Survey

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Three-phase electric power wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Electrical substation wikipedia , lookup

Ohm's law wikipedia , lookup

History of electric power transmission wikipedia , lookup

Control system wikipedia , lookup

Scattering parameters wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Stray voltage wikipedia , lookup

Audio power wikipedia , lookup

Voltage optimisation wikipedia , lookup

Islanding wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Tube sound wikipedia , lookup

Current source wikipedia , lookup

Transistor wikipedia , lookup

Alternating current wikipedia , lookup

Wien bridge oscillator wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Amplifier wikipedia , lookup

Voltage regulator wikipedia , lookup

Mains electricity wikipedia , lookup

Schmitt trigger wikipedia , lookup

Rectifier wikipedia , lookup

Solar micro-inverter wikipedia , lookup

Power electronics wikipedia , lookup

Buck converter wikipedia , lookup

Two-port network wikipedia , lookup

Power inverter wikipedia , lookup

CMOS wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Opto-isolator wikipedia , lookup

Current mirror wikipedia , lookup

Transcript
```THE UNIVERSITY OF MICHIGAN - DEARBORN
ELECTRICAL AND COMPUTER ENGINEERING DEPT.
ECE 311 - Electronics
ABET Outcomes Test
Summer, 2003
Dr. H. Kaufman
Five questions
Pg. 1 of 3
Consider the inverter shown in the Figure. A capacitor C = 10pF is connected between the
output and ground. Let VDD = 5V, R = 1kW , Ron = 100W and Voffset = 0.1V. If at time
t =0, VI goes low and neglecting the delay time of the switch, that is, assuming it opens
immediately, find the time for the output to reach 0.5(VOH + VOL).
1.
2.
Design the circuit in the Figure to provide an output voltage of 2.4 volts. Assume that the
diodes available have 0.7 volt drop at 1mA and that DV = 0.1 V/decade change in current.
ECE 311 ABET Outcomes Test Summer 2003
pg. 2 of 3
3. For the common-emitter amplifier shown in the Figure, let VCC = 9V, R1 = 27kW ,
R2 = 15kW , RE = 1.2kW , and RC = 2.2 kW . The transistor has b = 100.
(a) Calculate the DC bias current IE.
(b) Draw the SSAC model for the transistor circuit and calculate any required AC
parameters.
(c) What is the voltage gain vo/vs
(d) What is the input impedance
(e) What is the output impedance.
4.
5.
(a) Draw the CMOS inverter.
(b) What is the required relationship between (W/L)p and (W/L)n for which the transistors
Qn and Qp are said to be matched and the CMOS inverter is made to switch at the
midpoint of logic swing, (i.e. at VDD/2 ) ?
Draw the transfer characteristic for the Class B output stage and circle the region in
which “crossover distortion” occurs.
Assume that Qn and Qp have collector-emitter saturation values VCENsat and VECPsat
respectively.
ECE 311 ABET Outcomes Test Summer 2003
pg. 3 of 3
6. The circuit shown in the Figure is intended to supply current to floating loads (those for which
both terminals are ungrounded) while making the greatest possible use of the available power
supply.
(a) Assuming ideal op amps, sketch the voltage waveforms at nodes B and C for a 1-V
peak –to-peak sine wave applied at A. Also sketch vO.
(b) Assuming that the op amps operate from + 15V power supplies and their output saturates
at + 14 V, what is the largest sine wave output (peak to peak value) that can be
accommodated?
+
+
(c) Give at least four characteristics of an ideal op-amp
(Hint: what is open loop gain, output resistance, bandwidth, current into each input?
(d) What is meant by the term “slew rate”?
```
Related documents