Download Cisco certified network associate

CISCO CERTIFIED NETWORK ASSOCIATE
Welcome!
WELCOME!
•
Goal – Cisco Certified Network Associate, Cisco Certified Network Professional, and beyond!
•
About Me
•
Overall view of classes
•
Switching Basics (frames, broadcast / collision domains, arp)
•
Switching advanced (stp, portfast, root bridge, vtp pruning, trunking, port-channels)
•
Routing Basics (static, rip, ospf, eigrp)
•
Routing advanced (route redistribution, changing metrics)
•
Other awesome topics
• NAT, IPv6, Binary / Hex conversion, subnet maths, summarization
• PPP and Frame Relay
•
First interview question
•
Next…Topics to cover today
TOPICS TO COVER
•
Hardware (Where (decent places), what (3550, 3560, or 2950), why (emulation?)
• Cables / cabling needs (Auto MDIX – medium dependent interface crossover)
•
Boot (ROMMON, flash, ROM, RAM, NVRAM, running-config, startup-config), diagnostics
•
Switching Basics
• Models (TCP/IP, versus DoD)
• Frames (hubs, repeaters, flooding, broadcast / collision domains) – examples
• VLANing
• Mac addressing (OUI vey)
• Arp
• CDP
• VTP
•
Next…Hardware
HARDWARE
•
Where (decent places)
•
•
http://www.certificationkits.com/
What to buy (3550, 3560, or 2950)
•
CCNA – 2 2950, or 3550, 2900 series (RAM!)
•
CCNP – Add 2 more 3550 and two more 2900 routers
•
•
Why (emulation?)
•
•
GNS3 – Wireshark (http://www.gns3.net/download/)
Cables / cabling needs (Auto MDIX – medium dependent interface crossover)
•
2960 3560 both have Auto MDIX otherwise crossover cables it is
•
•
TSHOOT Exam Topology
http://monoprice.com
Next…Boot
BOOT
•
1. Bootstrap program ROMmon runs Power On Self Test (POST)
•
2. Bootstrap checks the Configuration Register in startup config file
• If nothing is there it will load from Flash
• No flash it will try to load from a TFTP server (assuming that you have one set up on
the network / program one in, ASA)
• If no TFTP server you would have to manually enter TFTP info from ROMMON
(SERVER = <tftp server>, SUBNET MASK=<subnet mask>, etc.)
•
3. IOS found now it is loaded into RAM (Self-decompressing the image: ####...)
•
4. Config file loaded from NVRAM (dir) into RAM if none found Setup dialogue
•
Next…Switching
SWITCHING BASICS
•
Models (Layers, TCP/IP versus DoD, real world)
•
Vlanning (Broadcast, Collision domains)
MODELS
•
TCP / IP (A Pizza Sure Tastes Nice During Presentations)
• Application – HTTP, everything
• Presentation – Human to computer (Layer 6)
• Session – Build and tear down of session (Layer 5)
• Transport – TCP/UDP (Layer 4) – a.ka. segment
• Network – IP Address (Layer 3) – a.k.a. packet
• Data Link – MAC (Layer 2) – a.k.a. frame
• Physical (Layer 1)
•
DoD
• Application (5 and up)
• Host-To-Host Layer (4)
• Internet Layer (3)
• Network Interface Layer (1 and 2)
•
Next…Vlanning
VLANING
•
Broadcast Domains – Stops at a Router (L3 device edge)
•
Collision Domains (hubs, repeaters) – Collision, hardware needs to listen for silence
• Switches eliminate this by moving the collision domain to the specific port
•
Next…MAC Addresses
MAC ADDRESSES
•
Mac address – unique identifier on a broadcast domain
• Entire thing 6 bytes (48 bits)
• OUI (first 3 bytes – or 24 bits)
• If someone says, “For ease of use I need to duplicate my mac, can I?” What do you
ask them?
•
Next…Address Resolution Protocol
ADDRESS RESOLUTION PROTOCOL
•
Arp requests – Hey who has an ip address of 192.168.0.1?
• Send a broadcast out ff:ff:ff:ff:ff:ff
• No MAC supplied in the arp request
•
Arp replies – Hey I have it!
•
GNS3 example
• Loop traffic? (https://supportforums.cisco.com/message/3005684#3005684) - self
looped port
• do wr, copy runnning-config startup-config, wr mem
•
Next…Cisco Discovery Protocol
CISCO DISCOVERY PROTOCOL
•
Cisco device sends out a multi-cast to 01:00:0c:cc:cc:cc with its mac address as source
•
No two way communication just multicasts
REFERENCES
•
http://www.9tut.com/cisco-router-boot-sequence-tutorial
•
http://www.petri.co.il/introduction-to-the-osi-model.htm