Download Improved Reset / Power Down Alarm Circuit

Improved Reset / Power Down Alarm Circuit
Using inexpensive transistors and
79x05 or 78x05 regulators
Author: William G. Grimm
May 23, 2003
Consultant – Avorex Design
Introduction
Data sheets for PIC micro-controllers have typically included
recommended reset circuits.
While these perform well in most
applications, and are not needed at all in many others, they are
inadequate in some applications.
Such an applications would be
when the PIC is controlling or taking inputs from circuits with
voltages higher than its +5v supply voltage.
In these
applications the PIC can be up and running before its inputs from
the higher voltage circuits are valid, or, even worse, turning on
systems whose voltage levels have declined at turn off or brown
out.
In these applications designers may have considered using
micro-processor supervisory circuits that cost more than the PIC
itself. This application note describes how to avoid this.
The
that can
power on
gets its
following describes two circuits (in figures 2 and 3)
be used to provide a PIC with a reliable reset at both
and power down. These circuits may be used when the PIC
power through a voltage regulator.
The short coming of often published reset circuits is that
they measure only the +5 volt line supplying the PIC. Using such
circuits for reset means that when the PIC reset is drawn low at
power down the voltage on the PIC is already below +5 volts. The
voltage could be below the safe operating range of the part,
corrupting the program counter.
At best, little time is given
between the assertion of the reset and the power line going below
spec.
In operation this can shown itself as products going out of
calibration at power down, and processors coming up without a
valid reset on power up.
Circuit description
Figure 1 shows the circuit published with the data sheets of
PIC16c5x and PIC12c5xx parts and performs well in most
circumstances.
The point at which VDD must drop is given by
equation 1:
(equation 1)
VDD(R2/(R1 + R2)) = 0.7 volts
When VDD is above the threshold level, Q1 is conducting, taking
the MCLR line high. When VDD is below the threshold Q1 is turned
off and MCLR is brought low by R3. Resistor tolerances of R1 and
R2 will create uncertainties in the VDD reset trigger level.
Moreover, at power down the processor will not be drawn into reset
much before VDD goes too low for proper operation, making for a
time critical situation. At power up, the processor will not be
brought out of reset much before the voltage has become adequate,
again making for a time critical situation.
Figure 2 shows how the circuit in figure 1 can be modified to
eliminate the time criticality without adding parts.
U2 is the
regulator used to provide regulated 5 volt power to the PIC. U2
is not meant to be an additional voltage regulator, but the one
already in the design. In this example it is a negative voltage
regulator.
Q1 is turned on in normal operation, and turns off
when VIN falls below a level define by equation 2:
(equation 2)
VIN(R2/(R1 + R2)) = 0.7 volts
Solving equation 2 for R1 gives the means for calculating R1
based on the VIN you need to reach for safe microcontroller
operation:
(equation 3)
R1 = ((VIN/0.7 volts) – 1) * 1K
Here VIN is not near 5 volts, but at some voltage above the
regulator drop out voltage1 and below the normal operating
voltage. At power down this voltage will decline well before the
supply voltage.
The result is that the PIC MCLR line will be
brought to Vss level while its supply voltage (VDD-VSS) is still
+5, yielding more predictable results.
At power on, the MCLR line stays near Vss level until the
voltage regulator has passed its drop out range. The PIC will not
come out of reset until VDD-VSS has stability at 5 volts.
Sensing at the power supply side of the regulator allows the
sensing of a wider voltage range and is much more forgiving of
unit to unit variations in the values of R1 and R2.
Since many designs cannot use negative supplies, the circuit
in figure 3 has been included. U2 is again used to power the PIC,
but is now has the more common positive regulator. Q1 is now an
NPN transistor, but its operation is still defined by equation 2.
Q2 is used as a logic inverter stage and could be replaced by a
spare 74HC04 or 74HC14 gate if one is available.
Regulator drop out voltage is 7.3 volts for 78/79L05 and 7.5
volts for 78/7905.
National Semiconductor National Power IC's
Databook, 1995.
1
Both circuits in figures 2 and 3 have been tested with 78L05,
78L05, 7905 and 7805 linear regulators and found to be reliable.
Utilizing these circuits with switching regulators has not been
tested but should perform just as well.