* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download AP2BW8
Survey
Document related concepts
Operational amplifier wikipedia , lookup
Giant magnetoresistance wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Valve RF amplifier wikipedia , lookup
Nanofluidic circuitry wikipedia , lookup
Galvanometer wikipedia , lookup
Rectiverter wikipedia , lookup
Current mirror wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Lumped element model wikipedia , lookup
Current source wikipedia , lookup
Electrical ballast wikipedia , lookup
RLC circuit wikipedia , lookup
Transcript
BW 8 Ch. 23: CQ 17 – 22 P. 32 – 36 Q23.17. Reason: Applying Kirchhoff’s loop law around the outside edge of the circuit, That is, the potential difference DV12 between points 1 and 2 is potential supplied by the battery minus the potential lost in resistor R. When bulb B is in place, a current I exists through the resistor and the bulb. In that case, DV12 is less than But if bulb B is removed the current no longer exists in that branch (I = 0 A).Thus The answer is that the potential difference DV12 increases. Assess: Removing bulb B means that there is no resistor between points 1 and 2. “No resistor” is not the same as “no resistance.” “No resistor” means an insulator with R = ¥ W, not R = 0 W. Ohm’s laws applies to resistors, not to empty spaces. Although I = 0A when bulb B is removed, you cannot use IR to conclude that DV12 = 0 V because there is no longer a resistor between points 1 and 2 to which Ohm’s law could be applied. Q23.18. Reason: (a) The total current splits and some goes through the parallel branch containing the point a (the left branch) and some goes through the parallel branch containing the point b (the right branch). Notice that the resistance of each branch is the same (3R), as a result the current splits equally between the two branches. Let’s call the current in the two branches I. This current in the two branches causes a potential drop of 2IR in the resistor 2R in the left branch and a potential drop of IR in the resistor R in the right branch. As a result, the electric potential at point b is greater (it is more positive) than the electric potential at point a and DVab ¹ 0. (b) Since point b is at a higher potential than point a, if they are connected there will be an electric current from point b to point a. Assess: The solution of the question requires a good understanding of electric potential difference. Q23.19. Reason: (a) When the bulb is removed the resistance of that branch becomes ¥.The equivalent resistance of the parallel combination increases and is the resistance of the single -R branch. Since the resistance of the parallel combination has increased, the current decreases. (b) When the bulb is removed there is no potential difference across the resistor that is in series with the bulb because there is no current through the resistor (DV = IR). So the potential difference between 1 and 2 is now the potential difference of the parallel group. That is, removing the bulb increases the potential difference between 1 and 2. Assess: The second part is like Question 22.17, and we arrived at the same answer here. Q23.20. Reason: (a) A good voltmeter has very high resistance which causes the current in the incorrect circuit to be nearly zero. (b) Because there is no current there is no potential difference (voltage drop) across the resistor, so the voltmeter measures the emf of the battery, or 9 V. (c) Put the voltmeter in parallel with the resistor rather than in series with it. Assess: Voltmeters should be in parallel with the circuit element we want to know the potential difference across. Q23.21. Reason: (a) Because a good ammeter has very low resistance, the current would nearly all go through the ammeter, so the current in the 5.0 W resistor is nearly zero. (b) Put the ammeter in series with the resistor rather than in parallel with it. The current will be the same anywhere in the one-loop circuit, so it doesn’t matter exactly where the ammeter is placed in series. Assess: Ammeters should be placed in series in the circuit where we want to know the current. Q23.22. Reason: The equivalent capacitance of each grouping is determined as follows: Group 1: In this group we have three capacitors in series and the equivalent capacitance is 1/Ceq = 1/C1 + 1/C2 + 1/C3 or Ceq = C/3. Group 2: In this group we have three capacitors in parallel and the equivalent capacitance is Ceq = C1 + C2 + C3 = 3C. Group 3: In this group we have two capacitors in parallel and this combination is in series with the third capacitor. First determine the equivalent capacitance of the parallel combination and then consider this equivalent capacitance to be in series with the third capacitor. The equivalent parallel capacitance is CParallel = C + C = 2C. The equivalent capacitance for the group is determined by 1/Ceq = 1/CParallel +1/C = 1/(2C) +1/C = 3/(2C) or Ceq = 2C/3. Group 4: In this group we have two capacitors in series and this combination is in parallel with the third capacitor. First determine the equivalent capacitance of the series combination and then consider this equivalent capacitance to be in parallel with the third capacitor. The equivalent series capacitance is 1/Cseries = 1/C +1/C = 2/C or CSeries = C/2. The equivalent capacitance for the group is determined by Ceq = Cseries + C = C/2 + C = 3C/2. This allows us to rank the capacitance of the groups as follows: C2 = 3C > C4 = 3C/2 > C3 = 2C/3 > C1 = C/3. Assess: The solution of this question requires a good knowledge of how capacitors add in parallel and in series. P23.32. Prepare: Capacitors in parallel follow Equation 23.17. Solve: The equivalent capacitance is Ceq C1 C2 C3 6.0 F 10 F 16 F 32 F Assess: This value is the sum of all capacitances, so the result is reasonable. P23.33. Prepare: Capacitors in series follow Equation 23.19. Solve: The equivalent capacitance is -1 -1 æ 1 æ 1 1 1ö 1 1 ö Ceq = ç + + ÷ =ç + + = 3.04 ´ 10-6 F = 3.0 m F è 6.0 m F 10 m F 16 m F ÷ø è C1 C2 C3 ø Assess: This value is the smallest of all capacitances, so the result is reasonable. P23.34. Prepare: Two capacitors in parallel combine to give greater capacitance according to Equation 23.17. Solve: Since we want a capacitance of 50 F and we have a 30 F capacitor, we must connect the second capacitor in parallel with the 30 F capacitor. That is, C 30 F 50 F Þ C 50 F 30 F 20 F Assess: We must learn how the series and parallel circumstances combine. P23.35. Prepare: Two capacitors in series combine to give less capacitance according to Equation 23.19. Solve: Since we have a 75 F capacitor and we want a 50 F capacitance, we must connect the second capacitor in series with the 75 F capacitor. The capacitance of the second capacitor is calculated as follows: 1 1 1 Þ C 150 F + = 75 m F C 50 m F Assess: We must learn how to combine series and parallel capacitances. P23.36. Prepare: Please refer to figure P23.36. The pictorial representation shows how to find the equivalent capacitance of the three capacitors shown in the figure. Solve: Because C1 and C2 are in series, their equivalent capacitance Ceq 12 is 1 Ceq 12 = 1 1 1 1 1 Þ Ceq 12 12 F + = + = C1 C2 20 m F 30 m F 12 m F Then, Ceq 12 and C3 are in parallel. So, Ceq Ceq 12 C3 12 F 25 F 37 F Assess: We must understand well how to combine series and parallel capacitance.