* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Lab Writeup Diodes and AC
Negative resistance wikipedia , lookup
Regenerative circuit wikipedia , lookup
Transistor–transistor logic wikipedia , lookup
Oscilloscope types wikipedia , lookup
Integrating ADC wikipedia , lookup
Oscilloscope history wikipedia , lookup
Josephson voltage standard wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Nanofluidic circuitry wikipedia , lookup
Wilson current mirror wikipedia , lookup
Schmitt trigger wikipedia , lookup
Power MOSFET wikipedia , lookup
Operational amplifier wikipedia , lookup
Power electronics wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Voltage regulator wikipedia , lookup
Current source wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Surge protector wikipedia , lookup
Current mirror wikipedia , lookup
Network analysis (electrical circuits) wikipedia , lookup
AC and Diodes LBS 267L Objectives (1) To learn about the characteristics of diodes and how they are used for rectification. (2) To learn about filters which employ capacitors and resistors (3) To be able to: (a) construct correct rectifying circuits with and without filters from schematic drawings; (b) to distinguish between full and half-wave rectification; and (c) recognize circuits appropriate for each case. Theory Electric power is generated and transmitted from generating plants to businesses and homes in the form of an AC (originally "alternating current", but now any time varying signal in either current or voltage) signal such as that shown in Fig. l. The frequency of this AC signal is carefully controlled at 60 Hz (Cycles/sec), so that power from sources can be reliably combined. AC signals have the advantage that they can be conveniently "transformed" to larger or smaller values via transformers. AC currents and voltages can also be used for many purposes, such as electronic control and heating. Figure 1 For some purposes, however, it is essential to have a DC (time independent) signal. Uses include power supplies for heating and cooling control, bias voltages in electronic tubes and integrated circuits, etc. In this experiment we examine how an AC voltage can be turned into a DC voltage using a device called a DIODE. Unlike an electrical resistor, a diode is a NON-LINEAR device, that is, its output is not simply directly proportional to its input. A typical current-voltage characteristic for a Diode is shown in Fig. 2. For the present experiment, the most important feature of Fig. 2 is that the current that passes through the diode is large for positive applied voltage and very small for negative applied voltage. We can thus approximate the diode as a current gate, which passes current in one direction only. In this experiment we shall see how this property permits a diode to be used to convert AC current into DC current. In the circuit of Fig. 1 voltage is supplied by an AC (alternating current) generator. Its function is to produce the voltage shown on the right side of in Fig. l. Consider point a to be at ground (zero) potential (voltage), then the potential at point b varies with time as indicated. The voltage at point b changes AC and Diodes Write-up Page 1 periodically from positive to negative with respect to a. The current that flows through the circuit is, by Ohm's Law: I = V/R = (V0/R) sin t This current thus also changes periodically with time. When the polarity of V changes, the direction of the current also changes. The electrons carrying the current oscillate backward and forward about a mean position. Suppose now that we add to the circuit a diode as indicated. A diode usually consists of a junction of n- and p-type semiconducting materials. The current ID through the diode varies with the voltage VD applied across it as shown in Fig. 2. Current flows easily in one direction but not in the other. The direction of current flow is given by the direction of the arrow in the circuit symbol of the diode. It takes a certain finite voltage to turn on the current in the direction of the arrow in a diode, about 0.2 V for a germanium diode and about 0.5 V for a silicon diode. (If you want to learn more about diodes, you can read, e.g., chapter 4.9 of the book "Introductory Electronics for Scientists and Engineers" by R.E. Simpson. Allyn and Bacon, Inc., Boston 1977.) Alternatively, one may regard the resistance to current flow as being much greater in one direction than in the other or that the diode acts as a valve which lets current flow in one direction but not in the opposite one. In our circuit, appreciable current flows only in alternate half cycles of the applied potential. We can observe this by looking at the voltage across R with an oscilloscope. Since VR = IR, VR should only be non-zero on alternate cycles. The current and the voltage VR are called half wave rectified (Fig. 3). Full wave rectified current has the form also shown in Fig. 3. Figure 3 In both half and full wave rectified currents the current flow is always in the same direction. (Clockwise in the above circuit; by convention the direction of the current is taken parallel to the velocity of positive charge carriers and antiparallel to the velocity of negative charge carriers.) Filters For the operation of most electronic equipment, one needs a steady DC voltage rather than a full wave rectified voltage that varies with time. A DC voltage is obtained by applying the full wave rectified voltage to the input of a filter circuit. The output voltage obtained is shown in Fig. 4. AC and Diodes Write-up Page 2 Figure 4 It consists of an average DC voltage with a small "ripple" voltage superimposed upon it. In the experiment that follows, you will attempt to obtain an output for which the ratio of ripple voltage to DC voltage is a minimum, i.e. the purest DC voltage. You will examine both DC and ripple voltages. Both voltages will be measured quantitatively using an oscilloscope and a voltmeter. The amount of ripple is usually given as a percentage percent ripple, %R = Vrms(ripple)/VDC and the rms voltage is given in terms of the amplitude of a sine wave as Vrms = V0/1.414 Procedure Make sure that you understand how to connect the circuits correctly, and that you have them correctly connected before you turn them on!!! 1. Half-wave Rectifier Circuit: (a) Assemble the circuit of Fig. 5. The voltage V and ground G are applied to the red and black leads, respectively, of the oscilloscope (which in this case is analog input A of the PASCO interface) and the voltmeter. How does this circuit behave during the half cycle when current flows down (from 1 to 2) through the transformer? How does this circuit behave during the half cycle when current tends to flow up through the transformer? What would you thus predict for the voltage variation across the 5 k resistor? Verify by observing the wave form on the oscilloscope. The 5k resistor limits the current in the circuit to a value that is probably too small to give an appreciable reading on the ammeter. Note that a voltmeter is a DC meter. It therefore reads zero for AC signals and reads only the effective DC component of a rectified signal; the larger this DC reading, the more effective the rectification. Record the AC and DC voltages from the voltmeter and save the oscilloscope display for your report. (b) Insert the capacitive filter shown into the circuit of Fig. 5, first using the 2F capacitor and then the 20F capacitor (Fig. 6). POWER SHOULD BE OFF ON THE DIODE CIRCUITRY WHEN CHANGING THE CIRCUIT. THE SCOPE MAY BE LEFT ON. AC and Diodes Write-up Page 3 Observe and the resulting wave form and save it for your report. Estimate the DC component and the amount of ripple in percent from the trace on the oscilloscope. Then verify this by recording the AC and DC voltages on the voltmeter which is attached to the resistor also. (c) Insert into the original circuit of Part (a) a C-R-C filter shown in Fig. 7. Observe and save the resulting wave form for your report. Estimate the amount of ripple from the oscilloscope trace and with the voltmeter. 2) Full-wave Rectifier A circuit which uses the center tap of the transformer to make a full-wave rectifier is shown in Fig. 8. For simplicity in this and the next case we do not include a filter circuit, but obviously one could be added to smooth out the output voltage. Consider the half cycle for which point A has a negative potential with respect to ground and point B as a positive potential with respect to ground. Then the diode between 4 and 5 is conducting; the diode between points 9 and 10 is blocking (why?). Current will flow along the path A, 2, 32, 24, 23, 31, 30, 29, 5, 4, 1, A. Point 23 will be at a negative potential with respect to ground. (note: points 2, 32, 24 are at ground potential). For the other half cycle, point A has a positive potential with respect to ground and point B has a negative potential with respect to ground. Now the diode between points 4 and 5 is blocking (Why?). Current will flow along the path B, 2, 32, 24, 23, 31, 30, 29, 5, 10, 9, 3, B. Point 23 will, once again, be at negative potential with respect to ground. Record the wave form on the scope and record the DC voltage. 3) Bridge Rectifier A way to achieve full-wave rectification without the need for a transformer center tap is shown in Fig. 9. Explain in detail how this circuit gives full-wave rectification. Check with the scope that it does, once more save the scope display for your report, and estimate the percent ripple both from the display and the voltmeter. Your report should include scope displays from each of the circuits and a description of each. Be sure to include the DC voltage and percent ripple for the cases you have measured. Do not repeat the material in this write-up, but do try to describe what it is you have observed and what it means. AC and Diodes Write-up Page 4