* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Electric Part Specification
Radio direction finder wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Oscilloscope history wikipedia , lookup
Analog-to-digital converter wikipedia , lookup
Integrated circuit wikipedia , lookup
Signal Corps (United States Army) wikipedia , lookup
Electrical connector wikipedia , lookup
Crystal radio wikipedia , lookup
Radio transmitter design wikipedia , lookup
Active electronically scanned array wikipedia , lookup
Rectiverter wikipedia , lookup
Battle of the Beams wikipedia , lookup
Printed circuit board wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Analog television wikipedia , lookup
Direction finding wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Regenerative circuit wikipedia , lookup
Cellular repeater wikipedia , lookup
Bellini–Tosi direction finder wikipedia , lookup
Opto-isolator wikipedia , lookup
High-frequency direction finding wikipedia , lookup
GIONEE Service Manual 1 GIONEE CONTENT 1、Mobile Phone Introduction………………………………………………………3 2、Schematics Introduction………………………………………………………….3 2.1 RF circuit……………………………………………………………………..3 2.2 Baseband circuit…………………………………………………………….11 2.3 Power management circuit…………………………………………………13 2.4 Function circuit……………………………………………………………..14 3、Typical fault repair………………………………………………………………28 2 GIONEE 1、Mobile Phone Introduction This phone use MT6589 platform of MTK and support GSM(GPRS)/WCDMA. 2、Schematics Introduction Block Diagram This phone mainly include four parts:RF circuit, baseband circuit, function circuit and IO circuit. Each of them is introduced bellow. 2.1 RF circuit RF circuit include GSM receive circuit, WCDMA receive circuit, GSM transmit circuit and WCDMA transmit circuit. WCDMA+GSM part 2.1.1 GSM receive circuit GSM receive circuit include antenna, RF connector CON703(W+G), RF switch and GSM transmit module U702, GSM radio transceiver module U601 and peripheral circuits. The internal schematic of U702 as bellow. 3 GIONEE RF signal enter phone from antenna. It pass through CON703 and arrive PIN26 of U702. U702 is controlled by U201. The control voltage and signal as bellow. Receive signal from U702 to U1202/U603/U604/U607/U616. Then RF signal will be sent to RFIC U1101. The module of U601 is MT6167. The internal schematic of MT6167: 4 GIONEE The main receive work is done in U601. RF signal enters to U601 from LNA8N/LNA8P, LNA7N/LNA7P, LNA6N/LNA6P and LNA5N/LNA5P. Finally, U601 send 4 paths I/Q signals to CPU U201. 2.1.2 WCDMA receive circuit WCDMA receive circuit include antenna, RF connector CON703, RF switch U702, filter U616 and U607, WCDMA radio transceiver U601 and peripheral circuits. The internal schema of U1201 as bellow. RF signal enter phone from antenna. It pass through CON703 and arrive PIN26 of U702. U1201 can switch from GSM to WCDMA. WCDMA signal arrive at U616 and U607. Receive signal arrive to RFIC U601 from U616 and U607. The module of U601 is MT6167. The internal schematic of MT6167: 5 GIONEE The main receive work is done in U601. RF signal enters to U601 and finally send 4 paths I/Q signals to CPU U201. 2.1.3 GSM transmit circuit GSM transmit circuit include U601, U702, CON703 and antenna. MIC change analog voice signal to analog electric signal. The analog electric signal enter CPU U201. U201 send 67.7KHZ 4 path IQ signals to U601. The internal schematic of RF3233 (U1201): 6 GIONEE U601 send RF signal to PIN9 and PIN10 of U702. Then the signal is sent to antenna from RF connector CON703. The signal is transmitted from antenna. 2.1.4 WCDMA transmit circuit WCDMA transmit circuit include U601, U708/U713, U607/U616, U702, CON703 and antenna. MIC change analog voice signal to analog electric signal. The analog electric signal enter CPU U201. U201 send 4 path IQ(IP, IN, QP, QN) signals to U601. U601 send RF signal through PA U708/U713, duplex U607/U616, antenna switch U702. Transmit signal sent to antenna from RF connector CON703. The signal transmitted from antenna. The internal schematic of 3G-PA: 7 GIONEE GSM part 2.1.5 GSM receive circuit GSM receive circuit include antenna, RF connector CON1701(GSM), RF switch and GSM transmit module U805, GSM radio transceiver module U1704 and peripheral circuits. The internal schematic of U805 as bellow. 8 GIONEE RF signal enter phone from antenna. It pass through CON1701 and arrive PIN15 of U805. U805 is controlled by U201. The control voltage and signal as bellow. Receive signal from U805 to U1705/U1706/U1707/U1708. Then RF signal will be sent to RFIC U1704. The module of U1704 is MT6163. The internal schematic of MT6163: 9 GIONEE The main receive work is done in U1704. RF signal enters to U1704 from LNA2N/LNA2P, LNA7N/LNA7P, LNA6N/LNA6P and LNA4N/LNA4P. Finally, U1704 send 4 paths I/Q signals to CPU U201. 2.1.6 GSM transmit circuit MIC change analog voice signal to analog electric signal. The analog electric signal enter CPU U201. U201 send 67.7KHZ 4 path IQ signals to U601. The internal schematic of RF9802 (U805): 10 GIONEE U1704 send RF signal to PIN2 and PIN4 of U805. Then the signal is sent to antenna from RF connector CON1701. The signal is transmitted from antenna. 2.2 Baseband circuit Baseband circuit mainly include U201 and U501. The module of U201 is MT6589. It’s CPU of phone. The internal schematic: 11 GIONEE U501 is the memory circuit of phone. 16GB EMMC +16GB DDR2 SDRAM. 1.8V voltage supply. EMMC is hard disk similar to PC. When phone is power on, program will be sent to DDR. It can make phone power on fast. The internal schematic: 12 GIONEE 2.3 Power management circuit Power management circuit mainly include PMC IC U301. The module of U301 is MT6320. It provide voltages to baseband, RF part, external IO connectors. The internal schematic: 13 GIONEE 2.4 Function circuit 2.4.1 Motor driver U201 output control signal to motor driver IC U1101. Control pins list: 14 GIONEE The internal schematic: 2.4.2 Receiver, MIC, speaker and headset circuit HSN, HSP/MICP0, MICN0/ HPLP/HPLP, HPRP, MICP0, MICN0 from U301 will be sent to Receiver/MIC/speaker/headset. HPLP signal will be sent to speaker after amplify by AUDIO PA(U401). The internal schematic: 15 GIONEE 2.4.3 BT circuit The module of BT is MTK6628. It’s a FM/BT/WIFI/GPS four in one chip. The internal schematic: 16 GIONEE 17 GIONEE 2.4.4 WIFI circuit The module of WIFI is MTK6628. It’s a FM/BT/WIFI/GPS four in one chip. The internal schematic is same as BT part. The RF connector connects with external antenna. 2.4.5 GPS circuit The module of GPS is MTK6628. It’s a FM/BT/WIFI/GPS four in one chip. The internal schematic is same as BT part. It communicates with CPU through UART3. 18 GIONEE 2.4.6 FM circuit The module of FM is MTK6628. It’s a FM/BT/WIFI/GPS four in one chip. The internal schematic is same as BT part. It’s work is controlled by U201 through UART. Clock signal also provided by U201. 19 GIONEE 2.4.7 IO connector circuit 1) SIM card circuit This phone support dual SIM. SIM1 support GSM/WCDMA, SIM2 only support GSM. The internal schematic: 20 GIONEE 2)LCD and TP connector circuit LCD is connected to PCBA by FPC. The data and control signals are provided byU201. Voltages VDD28_PMU and VDD18_PMU are provided by PMU U201. The internal schematic: The LCD backlight driver U901 is on PCBA. Its output voltage support to 46V.The schematics: 21 GIONEE This phone is designed with capacity touch panel. The touch signal is sent to CPU through IIC connector. The schematics of connector on PCBA: 22 GIONEE 3)Camera connector circuit This phone has two cameras. Camera is controlled by U201. The main camera is connected to PCBA by MIPI. The voltages supply circuit: The front camera is connected to PCBA by CN602. The voltages supply circuit: 4)Keypad and backlight connector circuit There are 6 keys totally, 1 power key, 2 volume keys and 3 touch keys. When keys pressed, interrupt sent to CPU. CPU will identify which key pressed. Keypad connector circuit: 23 GIONEE Power key: The signal is sent to CPU through connector on PCBA. The schematics: The 3 touch panel keys are on capacity touch panel. The signal is sent to CPU through IIC. The schematics: 24 GIONEE The keypad back light is controlled by PUM(U301). Block diagram: 25 GIONEE The keypad light is designed on sub PCBA with BTB connector. The schematics: 5)USB connector circuit This phone uses 5PIN MIRCO USB connector. It support USB2.0(480Mz data transmission). It also can be used for SW download. The USB connector circuit: 6)SENSOR circuit G-SENSOR is mainly used to identify the direction of phone. It supports 3 directions (X, Y, Z) induction. It communicates with CPU through I2C. U301 provide VDD28_PMU and VDD18_PMU to G-SENSOR. 26 GIONEE M-SENSOR is electric compass. It’s used for instructing direction. It supports 3 directions (X, Y, Z) induction. It communicates with CPU through I2C. U301 provide VDD28_PMU and VDD18_PMU to M-SENSOR. 27 GIONEE Light sensor is used for identifying the environment brightness and adjusting the LCD brightness. It can save power. Distance SENSOR is used for identifying the distance between user’s face and phone during a call. If the distance is less than a value, phone will turn off the touch panel and LCD. It can save power and avoid mis-operation. It communicates with CPU through I2C. U301 provide VDD28_PMU and VDD18_PMU to Light-distance SENSOR. 3、Typical fault repair. 1. Download Fail 1)Check the soldering of USB connector CN903.; 2)Check the voltages output by U301. If not correct, solder or replace U301. 3)Check 26MHz output by X601.If it is, check whether the PIN D11 of X601 output 26MHz.If not, check the soldering of X601and U601 4)Check the soldering of U501. 5)Check the soldering of U201. 6)Check TVS diode(VR1102,VR1103,VR1104) whether placed correct. 2. Not power on 1)Download SW. If can’t download, repair it reference 1. 3. No display or display abnormal 1)Check the connection between LCD-FPC and CN902 2)Check the soldering of CN902 3)Check connector of LCD-FPC. 4)Check the voltages output by backlight IC.(about 30 V); 5)Solder or replace U201. 4. Can’t identify SIM card 1)Check the connection between SUB board and Main board. 2)Check the soldering of CON401 3)Check VSIM voltage. If not correct, solder or replace U301.; 4)Solder or replace U301. 28 GIONEE 5. Charging fail 1)Check the soldering of USB connector CN903. 2)Check the soldering of U204 and U210. 3)Solder or replace U301. 4) Check FPC connector is loosen or damaged 6. No ringtone or ringtone abnormal 1) Check the phone setting. If the ringtone be turned off. 2)Re-download SW or Restore to factory setting. 3)Check the shrapnel of speaker. 4)Check the soldering of earphone socket. 5)Check the soldering of AUDIO connect (J1104) 6)Check the soldering of U301. 7)Solder or replace U301 8)Check FPC connector is loosen or damaged 7. Front camera not work 1)Check the connection between front camera and PCBA.; 2)Check the soldering of connector CN602. 3)Check VDD_DVDD_1_5V, VDD_DOVDD_1_8V and VDD_AVDD_2_8V. If not correct, solder or replace U301. 4)Solder or replace U301. 8. Main camera not work 1)Check the soldering of CN601.; 2)Check VDD_DVDD_1_5V, VDD_DOVDD_1_8V and VDD_AVDD_2_8V. If not correct, solder or replace U301. 3)Solder or replace U301. 9. Keypad or side key not work 1)Check the assembly or touch panel. 2)Check the soldering of side key. 3)Check if keypad signal output by U101. If no, solder or replace U201. 4)Solder or replace U201. 10. Receiver not work 1)Check the shrapnel between PCBA and receiver. 2)Solder or replace U301. 11. MIC not work 1)Check the MIC is placed the wrong way 2)Check the soldering of J1003 29 GIONEE 3)Check the soldering of J1005 4)Check FPC connector is loosen or damaged 3)Check the soldering of MIC 4)Check the MIC voltage. If not correct, solder or replace U301. 4)Solder or replace U301. 12. Earphone not work 1)Check the shrapnel between PCBA and earphone. 2)Check the soldering of earphone connector J402. 3)Solder or replace U301. 13. Touch panel not work 1)Check the connection between FPC and connector CN903 2)Check the soldering of CN903 3)Check the touch panel voltage VDD_TP .If not correct, solder or replace U1302. 4)Replace a good CTP 14. BT not work 1)Check the soldering of BT chip U1401. 2)Check the soldering of BT antenna shrapnel J1401,J1402. 3)Check the soldering of antenna switch U1403 4)Check the output of U1505 and U1401. If not correct, solder and replace U1505 and U1401. 4)Solder or replace U201. 15 WIFI not work 1)Check the soldering of WIFI chip U1401. 2)Check the soldering of WIFI shrapnel J1401.J1402 3)Check the soldering of U1403. 4)Check the output of U1505 and U1401.If not correct, solder or replace U1401and U1505 4)solder or replace U201 16. GPS not work 1)Check the soldering of U1401. 2)Check the soldering of GPS shrapnel J1402. 3)Check the antenna switch of U1403. 4)Check the output of U1505 and U1401.If not correct, solder or replace U1401and U1505 4)solder or replace U201 30 GIONEE 17. FM not work 1) Check the soldering of FM chip U1401. 2) Check the soldering of AUDIO socket J402. 3) Check the output of U1505 and U1401.If not correct, solder or replace U1401and U1505 4)solder or replace U201 18. G-SENSOR not work 1)Check the soldering of U1202. 2)Check the Pin voltage(VDD18_PMU,VDD28_PMU) of U1201. if not correct, solder or replace U301 3)solder or replace U201 19. M-SENSOR not work 1)Check the soldering of U1201. 2)Check the Pin voltage(VDD18_PMU,VDD28_PMU) of U1201.if not correct, solder or replace U301 3)solder or replace U201 20. ALS/PS not work 1) Check the soldering of CN1201. 2) Check the connection between ALS/PS FPC and main board connector CN1201 3) Check the output Pin voltage(VDD18_PMU,VDD28_PMU) of U1201.if not correct, solder or replace U301. 4)solder or replace U201 21. MOTOR not work 1)Check the soldering of MOTOR. 2)Check the VIBR_PMU output voltage of MOTOR. If not correct, solder or replace U1101. 3)solder or replace U201 22. GSM no receive signal 1)Check the access soldering between J1202 and CON703. 2)Check the access soldering between ON703 and U702. 3)Check the access soldering between U702 and U601. 4)Check the soldering of U601. 5)Check the soldering of U702 6)Check the control logic VC1,VC2,VC3,if not correct, change U201. 7)Check the U601 power supply voltage Pin AVDD,VDD,VRF. If not correct, change U201 31 GIONEE 8)Check the output 26MHz signal of crystal X601, 9)solder or replace U201 23. GSM no transmit 1)Check the access soldering between J1202 and CON703. 2)Check the access soldering between ON703 and U702. 3)Check the access soldering between U702 and U601. 4)Check the soldering of U601. 5)Check the soldering of U702 6)Check the control logic VC1,VC2,VC3,if not correct, change U201. 7)Check the U601 power supply voltage Pin AVDD,VDD,VRF. If not correct, change U201 8)Check the output 26MHz signal of crystal X601,; 9)solder or replace U201 24. WCDMA no receive 1)Check the access soldering between J1202 and CON703. 2)Check the access soldering between ON703 and U702. 3)Check the access soldering between U702 and U601. 4)Check the soldering of U601. 5)Check the soldering of U702 6)Check the control logic VC1,VC2,VC3,if not correct, change U201. 7)Check the U601 power supply voltage Pin AVDD,VDD,VRF. If not correct, change U201 8)Check the output 26MHz signal of crystal X601,; 9)solder or replace U201 25. WCDMA no transmit 1)Check the access soldering between J1202 and CON703. 2)Check the access soldering between ON703 and U702. 3)Check the access soldering between U702 and U616/U617. 4)Check the access soldering between u708/U713 and U601. 5)Check the soldering of U601. 6)Check the soldering of U702 7)Check the soldering of U708/U713 8)Check the control logic VC1,VC2,VC3,if not correct, change U201. 9)Check the control signal VM1,VM0 of U708/U713, If not correct, change U201. 10) Check the power supply AVDD,VDD,VRF of U601. If not correct, change U601. 11)Check the output 26MHz signal of crystal X601,; 12)Solder or replace U201 32