* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download battery powered high voltage power supply for detectors Use the
Phone connector (audio) wikipedia , lookup
Spark-gap transmitter wikipedia , lookup
Solar micro-inverter wikipedia , lookup
Electric battery wikipedia , lookup
Electric power system wikipedia , lookup
Audio power wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Electrical ballast wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Power engineering wikipedia , lookup
Electrical substation wikipedia , lookup
Current source wikipedia , lookup
Power inverter wikipedia , lookup
Three-phase electric power wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Amtrak's 25 Hz traction power system wikipedia , lookup
History of electric power transmission wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Power MOSFET wikipedia , lookup
Distribution management system wikipedia , lookup
Schmitt trigger wikipedia , lookup
Surge protector wikipedia , lookup
Stray voltage wikipedia , lookup
Voltage regulator wikipedia , lookup
Alternating current wikipedia , lookup
Buck converter wikipedia , lookup
Opto-isolator wikipedia , lookup
Voltage optimisation wikipedia , lookup
HV5kV battery powered high voltage power supply for detectors Use the HV5kV to manage detectors which need up to 5 kV high voltage detectors. Or use just as a stand-alone versatile power supply for many nuclear electronics. The HV5kV is a battery powered high voltage power supply for semiconductor detectors. It can be used as an independent standalone device, but it is designed for use in conjunction with the MCA166, if the voltage supplied by the MCA itself is not high enough. It needs the same charging power supply as the MCA166 and it is designed such that HV5kV and MCA166 can be both connected to a single charger. The high voltage is adjusted by a 10turn-potentiometer. Correct operation is indicated by two LEDs. GBS Elektronik GmbH Bautzner Landstraße 22 01454 Großerkmannsdorf Germany Tel.: 0049 (0)351 21 70 07 - 0 Fax.: 0049 (0)351 21 70 07 - 21 E-Mail: [email protected] Website: www.gbs-elektronik.de HV5kV battery powered high voltage power supply for detectors Specification: • Output voltage 0 - 5 kV, adjustable. • Output current 10 μA max. • Accuracy of adjustment: better than 2% or 20 V, whatever is higher. • Ripple : < 1 mVpp at 5 kV, 1 μA. • Power on is indicated by a green LED. The red overload LED is on, when the output voltage is more than 2% lower than adjusted. • Voltage rise time < 500 V/s. For higher voltages, it may need some time until the overload LED extinguishes. • The output is short circuit proof. Overload is indicated by permanent operation of the overload LED. In this case, reduce voltage until overload LED extinguishes and try again. In the case that the problem persists, check HV5kV without load connected; check load, and check if battery voltage is low. • Output Connector: SHV • Power input: MCA166 charger connector, power output for connecting a MCA166 in chain. • Operating temperature -5 ...+50°C • Size 155*95*50 mm, same as MCA166 • Water and Dust protection IP 42 • Stand alone operating time 5-20h, depending on voltage • Contains a Li-Ion battery, 10 Wh Charge input Contact Signal 1 + charge voltage (8.4 V, 1 A max) 2 - charge voltage MCA Battery output 6.6 ... 8.4V, depending on battery charge state and current, 1A max., 6.6 Ohm output impedance. Wiring of output connector same as input connector. GBS Elektronik GmbH Bautzner Landstraße 22 01454 Großerkmannsdorf Germany Tel.: 0049 (0)351 21 70 07 - 0 Fax.: 0049 (0)351 21 70 07 - 21 E-Mail: [email protected] Website: www.gbs-elektronik.de