Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
CHAPTER 25: CURRENT, RESISTANCE, AND EMF • So far we have studied electric interactions where the charges involved are at rest. In this chapter, we will now consider charges that are in motion. • We will do so first by studying circuits and the motion of charge through them – current Current • A current is the motion of charge from one region to another. More specifically, it is the rate at which charge crosses a given area. • For a conductor in electrostatic equilibrium, the electric field is zero everywhere inside the conductor, the charges are at rest, and there is no current • When we apply an electric field to a metal, the field exerts a force (F = eE) on the electrons and they begin to accelerate • Collisions between the electrons and the atoms of the metal slow them down, transforming the kinetic energy of the electron into thermal energy, making the metal warmer • The motion of the electrons will cease unless you continue pushing by maintaining an electric field • In a constant field, an electron’s average motion will be opposite the field – this motion is called the electron’s drift velocity vd, which corresponds to a net current • We learned that the electric field is zero inside a conductor in electrostatic equilibrium but a conductor with charges moving through it is NOT in electrostatic equilibrium • In different materials, the charges of moving particles can be positive or negative but in conductors, the moving charges are always electrons (negative) • Figure (a) shows positive charges drifting to the right because the electric force is in the same direction as the field • Figure (b) shows negative charges drifting to the left because the electric force is opposite to the direction of the field • In both cases there is a net flow of positive charge to the right OR you could also say there is a net flow of negative charge to the left – these are equivalent statements. We can either view current as negative charges moving in one direction OR view current as positive charges moving in the other direction – it makes no difference. • So, like most textbooks, we adopt the convention that current is the flow of positive charge – this is commonly referred to as “conventional current” (as opposed to “electron current”, which is in the opposite direction) • We will use the symbol I to denote conventional current • I is defined as the rate at which net charge crosses a given area (units: C/s, defined to be an ampere, A) • For a steady current (flow of charge is constant in time), I = ΔQ/Δt. For current that varies in time, the instantaneous current is I = dQ/dt. • Like charge, current has an algebraic sign, but neither are vectors – both charge and current are scalars • We can relate the current to the drift velocity of the moving charges • Consider the situation shown in the figure below, and let A be the crosssectional area of the cylinder, perpendicular to the field E • Let n denote the concentration of charge carriers – the number of moving charged particles per unit volume (units: 1/m3) and assume that all particles have the same drift velocity • In a small time interval Δt, each particle moves a distance Δx = vdΔt • The volume of the slice shown above (with thickness Δx) is AΔx or AvdΔt. If each particle has charge q, the amount of charge that flows out of the right end of this slice is given by ΔQ = nqAvdΔt • So, the current is I = ΔQ/Δt = n|q|Avd • The current density J is defined as the current per unit cross-sectional area and is given by J = I/A = n|q|vd (units: A/m2) • If the moving charges are positive, the drift velocity is in the same direction as the electric field; if the moving charges are negative, the drift velocity is in the opposite direction as the electric field • We can define the current density as a vector that takes into account the �⃗d direction of the drift velocity: 𝑱𝑱⃗ = 𝑛𝑛𝑛𝑛𝒗𝒗 **SEE EXAMPLE #1** Resistivity • The current density in a conductor depends on the electric field and the material properties of the conductor – for many conductors at a given temperature, 𝑱𝑱⃗ ∝ ��⃗ 𝑬𝑬, and the ratio E/J is constant • This relationship is called Ohm’s “law”. Like Hooke’s “law,” it is an idealized model that is only valid under certain circumstances • The ratio of the magnitudes of electric field to current density is called the resistivity of the material, ρ = E/J. For a given current density, the larger the resistivity of a metal is, the larger the field must be. • For ohmic materials, ρ is constant; in contrast, the resistivity of nonohmic materials depends on the field strength: ρ = ρ(E) • The units of resistivity are: (V/m)/(A/m2) = V*m/A. We will define another unit that we will soon discuss – the ohm: 1 Ω = 1 V/A. In terms of Ω, resistivity has units: Ω*m • An ideal conductor has zero resistivity and an ideal insulator has infinite resistivity • The reciprocal of resistivity is called conductivity: σ = 1/ρ (units: (Ω*m)-1) ��⃗ or • The microscopic version of Ohm’s law is generally written as 𝑱𝑱⃗ = 𝜎𝜎𝑬𝑬 ��⃗ 𝑬𝑬 = 𝜌𝜌𝑱𝑱⃗. This describes the behavior at a single point in a material in terms of the electric field and the current density at that point. We will discuss the macroscopic version of Ohm’s law, but first let’s discuss the dependence of resistivity on changes in the temperature of the material. Dependence on Temperature • In almost all cases, the resistivity of metallic conductors increases with increasing temperature • Physically, the ion cores of a conductor vibrate with larger amplitude as temperature increases, making it more probable that a collision with a moving electron occurs. These collisions cause the drift velocity to decrease, which leads to a reduction in the current. • Over a certain range of temperatures, the resistivity of a metal can be modeled as having a linear dependence on temperature T: 𝜌𝜌(𝑇𝑇) = 𝜌𝜌0 [1 + 𝛼𝛼(𝑇𝑇 − 𝑇𝑇0 )]. 𝜌𝜌0 is the resistivity at some reference temperature 𝑇𝑇0 and 𝛼𝛼 is called the temperature coefficient of resistivity. Resistance • ��⃗ 𝑬𝑬 and 𝑱𝑱⃗ are microscopic quantities and difficult to measure. The ��⃗ is the potential difference V and macroscopic quantity corresponding to 𝑬𝑬 the current I is the macroscopic quantity corresponding to 𝑱𝑱⃗. • Consider the case of a section of conducting wire with length L and crosssectional area A shown below. The potential difference between the ends is V and the field always points “downhill” (from higher potential to lower potential). The force on the positive charges is in the same direction as the field, so the (conventional) current I is also in the direction of decreasing potential. • If the current density and the electric field are uniform then the current is I = JA and the potential difference is V = EL. ρ = E/J = (V/L)/(I/A). Thus, 𝑉𝑉 = 𝜌𝜌𝜌𝜌 𝐴𝐴 𝐼𝐼 𝜌𝜌𝜌𝜌 • The quantity is defined as the resistance R of the conductor and is the 𝐴𝐴 macroscopic version of resistivity • The macroscopic version of Ohm’s law is then V = IR, where 𝑅𝑅 = 𝜌𝜌𝜌𝜌 𝐴𝐴 (units: Ω = V/A) and is usually taken to be constant (only true for ohmic materials) • Resistance increases with the length of the wire and decreases with its crosssectional area. As long as Ohm’s law is obeyed, there is a linear relationship between I and V, and the slope is 1/R (see figure below). • In addition to understanding how to use equations quantitatively, it is a good idea to also have a qualitative understanding of how a particular physical quantity changes when you vary some other quantity (see figure above) **SEE EXAMPLE #2** Electromotive Force and Circuits • If a conductor is not part of a closed loop (a complete circuit), then a steady current through it is not possible. • Imagine establishing an electric field ��⃗ 𝑬𝑬1 in a conductor such as the wire segment shown in the figure below. Current begins to flow in the direction of the applied field and positive charge builds up on the right end which causes a negative charge buildup on the left end (conservation of charge). • This separation of charge creates a field ��⃗ 𝑬𝑬2 in the direction opposite to the applied field. As the charge density on the ends increases so does the field strength of E2 until the net field is zero and the current stops flowing. • Let’s now consider a complete circuit and how to establish a steady current • Because the electric force is conservative, there can be no change in energy for a charge q making one complete circuit around a closed loop (ΔUloop = 0) • As discussed earlier, current flows thru a conductor in the direction of decreasing potential. So, if ΔVloop = 0, then there must be some part of the circuit where the potential also increases. Electromotive Force • The interaction that causes current to flow “uphill” – from lower to higher potential is called the electromotive “force” (abbreviated emf). This is not a force but rather a source of voltage that does work on a charge, increasing its potential (or potential energy). It has units of energy per unit charge (J/C = V) and the physical source of emf is often a battery. We will use the symbol ℰ to denote emf. • We will often treat a source of emf in a circuit as ideal, meaning that it maintains a constant potential difference across its terminals, independent of the amount of current through it • So inside of an emf source, some type of energy (chemical, mechanical, etc) is converted into electric potential energy, causing the positive charges to move “uphill” or “against the field”. Once the charge reaches the positive terminal and enters the wire, it flows through the wire towards the negative terminal of the source and its potential (energy) decreases. It then enters the emf source and moves “uphill” again and the process repeats. • For an ideal emf source connected to a resistor R, the potential increase due to the emf ℰ is exactly equal to the potential drop IR as the current flows thru the remainder of the circuit: ℰ = 𝐼𝐼𝐼𝐼 Internal resistance • Real sources of emf do not behave like this – the potential difference between the terminals is not equal to its emf. This is because there is always some amount of resistance in any material and we call this the internal resistance r of the source. • Assuming this resistance obeys Ohm’s law, the potential difference between the terminals of an emf source is ∆𝑉𝑉 = ℰ − 𝐼𝐼𝐼𝐼 • For a real emf source, the potential increase is now ℰ − 𝐼𝐼𝐼𝐼, which is exactly equal to the potential drop IR as the current flows thru the remainder of the circuit: ℰ − 𝐼𝐼𝐼𝐼 = 𝐼𝐼𝐼𝐼 so 𝐼𝐼 = ℰ 𝑅𝑅+𝑟𝑟 • We will use the concept of an ideal wire R = 0. So, the potential difference everywhere in the wire is also zero, even if there is current in it. • An ideal voltmeter has infinite resistance so that it can measure the potential difference between two points without changing it, which it would if some of the current flowed thru it • The resistance of an ideal ammeter is zero so that it can measure the current without changing it. If its resistance were not zero, then the current thru it would be smaller than it is in the circuit. **SEE EXAMPLE #3** Potential Changes in a Circuit • Because the electric force is conservative, the net change in potential energy for a charge making one complete trip around the circuit (a closed loop) must be zero. This means that the change in potential around the circuit is also zero. There is a potential gain across a source of emf and a potential drop associated with the resistance due to other circuit elements. Energy and Power in a Circuit ℰ − 𝐼𝐼𝐼𝐼 − 𝐼𝐼𝐼𝐼 = 0 • So we have talked about how electric potential increases or decreases as one goes around a circuit. This leads to changes in the potential energy associated with the electric potential of the circuit and the charge Q moving thru it. • A circuit involves various conversions of one form of energy to another as charges traverse different components of the circuit. Often we are interested in the rate at which this energy transfer takes place. • Consider some component in a circuit with a steady current I in it. Then in a time interval ∆𝑡𝑡, an amount of charge ∆𝑄𝑄 = 𝐼𝐼∆𝑡𝑡 has passed thru it • Denote the potential difference between the endpoints associated with the time interval ∆𝑡𝑡 as ∆𝑉𝑉. Then the change in potential energy is ∆𝑈𝑈 = ∆𝑄𝑄∆𝑉𝑉 = 𝐼𝐼∆𝑡𝑡∆𝑉𝑉. Dividing thru by ∆𝑡𝑡 gives an expression for the rate of energy transfer between the moving charges and a circuit element. This is usually referred to as power, P. • 𝑃𝑃 = ∆𝑈𝑈 ∆𝑡𝑡 = 𝐼𝐼∆𝑉𝑉, here ∆𝑉𝑉 is the potential difference across the entire circuit element (as usual, the SI unit for power is the watt: 1 W = 1 J/s) Resistor • Circuit elements called resistors have a fixed resistance R and the potential drop ∆𝑉𝑉 across a resistor depends on the current I flowing thru it, ∆𝑉𝑉 = 𝐼𝐼𝐼𝐼. Using Ohm’s law, the rate at which electric potential energy is converted to heat is given by 𝑃𝑃 = 𝐼𝐼∆𝑉𝑉 = 𝐼𝐼2 𝑅𝑅 = ∆𝑉𝑉 2 𝑅𝑅 . The current always enters a resistor at a higher potential and exits at a lower potential. • At an atomic level, the moving charges collide with the atoms in the resistor and some of their potential energy gets transferred to (or dissipated in) the resistor mostly in the form of heat or thermal energy Emf Source • A circuit element that supplies an emf to a circuit has a potential difference across its terminals. The current enters at the lower potential terminal (negative) and exits at the higher potential terminal (positive). • If the emf source also has an internal resistance then the potential difference between the terminals ∆𝑉𝑉 = ℰ − 𝐼𝐼𝐼𝐼, which is positive in the direction of the current • So instead of the moving charges delivering energy to a circuit element, as with a resistor; an emf source delivers energy to the free charges in the conductor. In the case of a battery, chemical energy is converted to electric potential energy. • The rate at which this energy transfer takes place is 𝑃𝑃 = 𝐼𝐼∆𝑉𝑉 = 𝐼𝐼ℰ − 𝐼𝐼2 𝑟𝑟 The term 𝐼𝐼ℰ represents the rate at which nonelectrical energy is converted to electrical energy. 𝐼𝐼 2 𝑟𝑟 represents the rate at which electrical energy is dissipated due to the internal resistance of the source. 𝐼𝐼ℰ − 𝐼𝐼 2 𝑟𝑟 is the net power output of the source. **SEE EXAMPLE #4** Microscopic Theory of Metallic Conduction • In the figure above, the ball represents a free electron colliding with the stationary ion cores of the conductor. The incline of the ramp indicates that the charge is moving in the direction of decreasing potential (in the direction of the electric field). • The average time between collisions is called the mean free time, τ • Earlier we defined the resistivity as ρ = E/J and the current density as J = nqvd • Metals make good conductors because they have a large number of free electrons that are readily accelerated by an applied electric field. The positive ion cores assemble in a crystal lattice and in the absence of an applied field, the free electrons move randomly thru this lattice at high speeds (~106 m/s) and, as a result, collide frequently with the ions and rebound in random directions. With no applied field, this random motion results in a zero average drift velocity (i.e., no net current). • Applying an electric field to the conductor gives the free electrons an acceleration in a direction opposite the field. They already have large kinetic energies, so an electron does not gain much energy from the field before colliding with another ion core. The result is that they acquire a small average velocity in a direction opposite the field – the drift velocity, vd. This constitutes a net current that is proportional to vd. • The drift velocity depends on 2 things: 1) the acceleration of the electrons and 2) the rate at which they undergo collisions • The acceleration is due to the electric force and opposite to the field, �𝒂𝒂⃗ = �⃗ 𝑭𝑭 𝑚𝑚 =− �⃗ 𝑒𝑒𝑬𝑬 𝑚𝑚 . This causes a change in the electron’s velocity during the time interval between collisions which, on average, is the mean free time. Thus, the electron’s average velocity due to the presence of the electric field (the drift velocity) is �𝒗𝒗⃗𝑑𝑑 = − �⃗ 𝑒𝑒𝑬𝑬 𝑚𝑚 𝜏𝜏 (~10-3 m/s). This is in addition to the random, high-speed motion that averages out to zero. �⃗𝑑𝑑 = • We defined the current density in terms of the drift velocity as 𝑱𝑱⃗ = 𝑛𝑛𝑛𝑛𝒗𝒗 �⃗𝑑𝑑 = −𝑛𝑛𝑛𝑛𝒗𝒗 𝑛𝑛𝑒𝑒 2 �𝑬𝑬⃗ 𝑚𝑚 𝜏𝜏. Comparing this with the microscopic version of Ohm’s 2 ��⃗� shows that the conductivity can be expressed as 𝜎𝜎 = 𝑛𝑛𝑒𝑒 𝜏𝜏 or law �𝑱𝑱⃗ = 𝜎𝜎𝑬𝑬 the 𝜌𝜌 = 𝑚𝑚 𝑛𝑛𝑒𝑒 2 𝜏𝜏 . 𝑚𝑚 • The time between collisions depends on several factors: the spacing of the ions in the crystal lattice, the presence of impurities, and how fast the electrons are moving • There are two kinds of motion of the electrons – the high-speed, random thermal motion and the slow, drift velocity acquired due to the presence of the applied field. vd is essentially negligible in determining the speed of the electrons and is not a factor in determining the time between collisions. • This means that the time between collisions and the conductivity are essentially independent of the applied electric field. If, also, the electron number density n does not depend on the applied electric field (which is ��⃗) is a linear relationship for usually the case) then Ohm’s law (𝑱𝑱⃗ = 𝜎𝜎𝑬𝑬 metallic conductors. • Almost all metals are ohmic (they obey Ohm’s law) provided the temperature of the metal is not too high and the applied electric field strength is not too large