Download Light Emitting Diodes (LED`s)

LIGHT EMITTING DIODES
Presentation by PRATYUSH
MOHAPATRA
1
A light emitting diode (LED) is essentially a PN junction
opto-semiconductor that emits a monochromatic (single color) light
when operated in a forward biased direction.
LEDs convert electrical energy into light energy. They are
frequently used as "pilot" lights in electronic appliances to indicate
whether the circuit is closed or not.
2
About LEDs (1/2)
The most important part of a light emitting diode (LED) is the
semi-conductor chip located in the center of the bulb as shown at the
right. The chip has two regions separated by a junction. The p region
is dominated by positive electric charges, and the n region is
dominated by negative electric charges. The junction acts as a barrier
to the flow of electrons between the p and the n regions. Only when
sufficient voltage is applied to the semi-conductor chip, can the
current flow, and the electrons cross the junction into the p region.
3
How Does A LED Work? (1/2)
When sufficient voltage is applied to the
chip across the leads of the LED, electrons can
move easily in only one direction across the junction
between the p and n regions.
In the p region there are many more
positive than negative charges.
When a voltage is applied and the current
starts to flow, electrons in the n region have
sufficient energy to move across the junction into
the p region.
4
How Does A LED Work? (2/2)
Each time an electron recombines
with a positive charge, electric potential
energy is converted into electromagnetic
energy.
For each recombination of a negative
and a positive charge, a quantum of
electromagnetic energy is emitted in the
form of a photon of light with a frequency
characteristic of the semi-conductor material
(usually a combination of the chemical
elements gallium, arsenic and phosphorus)..
5
Testing LEDs
Never connect an LED directly to a
battery or power supply! It will be destroyed
almost instantly because too much current will
pass through and burn it out.
LEDs must have a resistor in series to
limit the current to a safe value, for quick
testing purposes a 1k resistor is suitable for
most LEDs if your supply voltage is 12V or less.
Remember to connect the LED the
correct way round!
6
How Much Energy Does an LED Emit?
The energy (E) of the light emitted by an LED is related to the
electric charge (q) of an electron and the voltage (V) required to light the
LED by the expression: E = qV Joules.
This expression simply says that the voltage is proportional to
the electric energy, and is a general statement which applies to any
circuit, as well as to LED's. The constant q is the electric charge of a
single electron, -1.6 x 10-19 Coulomb.
7
Finding the Energy from the Voltage
Suppose you measured the voltage across the leads of an LED,
and you wished to find the corresponding energy required to light the
LED. Let us say that you have a red LED, and the voltage measured
between the leads of is 1.71 Volts. So the Energy required to light the
LED is
E = qV or E = -1.6 x 10-19 (1.71) Joule,
since a Coulomb-Volt is a Joule. Multiplication of these numbers then gives
E = 2.74 x 10-19 Joule.
8
Applications
• Sensor Applications
• Mobile Applications
• Sign Applications
• Automative Uses
• LED Signals
• Illuminations
• Indicators
9
Sensor Applications






Medical Instrumentation
Bar Code Readers
Color & Money Sensors
Encoders
Optical Switches
Fiber Optic Communication
10
Mobile Applications





Mobile Phone
PDA's
Digital Cameras
Lap Tops
General Backlighting
11
Sign Applications




Full Color Video
Monochrome Message Boards
Traffic/VMS
Transportation - Passenger Information
12
Automative Applications



Interior Lighting - Instrument Panels & Switches, Courtesy Lighting
Exterior Lighting - CHMSL, Rear Stop/Turn/Tail
Truck/Bus Lighting - Retrofits, New Turn/Tail/Marker Lights
13
Signal Appications






Traffic
Rail
Aviation
Tower Lights
Runway Lights
Emergency/Police Vehicle Lighting
LEDs offer enormous benefits over traditional incandescent lamps
including:



Energy savings (up to 85% less power than incandescent)
Reduction in maintenance costs
Increased visibility in daylight and adverse weather conditions
14
Illumination (1/2)
Architectural Lighting
Signage (Channel Letters)
Machine Vision
Retail Displays
Emergency Lighting (Exit Signs)
Neon Replacement
Bulb Replacements
Flashlights
Outdoor Accent Lighting - Pathway, Marker Lights
15
Illumination (2/2)
LEDs not only consume far less electricity than traditional
forms of illumination, resulting in reduced energy costs, but require
less maintenance and repair. Studies have shown that the use of LEDs
in illumination applications can offer:
Greater visual appeal
Reduced energy costs
Increased attention capture
Savings in maintenance and lighting replacements
As white LED technology continues to improve, the use of
LEDs for general illumination applications will become more prevalent in
the industry.
16
Indication






Household appliances
VCR/ DVD/ Stereo and other audio and video devices
Toys/Games
Instrumentation
Security Equipment
Switches
17
Driving LEDs


Analog LED Drive Circuits
Digital LED Drive Circuits
18
Analog LED Drive Circuit
19
Digital LED Drive Circuits
20
Colours of LEDs (1/3)
LEDs are made from gallium-based
crystals that contain one or more additional
materials such as phosphorous to produce a
distinct
color.
Different
LED
chip
technologies emit light in specific regions
of the visible light spectrum and produce
different intensity levels.
LEDs are available in red, orange, amber, yellow, green, blue and
white. Blue and white LEDs are much more expensive than the other
colours. The colour of an LED is determined by the semiconductor
material, not by the colouring of the 'package' (the plastic body). LEDs of
all colours are available in uncoloured packages which may be diffused
(milky) or clear (often described as 'water clear'). The coloured packages
are also available as diffused (the standard type) or transparent.
21
Colours of LEDs (2/3)
Tri-colour LEDs
The most popular type of tri-colour LED has a red and a green
LED combined in one package with three leads. They are called tricolour because mixed red and green light appears to be yellow and this
is produced when both the red and green LEDs are on.
The diagram shows the construction of a tri - colour LED. Note
the different lengths of the three leads. The centre lead (k) is the
common cathode for both LEDs, the outer leads (a1 and a2) are the
anodes to the LEDs allowing each one to be lit separately, or both
together to give the third colour.
22
Colours of LEDs (3/3)
Bi-colour LEDs
A bi-colour LED has two LEDs wired in
'inverse
parallel'
(one
forwards,
one
backwards) combined in one package with two
leads. Only one of the LEDs can be lit at one
time and they are less useful than the tricolour LEDs described above.
23
Comparison Of Chip Technologies For
Wide-Angle, Non-Diffused LEDs
24
LED Performance (1/8)
LED performance is based on a few primary characteristics:







Color
White light
Intensity
Eye safety information
Visibility
Operating Life
Voltage/Design Current
25
LED Performance (2/8)
Colour
Peak wavelength is a function of the LED chip material.
Although process variations are ±10 NM, the 565 to 600 NM
wavelength spectral region is where the sensitivity level of the
human eye is highest. Therefore, it is easier to perceive color
variations in yellow and amber LEDs than other colors.
26
LED Performance (3/8)
White Light
When light from all parts of the visible spectrum overlap one
another, the additive mixture of colors appears white. However,
the eye does not require a mixture of all the colors of the
spectrum to perceive white light. Primary colors from the upper,
middle, and lower parts of the spectrum (red, green, and blue),
when combined, appear white.
27
LED Performance (4/8)
Intensity
LED light output varies with the type of chip, encapsulation,
efficiency of individual wafer lots and other variables. Several LED
manufacturers use terms such as "super-bright," and "ultra-bright“ to
describe LED intensity. Such terminology is entirely subjective, as
there is no industry standard for LED brightness.
28
LED Performance (5/8)
Eye Safety
The need to place eye safety labeling on LED products is
dependent upon the product design and the application. Only a few
LEDs produce sufficient intensity to require eye safety labeling.
However, for eye safety, do not stare into the light beam of any LED
at close range
29
LED Performance (6/8)
Visibility
Luminous intensity (Iv) does not represent the total light
output from an LED. Both the luminous intensity and the spatial
radiation pattern (viewing angle) must be taken into account. If two
LEDs have the same luminous intensity value, the lamp with the larger
viewing angle will have the higher total light output.
30
LED Performance (7/8)
Operating Life
Because LEDs are solid-state devices they are not subject to
catastrophic failure when operated within design parameters. DDP®
LEDs are designed to operate upwards of 100,000 hours at 25°C
ambient temperature. Operating life is characterized by the
degradation of LED intensity over time. When the LED degrades to half
of its original intensity after 100,000 hours it is at the end of its useful
life although the LED will continue to operate as output diminishes.
Unlike standard incandescent bulbs, DDP® LEDs resist shock and
vibration and can be cycled on and off without excessive degradation.
31
LED Performance (8/8)
Voltage/Design Current
LEDs are current-driven devices, not voltage driven. Although
drive current and light output are directly related, exceeding the
maximum current rating will produce excessive heat within the LED chip
due to excessive power dissipation. The result will be reduced light
output and reduced operating life.
LEDs that are designed to operate at a specific voltage contain a
built-in current-limiting resistor. Additional circuitry may include a
protection diode for AC operation or full-bridge rectifier for bipolar
operation. The operating current for a particular voltage is designed to
maintain LED reliability over its operating life.
32
Some Types of LEDs
Bargraph
7-segment
Starburst
Dot matrix
33