Download KFD2-STV4-2-1 SMART Transmitter Power Supply Connection

SMART Transmitter Power Supply
KFD2-STV4-2-1
Assembly
Features
•
•
•
•
•
•
2-channel signal conditioner
24 V DC supply (Power Rail)
Input 2-wire SMART transmitters
Output 0/1 V ... 5 V
Terminal blocks with test sockets
Up to SIL 2 acc. to IEC 61508
Front view
Removable terminals
green
3
6
1 2
4 5
Function
KFD2-STV4-2-1
This signal conditioner provides the isolation for nonintrinsically safe applications.
LED green:
Power supply
PWR
The device supplies 2-wire SMART transmitters.
It transfers the analog input signal as an isolated voltage
value.
7 8 9
10 11 12
13 14 15
Digital signals may be superimposed on the input signal and
are transferred bi-directionally.
If the HART communication resistance in the loop is too low,
the internal resistance of 250 Ω between terminals 8, 9
and 11, 12 can be used.
Removable terminals
green
Test sockets for the connection of HART communicators are
integrated into the terminals of the device.
Application
The device supports the following SMART protocols:
• HART
• BRAIN
• Foxboro
3
Release date 2017-01-13 10:36
7-
3-
8+
250 Ω
II
9
4+
10-
6-
11+
250 Ω
HART
1+
HART
I
HART
KFD2-STV4-2-1
HART
Date of issue 2017-01-13
228762_eng.xml
Connection
12
14+
15-
24 V DC
24 V DC
Power Rail
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
Pepperl+Fuchs Group
USA: +1 330 486 0002
Germany: +49 621 776 2222
www.pepperl-fuchs.com
[email protected]
[email protected]
Singapore: +65 6779 9091
[email protected]
1
Technical data
KFD2-STV4-2-1
General specifications
Signal type
Analog input
Supply
Connection
Rated voltage
Ripple
Power Rail or terminals 14+, 15Ur
20 ... 35 V DC
within the supply tolerance
Power dissipation
1.8 W
Power consumption
≤ 2.7 W
Input
Connection
terminals 1+, 3-; 4+, 6-
Input signal
0/4 ... 20 mA
Open circuit voltage/short-circuit current
terminals 1+, 3-; 4+, 6-: 22.1 V / 38 mA
Available voltage
≥ 16 V at 20 mA
Output
Connection
terminals 7-, 8+; 10-, 11+
Load
output resistance: 250 Ω
Output signal
0/1 ... 5 V
Ripple
≤ 12.5 mV
Transfer characteristics
Deviation
Influence of ambient temperature
Frequency range
Rise time
at 20 °C (68 °F), 0/1 ... 5 V ≤ 5 mV incl. calibration, linearity, hysteresis, loads and fluctuations of supply voltage
≤ 20 ppm/K
input to output: bandwidth with 1 Vpp signal 0 ... 7.5 kHz (-3 dB)
output to input: bandwidth with 1 Vpp signal 0.3 ... 7.5 kHz (-3 dB)
20 µs
Settling time
200 µs
De-energized delay
20 µs
Galvanic isolation
Input/Output
Input/power supply
Output/power supply
Input/input
Output/Output
basic insulation according to IEC 61010-1, rated insulation voltage 300 Veff
basic insulation according to IEC 61010-1, rated insulation voltage 300 Veff
functional insulation, rated insulation voltage 50 V AC
basic insulation according to IEC 61010-1, rated insulation voltage 300 Veff
functional insulation, rated insulation voltage 50 V AC
Directive conformity
Electromagnetic compatibility
Directive 2014/30/EU
EN 61326-1:2013 (industrial locations)
Conformity
Electromagnetic compatibility
NE 21:2011
Degree of protection
IEC 60529:2001
Protection against electrical shock
EN 61010-1:2010
Ambient conditions
Ambient temperature
-20 ... 60 °C (-4 ... 140 °F)
Mechanical specifications
Degree of protection
IP20
Mass
approx. 100 g
Dimensions
20 x 124 x 115 mm (0.8 x 4.9 x 4.5 inch) , housing type B2
Mounting
on 35 mm DIN mounting rail acc. to EN 60715:2001
Supplementary information
Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be
observed where applicable. For information see www.pepperl-fuchs.com.
Release date 2017-01-13 10:36
Date of issue 2017-01-13
228762_eng.xml
General information
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
Pepperl+Fuchs Group
USA: +1 330 486 0002
Germany: +49 621 776 2222
www.pepperl-fuchs.com
[email protected]
[email protected]
Singapore: +65 6779 9091
[email protected]
2
Technical data
KFD2-STV4-2-1
Accessories
Power feed module KFD2-EB2
The power feed module is used to supply the devices with 24 V DC via the Power Rail. The fuse-protected power feed module
can supply up to 150 individual devices depending on the power consumption of the devices. Collective error messages received
from the Power Rail activate a galvanically-isolated mechanical contact.
Power Rail UPR-03
The Power Rail UPR-03 is a complete unit consisting of the electrical insert and an aluminium profile rail 35 mm x 15 mm. To
make electrical contact, the devices are simply engaged.
Profile Rail K-DUCT with Power Rail
The profile rail K-DUCT is an aluminum profile rail with Power Rail insert and two integral cable ducts for system and field cables.
Due to this assembly no additional cable guides are necessary.
Release date 2017-01-13 10:36
Date of issue 2017-01-13
228762_eng.xml
Power Rail and Profile Rail must not be fed via the device terminals of the individual devices!
Refer to "General Notes Relating to Pepperl+Fuchs Product Information".
Pepperl+Fuchs Group
USA: +1 330 486 0002
Germany: +49 621 776 2222
www.pepperl-fuchs.com
[email protected]
[email protected]
Singapore: +65 6779 9091
[email protected]
3