Download 120V/277V 0-10V Dimmer Module

120V/277V 0-10V Dimmer Module
Models: 74185 / 74197 / 74275 / 74296
For use with the following A21 120V/277V Lighting Control Panels:
A21 3-Space Panel, A21 6-Space Panel, A21 9-Space Panel
A21 120V/277V 0-10V Dimmer Module
Installation & Operation Guide
Description
The A21 0-10V Dimmer Modules offer reliable dimming of Advance® Mark 7®
fluorescent dimming ballasts.
All A21 Dimmer Modules have identical mounting dimensions, allowing them to
be easily swapped within any of the A21 Lighting Control Panels. (Use caution to
ensure that quad dimmer modules are not installed into module spaces wired for
dual dimmer modules.)
WARNING: Installing the module with power applied to the cabinet may
expose you to dangerous voltage and damage the device. Remove power
before installing. A qualified electrician should perform this installation.
Screw (4)
Blank Cover
(74181)
Screw (4)
Focus Button
& Status LEDs
Installation
Any combination of A21 dimming and relay modules may be installed in the Lighting Control Panel. Blank covers MUST be installed in any unused spaces. Pull the
jumper (shorting plugs) before installing.
To install modules:
Step 1. Unpack module and recycle or properly discard packaging materials. (Be
sure to keep this instruction sheet for future use.) Inspect dimming
module for signs of damage during transit.
Step 2. Disconnect main power to A21 Lighting Control Panel.
Step 3. Open dimmer module side of panel front cover.
Step 4. If present, remove blank cover from location where module is to be
installed (Figure 1). When possible, lower modules should be installed
first.
Step 5. Remove shorting plugs from the load terminal block. (The shorting plug
is the red tab protruding from the green load terminal block.) To remove,
grasp the shorting plug and gently pull. Note: The dimmer module will
not operate properly if the shorting plug is left in circuit.
Step 6. Gently insert module into lighting control panel, heatsink first. Secure
module using four screws (provided). Dimmer Module should be
installed with the heatsink facing away from you. Note: The connectors
of 277VAC A21 modules are keyed, preventing the insertion of modules
into panels of the incorrect voltage. Do not force modules into slots.
Step 7. Connect 0-10V control wires [violet (+) and grey (-)] to screw terminal
on 0-10V module (Figure 2 - depending on model). (Circuit #1 on
module will be top screw.) Tighten screw to a torque of 5 in-lbs. Connect
load (switched power) wiring to terminal block as indicated on panel.
Step 8. Close panel front cover.
Operation
A21 Dimmer Modules are equipped with a "Focus Button" on each circuit
(Figure 1). Tapping the focus button quickly will turn the circuit on to full, tapping
it quickly again will turn the circuit off. Pressing and holding the focus button will
ramp the dimmer up to full intensity. If the focus button is released before reaching
full intensity, the dimmer will stop at that relative output.
Red LED
Green LED
Off
Off
Normal
Off
On
Focus Mode (controlled at dimmer)
On
Off
Communication Error
Philips
Strand Lighting
10911 Petal Street
Dallas, TX 75238 USA
Condition
Dimmer
Module
NOTE: The A21 9-Module
Panel is used to illustrate
the installation. However,
module installation is identical for all Lighting Control Panel models.
Load Terminal Block
Terminal
Shorting
Plug
DETAIL
Figure 1: Installing Modules and Blank Covers
DUAL BALLAST
QUAD BALLAST
Control
Wiring:
Control
Wiring:
Dimmer A (+)
Dimmer A (-)
Dimmer B (+)
Dimmer B (-)
Dimmer A (+)
Dimmer A (-)
Dimmer B (+)
Dimmer B (-)
Dimmer C (+)
Dimmer C (-)
Dimmer D (+)
Dimmer D (-)
MODULE
FRONT
VIEW
MODULE
FRONT
VIEW
Figure 2: Ballast Wiring Connections
Electrical Specifications
Operating Voltage: 120VAC, 50/60Hz
Number of Circuits: 2
Min Rated Load (per circuit): 35W
Max Rated Load (per circuit): 74185: 2000VA
Operating Voltage: 120VAC, 50/60Hz
Number of Circuits: 4
Min Rated Load (per circuit): 35W
Max Rated Load (per circuit): 74197: 2000VA
Operating Voltage: 277VAC, 50/60Hz
Number of Circuits: 2
Min Rated Load (per circuit): 35W
Max Rated Load (per circuit): 74275: 4000W
Operating Voltage: 277VAC, 50/60Hz
Number of Circuits: 4
Min Rated Load (per circuit): 35W
Max Rated Load (per circuit): 74296: 4000W
Supported Loads: Advance® Mark 7® Ballasts
Cooling: Natural convection
Ambient Operating Temp: 0 to 40 degrees C
Relative Humidity: 5 to 95% (non-condensing)
Tel: 214-647-7880 | Fax: 214-647-8031
www.strandlighting.com
©2010 Philips Group
P/N: 85-5568B