* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Inverter tests keep CCFLs shining
Spark-gap transmitter wikipedia , lookup
Wien bridge oscillator wikipedia , lookup
LCD television wikipedia , lookup
Oscilloscope history wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Josephson voltage standard wikipedia , lookup
Analog-to-digital converter wikipedia , lookup
Transistor–transistor logic wikipedia , lookup
Radio transmitter design wikipedia , lookup
Integrating ADC wikipedia , lookup
Valve audio amplifier technical specification wikipedia , lookup
Current source wikipedia , lookup
Power MOSFET wikipedia , lookup
Wilson current mirror wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Electrical ballast wikipedia , lookup
Surge protector wikipedia , lookup
Operational amplifier wikipedia , lookup
Schmitt trigger wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Voltage regulator wikipedia , lookup
Current mirror wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Opto-isolator wikipedia , lookup
Inverter tests keep CCFLs shining Tom Novitsky, VP Engineering and Bob Arnold, Engineering Manager, Endicott Research Group, Endicott, NY Endicott Research Group designs and manufactures DC-to-AC inverters used to power backlights that use CCFLs (cold cathode fluorescent lamps) as a light source. The company also manufactures drivers for backlights that use LEDs as light sources. CCFL backlights have been the light source for LCD backlights for years while LED backlights are just beginning use in applications that require added reliability and brightness, although at higher cost. Display applications require efficient inverters that can power a wide range of displays with minimal input power. These requirements are especially important with the ever increasing number of display products that use battery power, which further requires the inverter to operate seamlessly over a wide range of input voltage. Most of these displays utilize 5.7” to 15” diagonal LCDs, backlighted with one or two CCFLs. Using basic inverter design concepts, ERG engineers developed a low-profile series of DC-AC inverters. These inverter cover a wide input input voltage range (8 VDC to 18 VDC), open lamp detection, and they provide a wide dimming range using onboard PWM (pulse width modulation) brightness control, and lamp current regulation. Inverter workings The basic design of all ERG inverters involves a low-voltage oscillator that converts a DC input, typically 5 V to 12 V, into a low-voltage AC waveform that the a step-up transformer boosts to 1000 V rms to 2000 V rms, the voltage needed to start a CCFL. This voltage is called a start or strike voltage. Once the CCFL is lighted, the voltage and current required to maintain stable light output drops to 500 to 1000 V rms and 5 mA rms to 6 mA rms. The lowvoltage oscillator may be a discrete component Royer’s oscillator or it may use an IC to provide the required AC input to the transformer. Maintaining stable LCD brightness requires that the inverter’s output current remain stable over variations in input voltage and operating temperature. The inverter monitors output current and actively adjusts transformer input to maintain a 5% output current regulation. CCFL start or strike voltages vary widely with temperature, increasing dramatically at lower temperatures (Figure 1). At startup, the inverter monitors CCFL current while the strike voltage is increased to a maximum of 1800 V rms. Once the CCFL lights, the inverter reduces the voltage to the level required to maintain stable CCFL operation. If the CCFL is damaged or if the connection to the CCFL is open, the SFW open lamp detection function senses this and shuts down inverter operation pending fault correction. Figure 1. Starting voltages for CCFL’s increase as temperature decreases. Electrically, the CCFL load is a resistive load that varies not only among lamp designs, but with temperature and packaging. Lamp size and electro chemistry for displays of 5.7” to 15” size offer start voltages from 1000 V rms to 2000 V rms with sustaining voltages in the 500 V rms to 1000 V rms range. Lamp currents run from 5 mA to 6 mA rms. The start voltage increases with lamp age and with decreasing temperature. The sustaining voltage and lamp current also vary across the wide variety of CCFLs used in backlights. Additionally, variations in CCFL packaging provide variations in capacitive losses across different LCD assemblies that need to be considered. Dimming or brightness control is also a key design consideration to provide effective display function in night and daytime ambient light conditions. CCFL brightness is controlled pulse width modulation (PWM) dimming wherein the lamps are pulsed at a low frequency, typically 100 Hz to 200 Hz, and the duty cycle for each cycle varies from zero to 100%. A duty cycle of 50% then will provide display brightness approximately half that provided at a duty cycle of 100%. Figure 2 shows the lamp brightness versus current. Brightness stability at short duty cycles is the typical challenge for inverter design so the SFW Series design validation also included high dimming (low duty cycle) validation over variations in input voltage and temperature. Figure 2. A CCFL’s brightness is nearly linear with respect to current. Production test After ERG engineers verify an inverter design in the lab, the develop test specifications for manufacturing. The manufacturing team tests all products for proper function. The test data for each inverter, and there are thousands produced every week, is recorded and saved with appropriate manufacturing identification to provide a permanent record of the efficacy of each inverter produced. This data is used by ERG to monitor process stability and to provide a solid base of technical data on which to base product or process improvements. The test station (Figure 3) uses a 110 K, 10 W resistor to simulate the load of a CCFL to the inverter. A Fluke 45 DMM measures the input voltage while a handheld Fluke 87V measures the current. On the output side, a Fluke oscilloscope measures current and distortion through a Tektronix CT-2 current probe. From the input and output measurements, a PC running custom software calculates efficiency. If an invert has PWM brightness control, the system makes the measurements at full off, 50%, and full-on states. A 4-V power supply provides the control voltage to the inverter under test. A 0-V input forces some inverters to set their PWM controls to 100% duty cycle and 4-V for 0% while others use the opposite settings. Technicians use the handheld DMM to measure the frequency of the PWM signal at the inverter’s output. Test points on a test fixture or cable harnesses provide access to the inverter’s input and output pins, depending on the model. A 5-V or 12-V signal on the enable pin activates the inverter. Figure 3. An automated test system measures an inverter’s input and output from which ic calculates efficiency. Manufacturing test stations also include custom software to provide automatic input voltage regulation, inverter output measurement, and data recording for each inverter. There are numerous test stations throughout the factory that provide the manufacturing teams with a time efficient 100% test process. Design challenges Key challenges in designing a high voltage inverter include transformer design, ground-plane integrity, and high voltage clearance. Transformer challenges focused on meeting the 1800 V rms requirement, passing 2000 VDC Hipot (high potential) testing and achieving the correct leakage inductance, which determines the inverter oscillation frequency (55 KHz). The number of transformer secondary sections, how they are wound, and the physical dimensions all contribute to these challenges. PCB layout for high voltage inverters involves maintaining the clearances between high voltage traces and components required to insure against any high voltage arcing across the PCB surface. Another design and layout challenges is maintaining proper ground plane integrity is also key to providing regulated current control over the expected input voltage and output load variations.