capacitor for its storage element (data is represented as either a presence or absence of a charge) Due to leakage currents of MA, the data will eventually be corrupted, hence it needs to be refreshed Ch ap 814 Storing a “0” Storing a “1” Ch ap 815 Since the 6-T SRAM provides a large signal current drive to the sense amplifier, it generally has shorter access time as compared to a DRAM The 4-T DRAM cell is an alternative that increases access time, and automatically refreshes itself Ch ap 816 Sense amplifiers are used to detect the small currents that flow through the access transistors or the small voltage differences that occur during charge sharing Ch ap 817 Sense amplifiers are one of the most critical circuits in the periphery of CMOS memories Their performance strongly affects both memory access time, and overall memory power dissipation. 18 As with other ICs today, CMOS memories are required to increase speed, improve capacity and maintain low power dissipation. These objectives are somewhat conflicting when it comes to memory sense-amp design. 19 With increased memory capacity usually comes increased bit-line parasitic capacitance. This increased bit-line capacitance in turn slows down voltage sensing and makes bitline voltage swings energy expensive resulting in slower more energy hungry memories 20 Due to their great importance in memory performance sense amplifiers have became a very large class of circuits Their main function is to sense or detect stored data from a read selected memory cell. 21 22 The memory cell being read produces a current "IDATA" that removes some of the charge(dQ) stored on the pre-charged bitlines. Since the bit-lines are very long, and are shared by other similar cells, the parasitic resistance "RBL" and 23 capacitance "CBL" are large. Thus, the resulting bit-line voltage swing (dVBL) caused by the removal of "dQ" from the bitline is very small dVBL=dQ/CBL Sense amplifiers are used to translate this small voltage signal to a full logic signal that can be further used by digital logic. 24 The need for increased memory capacity, higher speed, and lower power consumption has defined a new operating environment for future sense amplifiers 25 Decreasing memory-cell area to integrate more memory on a single chip reduces the current IDATA that is driving the now heavily loaded bit-line. This coupled with increased CBL causes an even smaller voltage swing on the bit-line. 26 Decreased supply voltage results in smaller noise margins which in turn affect sense amplifier reliability 27 fundamental approaches towards building edge-triggered registers: the master-slave concept and the glitch technique another technique that uses a sense amplifier structure to implement an edge-triggered register 28 Voltage Sense Amplifiers Current-Sensing amplifiers 29 30 SRAM sense amplifiers based on voltage sensing are widely used and established. However, this principle becomes slow for low supply voltages and large memories, since the cell current discharges the bit lines until a considerable voltage swing is reached 31 . Current sensing that uses the cell current directly as a signal keeps the bit line voltages nearly constant and results in fast read operation. This requires a sense amplifier with low input resistance for good impedance matching. The most simple circuit to provide a low input resistance is the common gate stage 32 structure for current sensing has been mentioned. The new concept uses the common gate transistor also as a multiplexer. For this reason the gate voltage is controlled by the select signal SEL of the bit line multiplexer (MUX). 33 A main advantage of current sensing principles compared to voltage sensing is their superior behavior for low voltage operation where the driving cell current becomes very small. 34 Replacement a current-sensing amplifier has been introduced, and its ability to overcome problems associated with voltage sensing may further examined. 35 36 MPC is the precharge transistor whose main purpose is to force the latch to operate at the unstable point previously mentioned Ch ap 837 The same sense amplifier used in the 6-T cell can be used for the 1-T cell in manner shown in the figure Ch ap 838 Obviously it is desired to have a fast access in many DRAM applications. By driving the wordline to a higher voltage (referred to as a boosted wordline), say 5V instead of 3V, it is possible to increase the amount of current supplied to the storage capacitors Ch ap 839 The sense amplifier can definitely be a major source of power dissipation, but by using a clocking scheme, it is possible to reduce the power dissipated, Dummy Cell (DC), Precharge (PC), Latch clock (LC) Ch ap 840 The following figures are examples of commonly used decoders for row and column address decoding NMOS NOR Decoder NMOS NAND Decoder Ch ap 841 Complete 3-bit NAND decoder Ch ap 842 Ch ap 843 ROM is often needed in digital systems such as: ◦ Holding the instruction set for a microprocessor ◦ Firmware ◦ Calculator plug-in modules Ch ap 844 The basic structure of the NMOS static ROM is shown in the figure The existence of an NMOS transistor means a “0” is stored at that address otherwise a “1” is stored Power dissipation is large Ch ap 845 The domino CMOS ROM is one technique used to lower the amount of power dissipation Ch ap 846 Another ROM option is the NAND array ROM which can be directly used with a NAND decoder Ch ap 847 The main problem with these previous ROMs is that they must be designed at the mask level, meaning that it is not a versatile product. To solve this problem, the programmable ROM (PROM) was introduced The standard PROM cannot be erased, so the erasable ROM (EPROM), and later, electrically erasable ROM (EEPROM) were introduced High density flash memories allow for electrical erasure and reprogramming of memory cells Ch ap 848 The reset-set (RS) flip-flop can be easily realized by using either two cross-coupled NOR or NAND gates The RSFF has the following truth tables NOR RSFF NAND RSFF R S Q Q R S Q Q 0 0 Q Q 0 0 Q Q 0 1 1 0 0 1 0 1 1 0 0 1 1 0 1 0 1 1 0 0 1 1 1 1 Ch ap 849 Ch ap 850 Simplified RS flip-flop Ch ap 851 A very important circuit of digital systems is the D-Latch which is used for a D Flip-Flop Whenever clock C goes high in the D-Latch, the data on D is passed through to Q Ch ap 852 By using series D-Latches that latch the data on opposite clock phases, a master-slave D flip-flop can be realized Ch ap 853 The End