Download G2-56-0570

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Power factor wikipedia , lookup

Electric power system wikipedia , lookup

Solar micro-inverter wikipedia , lookup

Audio power wikipedia , lookup

Power inverter wikipedia , lookup

Electrical ballast wikipedia , lookup

Electrical substation wikipedia , lookup

Rectifier wikipedia , lookup

Ohm's law wikipedia , lookup

Thermal runaway wikipedia , lookup

Islanding wikipedia , lookup

Electrification wikipedia , lookup

Stray voltage wikipedia , lookup

Pulse-width modulation wikipedia , lookup

History of electric power transmission wikipedia , lookup

Thermal copper pillar bump wikipedia , lookup

Opto-isolator wikipedia , lookup

Power MOSFET wikipedia , lookup

Three-phase electric power wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Voltage regulator wikipedia , lookup

Surge protector wikipedia , lookup

Current source wikipedia , lookup

Lumped element model wikipedia , lookup

Power engineering wikipedia , lookup

Voltage optimisation wikipedia , lookup

Power electronics wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Mains electricity wikipedia , lookup

Buck converter wikipedia , lookup

Alternating current wikipedia , lookup

Transcript
Discover What’s Possible
1462 International Drive • Traverse City, Michigan 49686 • 877-774-7468 • www.tellurex.com
G2-56-0570 Thermoelectric Power Generation Module Specifications
The proprietary bonding technique used to assemble Tellurex power generation modules enables them to be used
in unequaled temperature ranges with unequaled thermal cycling capabilities. The G2 thermoelectric power generation module alloy is tuned for optimal operation in the temperature range of 200-250°C and can withstand continuous operating temperatures of 330°C.
Standard configuration is:
• Teflon insulated leads 300 to 330 mm (12 to 13 inches) stripped ends approx. 6mm (1/4 inch)
• 56 mm by 56xx mm (2.205 inches by 2.205 inches)
• Silicone perimeter seal dielectric protection
• Black graphite thermal interface material applied to hot and cold side
(hot side indicated by embossed graphite)
dimensions in millimeters
Performance
Optimum* Application**
Specifications
Thot 300°C
Tcold 30°C
Thot 250°C
Tcold 80°C
Open circuit
voltage
17.7
11.0
No load voltage measured at
TEG
Matched load
voltage
8.8
5.5
Voltage output when load resistance equals internal resistance
Matched load
current
2.0
1.25
Current output when load resistance equals internal resistance
Matched load
power
17.6
6.9
Power resultant at the load
(P=IxV)
Matched load
resistance
4.4
4.5
Internal resistance of TEG module at the operating temperature
Heat flow
through TEG
~327
~230
Approximate watts of heat flowing through the thermoelectric
generator
Heat flux
density
~10.4
~7.3
Approximate watts of heat per
square centimeter
Parameter
AC resistance
(@27°C)
2.4 ohms
(explanation of parameter)
315
56
4.3
Internal resistance measured at
room temperature
56
Operation Cautions:
• Thot not to exceed 400°C intermittent
• Tcold not to exceed 175°C
• Do not apply heat without adequate heat sink
*Optimum specification is an example of material performance
**Application specification is an example of a typical assembly
performance
Contact us...we’re ready to help:
Sales offices:
Web:
Email:
Mail:
+1 877-774-7468
www.tellurex.com
[email protected]
1462 International Drive
Traverse City, Michigan
Discover What’s Possible
1462 International Drive • Traverse City, Michigan 49686 • 877-774-7468 • www.tellurex.com
G2-56-0570 Thermoelectric Power Generation Module Specifications
Open Circuit Voltage
Matched Load Voltage
Matched load power output
Matched Load Resistance
Matched Load Current
Effect of load voltage on power output
Thot=300°C
Tcold=30°C
Performance Graphs and specifications are based on tests and measurements in controlled laboratory conditions.
Actual performance in applications may be influenced by conditions not present in laboratory testing.
Specifications and materials are subject to change without notice.