Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Semiconductor Transistors Homework: Chapter 11 Krane Problems: 13, 14, 15, 16, 17, 23, 28, 33, 34, 35 Due Wednesday Nov. 25th 1 Forward Bias and Reverse Bias Forward Bias : Connect positive of the positive end to positive of supply…negative of the junction to negative of supply Reverse Bias: Connect positive of the junction to negative of supply…negative of junction to positive of supply. 2 PN Junction: Under Bias • Forward Bias: negative voltage on n-side promotes diffusion of electrons by decreasing built-in junction potential higher current. • Reverse Bias: positive voltage on n-side inhibits diffusion of electrons by increasing built-in junction potential lower current. Equilibrium Forward Bias Reverse Bias p-type n-type e– p-type n-type –V e– Majority Carriers p-type n-type +V e– Minority Carriers 3 pn Junction: IV Characteristics Current-Voltage Relationship I I o [e eV / kT 1] Forward Bias: current exponentially increases. Reverse Bias: low leakage current equal to ~Io. Ability of pn junction to pass current in only one direction is known as “rectifying” behavior. Forward Bias Reverse Bias Manifestly not a resistor: V=IR Not Ohm’s law 4 N-channel MOSFET Gate Drain Source n gate oxide insulator p n ID • Without a gate-to-source voltage applied, no current can flow between the source and drain regions. • Above a certain gate-to-source voltage (threshold voltage VT), a conducting layer of mobile electrons is formed at the Si surface beneath the oxide. These electrons can carry current between the source and 5 drain. Metal-Oxide-Semiconductor FET How does it work? There is no conduction between the source and drain normally (VGS = 0) because regardless of what voltage VDS you apply there is a reverse biased PN junction. Even apply a voltage VGS does not appear from the structure to have an obvious effect since it is not even attached - there is a thin SiO2 insulating layer in between! 6 Metal-Oxide-Semiconductor FET(2) However when you apply a positive voltage the oxide behaves like a capacitor since positive charge builds up on one side, there must be an equal and opposite charge on the other side. This charge must come from the substrate. Since it is P-type there are not many electrons but those that are present are all sucked up to the gate oxide. This creates a region that is very thin, but very rich in electrons, converting P-type to N-type locally. This “channel” is enhanced by applying higher positive biases. 7 IG vs. VGS Characteristic Consider the current IG (flowing into G) versus VGS : S IG V + IG G oxide semiconductor D V +DS GS always zero! The gate is insulated from the semiconductor, so there is no significant steady gate current. VGS 8 ID vs. VDS Characteristics Next consider ID (flowing into D) versus VDS, as VGS is varied: S V + G oxide semiconductor ID D V +DS GS ID VGS > VT zero if VGS < VT VDS Above threshold (VGS > VT): “inversion layer” of electrons appears, so conduction between S and D is possible Below “threshold” (VGS < VT): no charge no conduction 9 The MOSFET as a Controlled Resistor The MOSFET behaves as a resistor when VDS is low: Drain current ID increases linearly with VDS Resistance RDS between SOURCE & DRAIN depends on VGS • RDS is lowered as VGS increases above VT NMOSFET Example: ID VGS = 2 V VGS = 1 V > VT VDS IDS = 0 if VGS < VT 10 ID vs. VDS Characteristics The MOSFET ID-VDS curve consists of two regions: 1) Resistive or “Triode” Region: 0 < VDS < VGS VT VDS W ID VGS VT VDS L 2 where k n n Cox k n 2) Saturation Region: VDS > VGS VT kn W 2 VGS VT I DSAT 2 L where kn nCox “CUTOFF” region: VG < VT 11 MOSFET regions of operation Cutoff: VGS <= VT ID = 0 Resistive: ID ~ (VGS – VT)VDS Saturation: ID ~ (VGS – VT)2 12 MOSFET Uses A MOSFET can be used as A linear amplifier: Input voltage applied between gate and source; output voltage appears between source and drain or An electronic switch: Switches between no current conduction between source and drain, and heavy conduction between source and drain as voltage applied between gate and source changes from low to high 13 Importance The transistor is probably the most important invention of the 20th century…. Transistors are central to the Integrated Circuit, and therefore, all electronic devices of the information age, such as: pc’s, cellular phones, ipods, pda’s, intelligent cars and smart buildings……. 14 In the beginning….1936 Mervin Kelly was Bell Lab's director of research. He felt that to provide the best phone service it will need a better amplifier; the answer might lie in semiconductors. He then formed a department dedicated to solid state science 15 1945 Bill Shockley the team leader of the solid state department hired Walter Brattain and John Bardeen. He designed the first semiconductor amplifier, relying on the field effect. The device didn't work, and Shockley assigned Bardeen and Brattain to find out why. 16 1947 Bardeen and Brattain built the point contact transistor. They made it from strips of gold foil on a plastic triangle, pushed down into contact with slab of germanium. http://www.lucent.com/minds/ transistor/history.html http://www.lucent.com/minds/ transistor/history.html 17 1947 cont. 18