Download PPP and Frame Relay

Document related concepts

Internet protocol suite wikipedia , lookup

Zero-configuration networking wikipedia , lookup

Recursive InterNetwork Architecture (RINA) wikipedia , lookup

Multiprotocol Label Switching wikipedia , lookup

CAN bus wikipedia , lookup

Airborne Networking wikipedia , lookup

UniPro protocol stack wikipedia , lookup

Cisco Systems wikipedia , lookup

Transcript
CCNA Guide to Cisco
Networking Fundamentals
Fourth Edition
Chapter 11
PPP and Frame Relay
Objectives
•
•
•
•
Describe PPP encapsulation
Configure PPP encapsulation and its options
Describe and enable PPP multilink
Understand Frame Relay standards and equipment
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
2
Objectives (continued)
• Describe the role of virtual circuits and performance
parameters in Frame Relay
• Understand the Frame Relay topologies
• Understand the difference between multipoint and
point-to-point configurations
• Configure and monitor Frame Relay
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
3
PPP
• PPP
– Internet standard protocol defined in RFCs 2153 and
1661
– Provide point-to-point, router-to-router, host-to-router,
and host-to-host connections
– Considered a peer technology based on its point-topoint physical configuration
– Commonly used over dial-up or leased lines to provide
connections into IP networks
• Serial Line Internet Protocol (SLIP) was the
predecessor to PPP
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
4
PPP (continued)
• PPP can be used over several different physical
interfaces, including the following:
– Asynchronous serial
– ISDN synchronous serial
– High-Speed Serial Interface (HSSI)
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
5
PPP in the Protocol Stack
• You can use PPP over both asynchronous and
synchronous connections
– At the Physical layer of the OSI reference model
• Link Control Protocol (LCP)
– Used at the Data Link layer to establish, configure,
and test the connection
• Network Control Protocols (NCPs)
– Allow the simultaneous use of multiple Network layer
protocols and are required for each protocol that uses
PPP
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
6
PPP in the Protocol Stack (continued)
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
7
Frame Format
• PPP is based on the High-Level Data Link
Control (HDLC) protocol
• The difference between PPP frames and HDLC
frames is that PPP frames contain protocol and
Link Control Protocol (LCP) fields
• LCP
– Described in RFCs 1548, 1570, 1661, 2153, and
2484
– Describes PPP organization and methodology,
including basic LCP extensions
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
8
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
9
Frame Format (continued)
• LCP field of the PPP packet can contain many
different pieces of information, including the
following:
–
–
–
–
–
–
–
Asynchronous character map
Maximum receive unit size
Compression
Authentication
Magic number
Link Quality Monitoring (LQM)
Multilink
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
10
Frame Format (continued)
• LCP link configuration process
– Modifies and enhances the default characteristics of
a PPP connection
• Includes the following actions:
–
–
–
–
–
Link establishment
Authentication (optional)
Link-quality determination (optional)
Network layer protocol configuration negotiation
Link termination
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
11
Establishing PPP Communications
• Involves the following actions:
– Link establishment
– Optional authentication
– Network layer protocol configuration negotiation
• The link establishment phase involves the
configuration and testing of the data link
• The authentication process can use two
authentication types with PPP connections: PAP
and CHAP
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
12
Establishing PPP Communications
(continued)
• PPP is an encapsulation type for serial interface
communications
– To configure a PPP connection, you must access the
interface configuration mode for the specific
interface you want to configure
• After LCP has finished negotiating the configuration
parameters
– Network layer protocols can be configured
individually by the appropriate NCP
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
13
Establishing PPP Communications
(continued)
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
14
Establishing PPP Communications
(continued)
• Configuring PPP Authentication
– Using authentication with PPP connections is
optional
– You must specifically configure PPP authentication
on each PPP host in order for the host to use it
– You can choose to enable CHAP, PAP, or both on
your PPP connection, in either order
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
15
Establishing PPP Communications
(continued)
• Once you set the authentication type
– You must still configure a username and password
for the authentication
• You must exit interface configuration mode and
enter global configuration mode
– Type username followed by the host name of the
remote router
– Then type password followed by the password for
that connection
• Confirming PPP Communications
– With the show interface command
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
16
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
17
Establishing PPP Communications
(continued)
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
18
Frame Relay Standards and
Equipment
• Frame Relay
– A packet switching and encapsulation technology
that functions at the Physical and Data Link layers of
the OSI reference model
– A communications technique for sending data over
high-speed digital connections
• ITU-T and ANSI define Frame Relay
– As a connection between the data terminal
equipment (DTE) and the data communications
equipment (DCE)
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
19
Frame Relay Standards and
Equipment (continued)
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
20
Frame Relay Standards and
Equipment (continued)
• The physical equipment that is used on a network
may vary from one organization to another
• Some routers have built-in cards that allow them to
make WAN connections
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
21
Frame Relay Standards and
Equipment (continued)
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
22
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
23
Frame Relay Standards and
Equipment (continued)
• Frame Relay access device (FRAD)
– Network device that connects to the Frame Relay
switch
– Also known as Frame Relay
assembler/disassembler
• Frame Relay network device (FRND)
– The Frame Relay switch
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
24
Virtual Circuits
• You can use Frame Relay with nearly any serial
interface
– Operates by multiplexing
• Frame Relay separates each data stream into
logical (software-maintained) connections
– Called virtual circuits
– Which carry the data transferred on the connection
• Two types of virtual circuits
– Switched virtual circuits (SVC)
– Permanent virtual circuits (PVC)
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
25
DLCI
• Frame relay connections identify virtual circuits by
Data Link Connection Identifier (DLCI) numbers
• A DLCI number associates an IP address with a
specific virtual circuit
• DLCI numbers have only local significance
• DLCI numbers are usually assigned by the Frame
Relay provider
– Most likely not the same on either side of the Frame
Relay switch
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
26
Frame Relay Map
• Frame Relay map
– A table in RAM that defines the remote interface to
which a specific DLCI number is mapped
• The definition will contain a DLCI number and an
interface identifier
– Which is typically a remote IP address
• The Frame Relay map can be built automatically or
statically depending on the Frame Relay topology
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
27
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
28
Frame Relay Map (continued)
• Subinterfaces
– Virtual interfaces associated with a physical interface
– Created by referencing the physical interface
followed by a period and a decimal number
• For the purposes of routing, however,
subinterfaces are treated as physical interfaces
• With subinterfaces, the cost of implementing
multiple Frame Relay virtual circuits is reduced
– Because only one port is required on the router
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
29
LMI
• LMI basically extended the functionality of Frame
Relay by:
– Making the DLCIs globally significant rather than
locally significant
– Creating a signaling mechanism between the router
and the Frame Relay switch, which could report on
the status of the link
– Supporting multicasting
• Providing DLCI numbers that are globally
significant makes automatic configuration of the
Frame Relay map possible
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
30
LMI (continued)
• LMI uses keepalive packets to verify the Frame
Relay link and to ensure the flow of data
• Each virtual circuit, represented by its DLCI
number, can have one of three connection states:
– Active
– Inactive
– Deleted
• The Frame Relay switch reports this status
information to the Frame Relay map on the local
router
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
31
Inverse ARP
• In multipoint configurations
– Routers use the protocol Inverse ARP to send a
query using the DLCI number to find a remote IP
address
• As other routers respond to the Inverse ARP
queries, the local router can build its Frame Relay
map automatically
• To maintain the Frame Relay map, routers
exchange Inverse ARP messages every 60
seconds by default
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
32
Encapsulation Types
• LMI has several different protocol encapsulation
types that it can use for management
communications
• Cisco routers support these types of LMI
encapsulation:
– cisco
– ansi
– q933a
• Cisco routers (using IOS Release 11.2 or later) can
“autosense” the LMI type used by the Frame Relay
switch
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
33
Encapsulation Types (continued)
• The basic LMI type has three information elements:
report type, keepalive, and PVC status
• Information concerning the status of the virtual
circuit:
–
–
–
–
–
–
–
New
Active
Receiver not ready
Minimum bandwidth
Global addressing
Multicasting
Provider-Initiated Status Update
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
34
Encapsulation Types (continued)
• Split horizon
– Routing technique that reduces the chance of
routing loops on a network
– Prevents routing update information received on one
physical interface from being rebroadcast to other
devices through that same physical interface
– People also refer to this rule as nonbroadcast
multiaccess (NBMA)
– Can cause problems for Frame Relay routing
updates
• The best solution is to configure separate point-topoint subinterfaces for each virtual connection
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
35
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
36
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
37
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
38
Performance Parameters
• Service contract specifies parameters by which the
connection is expected to function:
–
–
–
–
–
Access rate
Committed Information Rate (CIR)
Committed Burst Size (CBS)
Excess Burst Size (EBS)
Oversubscription
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
39
Congestion
• Frame Relay switches attempt to control
congestion on the network
• When the Frame Relay switch recognizes
congestion
– Sends a forward explicit congestion notification
(FECN) message to the destination router
• In addition, the switch sends a backward explicit
congestion notification (BECN) message to the
transmitting, or source, router
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
40
Frame Format
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
41
Frame Relay Topologies
• Frame Relay can use many different WAN
topologies:
–
–
–
–
Peer (point-to-point)
Star (hub and spoke)
Partial mesh
Full mesh physical
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
42
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
43
Frame Relay Configuration
• In this section, you will learn how to configure
Frame Relay over serial interfaces
– Using IP as the Network layer protocol
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
44
Basic Multipoint Configuration with
Two Routers
• LMI will notify the router about the available DLCI
numbers
– Inverse ARP will build the Frame Relay map
dynamically
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
45
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
46
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
47
Basic Multipoint Configuration with
Two Routers (continued)
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
48
Multipoint Configuration Using a
Subinterface
• The Frame Relay map will have to be built statically
on RouterA
– To configure a multipoint subinterface, you map it to
multiple remote routers using the same subnet
mask, but different DLCI numbers
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
49
Multipoint Configuration Using a
Subinterface (continued)
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
50
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
51
Point-to-Point Configuration Using
Subinterfaces
• Point-to-point Frame Relay configurations do not
support Inverse ARP
• You will have to configure each subnet separately
– Use the frame-relay interface-dlci command to
associate the DLCI numbers with a specific
subinterface
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
52
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
53
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
54
Frame Relay Static Mapping
• Sometimes you have to define the DLCI numbers
manually
– This is called making a static address to DLCI
Frame Relay map
• You statically configure your DLCI entries in the
following situations:
– The remote router does not support Inverse ARP
– You need to assign specific subinterfaces to specific
DLCI connections
– You want to reduce broadcast traffic
– You are configuring OSPF over Frame Relay
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
55
Non-Cisco Routers
• Non-Cisco routers use a different Frame Relay
encapsulation than Cisco routers
• If you are configuring Cisco routers to connect to
other Cisco routers
– They will automatically use the Cisco Frame Relay
encapsulation
• If you are connecting a Cisco router to a non-Cisco
router, you must specify ietf Frame Relay
encapsulation using the following command:
RouterA(config-if)#encapsulation framerelay ietf
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
56
Keepalive Configuration
• By default, keepalive packets are sent out every 10
seconds to the Frame Relay switch
• You can change the keepalive period by typing
keepalive followed by the time in seconds
RouterA(config-if)#keepalive 15
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
57
Monitoring Frame Relay
• You can check your Frame Relay configuration by
using show commands
– These commands allow you to verify that the
commands you previously entered produced the
desired effect on your router
• The most common show commands for monitoring
Frame Relay operation are:
show
show
show
show
interface
frame-relay pvc
frame-relay map
frame-relay lmi
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
58
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
59
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
60
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
61
Summary
• Many WAN connectivity options are available for
modern networks, including digital lines, Frame
Relay, and analog modems
• The Point-to-Point Protocol (PPP) is the most
widely used WAN protocol today
• PPP provides link establishment, quality
determination, Network layer protocol
encapsulation, and link termination services
• Frame relay is a flexible WAN technology that can
be used to connect two geographically separate
LANs
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
62
Summary (continued)
• Frame relay is both a service and type of
encapsulation
• Service parameters for Frame Relay include the
access rate, Committed Information Rate (CIR),
Committed Burst Size (CBS), and Excess Burst
Size (EBS)
• Frame relay connections employ virtual circuits that
can be either permanent or switched
• Virtual circuit connections across Frame Relay
connections are defined by Data Link Connection
Identifier (DLCI) numbers
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
63
Summary (continued)
• Most Frame Relay providers support LMI, which
allows Frame Relay maps to be dynamically
created via Inverse ARP
• Static mappings of DLCI numbers to remote IP
addresses can be configured when routers do not
support Inverse ARP
• Inverse ARP is not enabled on point-to-point links
because only one path is available
• Frame relay circuits can be established over serial
interfaces or subinterfaces on Cisco routers
CCNA Guide to Cisco Networking Fundamentals, Fourth Edition
64