* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Total Power Solutions
Pulse-width modulation wikipedia , lookup
Solar micro-inverter wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Telecommunications engineering wikipedia , lookup
Opto-isolator wikipedia , lookup
Three-phase electric power wikipedia , lookup
Power inverter wikipedia , lookup
Electric power system wikipedia , lookup
Electrification wikipedia , lookup
Audio power wikipedia , lookup
History of electric power transmission wikipedia , lookup
Buck converter wikipedia , lookup
Power electronics wikipedia , lookup
Distribution management system wikipedia , lookup
Power engineering wikipedia , lookup
Voltage optimisation wikipedia , lookup
Amtrak's 25 Hz traction power system wikipedia , lookup
Alternating current wikipedia , lookup
Power over Ethernet wikipedia , lookup
Power supply unit (computer) wikipedia , lookup
Mains electricity wikipedia , lookup
Power supply wikipedia , lookup
Power Total Power Solutions Generic Power Supplies To Load A Switch the battery breaker OFF. The power supply must be disconnected from line voltage during installation. A Necessary Cables To Batteries For any power supply that has a compatible output power connector, the XP-EDH-A can monitor the following parameters: • Input V • Output V • Battery string V • Individual battery V • Temperature • • • Use a surge protector in the cabinet when you are using a transformer to measure line voltage. Do not place the transponder on top of the power supply or the batteries. Make all battery harness connections and connect the interface cables to the power supply before connecting the cables to the transponder. Before field installation, the transponder's MAC address should be loaded into the CMTS, and DOCSIS configuration file options should be set; see the Network Installation Guide (Alpha P/N 745-838-C3). Detailed instructions for both network and field installation procedures are available in the XP-EDHA Technical Manual (Alpha P/N 745-838-B0) available at www.alpha.com. Alpha XM Series 2 Power Supply 120VAC TO 9VAC Power Output Cable with Transformer Provides Power to the Transponder 120Vac P/N 875-718-10 220Vac P/N 875-717-10 Or CBLPS-PWR-04-001 Alpha P/N 875-717-10 Alpha XP-EDH-A Transponder Field Installation Instructions CAUTION! NOTE: CBLPS-PWR-02-002 Alpha P/N 875-718-10 ® Switch the battery breaker OFF. Remove the Inverter Module from the power supply. See the power supply's technical manual for instructions. Make the jumps and switches, as shown below. USM2.5 220VAC TO 9VAC IEC C13 220V US NEMA 6-15P 3 FT CORD System RF Cable In After the jumps have been made and switches set to their correct positions, calibrate the scaled output voltage of the USM card. • On an uninstalled power supply, connect the output neutral to the power supply chassis. On installed power supplies this connection is made automatically in the SPI. USM2 JP2: 2-3 Jumped AlphaNet 0A C4 36 DOCSIS Transponder ON 1 2 3 JP1 (5V Position) • Connect the voltmeter's negative lead to pin 1 (bottom pin) of the Power Supply Interface Cable connector and its positive lead to pin 4 (4th from the bottom) of the connector. ON ON • For 60V power supplies, adjust the potentiometer (located next to the USM2/2.5 card’s white 15-pin connector and visible through a small hole) until the DC voltage at pin 4 (4th from the bottom) is 9.0 Vdc. For 90V power supplies, adjust it until the voltage at pin 4 is 13.5Vdc. To Battery Harness SW1 Settings: ON SW1 Settings: ON SW2 Setting: ON ON Necessary Cables RF Drop The downstream level (DS) into the transponder should be between -15 and +15 dBmV. JUMPED Verifying Installation and Network Connectivity • Once the firmware initializes, the LED sequence is as follows: 1. POWER LED on; all other LEDs off 2. DS, US flashing intermittently 3. ONLINE LED flashing fast and slow until registration is complete 4. ONLINE LED on solid indicating IP address has been assigned 5. DS flickering as data are sent from transponder to Network Management System • Once the AM MIBs have been set at the network end, the network connection can be remotely verified by entering the IP address into a web browser and confirming the display of correct power supply measurements. CBL-PS-INTFC-01-003 Alpha P/N 875-565-10 ON CBL-PS-INTFC-01-003 USM2 Cards Only <48V and >=20A ON ON 48V and <20A 220VAC TO 9VAC <48V and >=20A ON ON 48V and >=20A CBL-PS-PWR-03-002 Alpha P/N 875-562-10 US DS transformer module 0A C4 36 AlphaNet DOCSIS Transponder inverter module UNLATCH RIBBON CABLE RETAINER BEFORE FULLY REMOVING MODULE. ALARM ESC S Y S C O M 18 PIN Black wire BATTERY BREAKER N+1 Yellow wire OUTPUT N L SSR OUTPUT 2 LRI OUTPUT 1 BATTERY INPUT RED 16 PIN BLACK 14 PIN BLK Battery WHT Power Supply Important! Plug in the 13 pin connector so the black wire is in pin one (the bottom pin) and two open pins are left at the top for tamper switch connection. TMPR TEST Power TEMP PROBE RED USM2 Cards only AC Voltage Input 120V p/n 875-563-10 220V p/n 875-562-10 For more information visit www.alpha.com United States Canada Bellingham, Washington Tel: 360 647 2360 Fax: 360 671 4936 Burnaby, British Columbia Tel: 604 430 1476 Fax: 604 430 8908 To report errors in this document send email to: [email protected] Alpha Technologies reserves the right to make changes to the products and information contained in this document without notice. Copyright © 2008 Alpha Technologies. All Rights Reserved. Alpha® is a registered trademark of Alpha Technologies. member of The Alpha Group™ is a trademark of Alpha Technologies. 745-838-C2-003, Rev. C (12/2008) member of The GroupTM IEC C13 3 FT CORD OUTPUT See the XP-EDH-A technical manual (P/N 745-838-B0-001) or the network installation guide (P/N 745-838-C3-001). 220V US NEMA 6-15P 48V and >=20A ONLINE PWR 120VAC TO 9VAC CBL-PS-PWR-01-001 Alpha P/N 875-563-10 Or 48V and <20A System RF Cable in The remainder of the Installation is performed at the network end. <48V and <20A <48V and <20A ON BLACK To Battery Harness To Batteries Power Supply Interface Cable p/n 875-565-10 1 Total Power Solutions Total Power Solutions Alpha AM/AP Series Power Supply Alpha XM Series Power Supply Switch the battery breaker OFF. Switch the battery breaker OFF. NOTE: NOTE: • • Important! Plug in the 13 pin connector so the black wire is in pin one (the right-hand pin) and two open pins are on the left for tamper switch connection. • The power supply must be disconnected from line voltage during installation. • If not already installed, install an RPM card. Refer to RPM instructions for details. A chipset upgrade may be required; contact Alpha for more information. Set the jumpers and calibrate the USM card before making cable connections and applying load. Necessary Cables Power Power Supply 14 PIN Battery 18 PIN 16 PIN Yellow wire STANDBY STATUS RELAY 1 2 REMOTE INDICATOR LAMP 3 4 BATTERY CIRCUIT BREAKER AC OUTPUT 5 + 6 120VAC TO 9VAC CBL-PS-PWR-01-001 Alpha P/N 875-563-10 CBL-PS-PWR-03-002 Alpha P/N 875-562-10 Or 10 NC 9 COM 8 NO WARNING: 7 LAMP 6 5 4 OUTPUT 3 - BATTERY CONNECTOR B To Batteries ONLINE System RF Cable in US DS AlphaNet 0A C4 36 DOCSIS Transponder 2 Power Supply Interface Cable PWR Power Power Supply Battery 1 14 PIN 16 PIN 18 PIN - BLACK /AP AM S RED Side View 18 PIN Cut Here Red/Green wire CUT AND REMOVE A PIECE OF RED/GREEN WIRE IF PRESENT FOR XM SERIES ONLY Position 2-3 open open closed closed closed 5V 1-2 1-2 2-3 1-2 0 SW1 SW2 To Battery Harness Set to 0 (SWs 1,2,3 may not be present on some boards) SW3 Lectro ZTT and ZTT+ Power Supplies Maintain correct polarity when making this connection. If reversed, the transponder will be damaged and Vout will not be readable. Switch the battery breaker OFF. NOTE: SW4 P3 32 1 P1 P2 21 21 P4 P5 P6 R8 Potentiometer Adjuster Or 220VAC TO 9VAC 220V US NEMA 6-15P IEC C13 Outer band on DIN connector is black on older ZTT+ models and silver on newer models. 1 1 RJ Connector 1 5V P7 24V 15V PIN 1 Switch to ZTT Only for ZTT power supplies. Switch to +Silver or +Black for ZTT+ power supplies, depending on whether the outer band on the DIN connector is silver or black. Power Supply Interface P8 P9 1 2 3 DC AC CUR AC Volts P13 P14 1 1 2 2 3 3 Power Output Cable with transformer 120V p/n 875-718-10, 220V p/n 875-717-10 Necessary Cables = Jumped OU GR CBL-PS-INTFC-02-005 TAM After reinstalling the USM, calibrate the scaled output voltage of the USM card. To do this: • On an uninstalled power supply, connect the output neutral to the power supply chassis. On installed power supplies this connection is made automatically in the SPI. • Connect the voltmeter's negative lead to pin 1 (bottom pin) of the Power Supply Interface Cable connector and its positive lead to pin 4 (4th from the bottom) of the connector. • For 60V power supplies, adjust the potentiometer on the USM card until the voltage at pin 4 is 15Vdc. For 90V power supplies, adjust it until the voltage is 22.5Vdc. CBL-PS-INTFC-02-005 Alpha P/N 875-566-10 ND PER AlphaNet 0A C4 36 DOCSIS Transponder System RF Cable in 120VAC TO 9VAC CBLPS-PWR-02-002 Alpha P/N 875-718-10 To Battery Harness Or CBLPS-PWR-04-001 Alpha P/N 875-717-10 2 Power Supply Interface Cable 220VAC TO 9VAC IEC C13 220V US NEMA 6-15P 3 FT CORD 3 FT CORD To Load To Batteries ZT T 120VAC TO 9VAC CBL-PS-PWR-01-001 Alpha P/N 875-563-10 To Batteries p/n 875-564-10 ZT CBL-PS-INTFC-01-003 RED Power Supply Interface Cable SILVT+ ER ZT BLAT+ CK CBL-PS-INTFC-01-003 Alpha P/N 875-565-10 S The power supply must be disconnected from line voltage during installation. 1 2 3 Necessary Cables CBL-PS-BAT-04-004 CBL-PS-INTRFC-01-001 Jumper P1 P2 P3 P4 P5 P6 P7 P8 P9 P13 P14 SW4 I E CBL-PS-INTRFC-01-002 USM R Yellow wire AC Voltage Input 120V p/n 875-563-10 220V p/n 875-562-10 Remove the USM and set the jumpers as follow: CUT THE WIRE Battery IN UPPER LEFT POSITION AS SHOWN. ANY WIRE COLOR. Black wire E BLACK p/n 875-565-10 B CBL-PS-PWR-03-002 Alpha P/N 875-562-10 + BATT BLACK A ! IEC C13 OFF To Battery Harness Black wire 220V US NEMA 6-15P 3 FT CORD RED AC Voltage Input 120V p/n 875-563-10 220V p/n 875-562-10 a ligies Alphchno Te 220VAC TO 9VAC CBL-PS-INTFC-01-002 Alpha P/N 875-564--10 Fuse RED Black wire A BLACK PWR Important! Plug in the 13 pin connector so the black wire is in pin one (the top pin) and two open pins are left at the bottom for tamper switch connection. WARNING: CBL-PS-INTRFC-01-002 DS T 0A C4 36 AlphaNet DOCSIS Transponder US HO System RF Cable in T NEU ONLINE p/n 875-566-10 Ground Tamper 3