Download ANSWERS - AP Physics Multiple Choice Practice * Torque

ANSWERS - AP Physics Multiple Choice Practice – Dynamics
SECTION A – Linear Dynamics
Solution
Answer
1.
As T2 is more vertical, it is supporting more of the weight of the ball. The horizontal
components of T1 and T2 are equal.
C
2.
Normal force is perpendicular to the incline, friction acts up, parallel to the incline (opposite the
motion of the block), gravity acts straight down.
E
3.
F = ma; mgsin – f = ma
C
4.
The “diluted” force between objects is the applied force times the ratio of the mass behind the
rope to the total mass being pulled. This can be derived from a = F/m total and FT = mbehind the ropea
E
5.
F = ma; mg – bv = ma
B
6.
Ff = FN where FN is found from Fy = 0 = (FN – mg – Tsin)
A
7.
Fy = 0 = Fsin + FN – W
B
8.
The bottom of the rope supports the box, while the top of the rope must support the rope itself
and the box.
E
9.
The vertical components of the tension in the rope are two equal upward components of Tcos,
which support the weight. Fy = 0 = 2Tcos – W
D
10.
F = mg = kx (the negative sign merely indicates the direction of the spring force relative to the
displacement)
E
11.
Fexternal = mtotala;
mg is the only force acting from outside the system of masses so we have mg = (4m)a
B
12.
W = mg
D
13.
FN = mgcos, cos = adjacent/hypotenuse = 4/5
C
14.
Three vectors add to zero if they form the sides of a triangle, there is no requirement they be
equal or parallel, though it is possible.
A
15.
Any curvature of the line in a d-t graph indicates a non-zero acceleration
C
16.
Motion in a straight line does not mean the speed is constant. Simple harmonic motion is a
constantly changing velocity and can only occur with an acceleration. Motion in a circle
requires centripetal acceleration.
E
17.
F = ma; FT – mg = ma; Let FT = 50 N (the maximum possible tension) amd m = W/g = 3 kg
B
18.
The sum of the tensions in the chains (250 N + T left) must support the weight of the board and
the person (125 N + 500 N)
B
19.
From symmetry, each chain supports half of the weight of the board (62.5 N), The weight of the
person is then split between the chains with the left chain holding 375 N – 62.5 N = 312.5 N
and the right chain supporting 250 N – 62.5 N = 187.5 N or 3/5 of the tension in the left chain.
This means if the person sits a distance x from the left end, they sit a distance (5/3)x from the
right end. This gives x + (5/3)x = 4 m
B
20.
F = ma; 10 N – (30 N cos60º) = (10 kg)a
A
21.
Since the same force acts for the same time in each direction, the velocity in each direction is
the same. The vector should then point at a 45º angle in the first quadrant.
C
22.
Consider that no part of the system is in motion, this means at each end of the rope, a person
pulling with 100 N of force is reacted to with a tension in the rope of 100 N.
C
23.
As v is proportional to t2 and a is proportional to v/t, this means a should be proportional to t
E
24.
Fy = 0 = Tsin 30º – mg
D
25.
F = ma gives 20 N = (5 kg)a or an acceleration of 4 m/s 2. The 2 kg block is accelerating due to
the contact force from the 3 kg block Fcontact = ma = (2 kg)(4 m/s2) = 8 N. The 2 kg pushes back
on the 3 kg block with a force equal in magnitude and opposite in direction.
A
26.
The direction of the force is the same as the direction of the acceleration, which is proportional
to v = vf + (–vi)
B
27.
Fexternal = mtotala gives (0.90 kg × 10 m/s2) – (0.60 kg × 10 m/s2) = (1.5 kg)a
D
28.
Each spring supports half of the weight, or 6 N. F = kx
A
29.
gravity acts downward
D
30.
At constant speed F = 0; The forces acting parallel to the incline are F (up), F f (down) and
mgsin (down), which gives F – Ff – mgsin = 0, where Ff = FN = mgcos and cos = 4/5
B
31.
F = ma = Fcos – f
D
32.
f = FN where FN = mg – Fsin
E
33.
The string pulling all three masses (total 6m) must have the largest tension. String A is only
pulling the block of mass 3m and string B is pulling a total mass of 5m.
C
34.
At t = 2 s the force is 4 N. F = ma
B
35.
The upward component of the slanted cord is 300 N to balance the weight of the object. Since
the slanted cord is at an angle of 45º, it has an equal horizontal component. The horizontal
component of the slanted cord is equal to the tension in the horizontal cord.
D
36.
The normal force must point perpendicular to the surface and the weight must point down. In
order to accelerate up the ramp, there must be an applied force up the ramp. If the box is
accelerating up the ramp, friction acts down the ramp, opposite the motion.
E
37.
The normal force must point perpendicular to the surface and the weight must point down. If
the box is at rest on the ramp, friction acts up the ramp, opposing the tendency to slide down
C
38.
The normal force must point perpendicular to the surface and the weight must point down. If
the box is sliding down at constant speed, friction acts up the ramp, opposing the motion
C
39.
Fexternal = mtotala gives (Mg) – (mg) = (M + m)a
E
40.
To keep the box from slipping, friction up the wall must balance the weight of the block, or F f =
mg, where Ff = FN and FN = the applied force F. This gives F = mg
C
41.
Fexternal = mtotala gives (mg) – (10 N) = (m + 1 kg)(5 m/s2)
A
42.
Friction opposes the motion of the block and therefore points to the left. The normal force is
found from Fy = 0 = FN – mg – Fsin and the force of friction Ff = FN
E
43.
When an object exerts a force on a second object, the second object exerts an equal and
opposite force back on the first object.
C
44.
Since P is at an upward angle, the normal force is decreased as P supports some of the weight.
Since a component of P balances the frictional force, P itself must be larger than f.
A
45.
Newton’s 2nd law applied to an object sliding to rest gives F = –Ff = –FN = ma. On a
horizontal surface, FN = mg and we have –mg = ma, or a = –g. Use this acceleration with vf2
= vi2 + 2ad.
D
46.
F = ma = mv/t
C
47.
F = ma; Fcable – mg = ma = m(–2 m/s2)
C
48.
The force of friction = FN = 0.2 × 10 kg × 9.8 m/s2 = 19.6 N, which is greater than the applied
force, which means the object is accelerating to the left, or slowing down
A
49.
F = ma gives 36 N = (24 kg)a or an acceleration of 1.5 m/s 2. The 20 kg block is accelerating
due to the contact force from the 4 kg block Fcontact = ma = (20 kg)(1.5 m/s2) = 30 N.
D
50.
The upward component of the tension is T up = Tsin, where  is the angle to the horizontal.
This gives T = Tup/sin. Since the upward components are all equal to one half the weight, the
rope at the smallest angle (and the smallest value of sin) will have the greatest tension, and
most likely break
B
51.
Fexternal = mtotala gives (3.0 kg × 10 m/s2) – (1.5 kg × 10 m/s2) = (4.5 kg)a
C
52.
From the 1 kg block: F = ma giving a = 2 m/s2. For the system: F = (4 kg)(2 m/s2)
E
53.
For three forces in equilibrium, any one of the forces is equal and opposite to the resultant of the
other two forces.
D
54.
Elevator physics: FN represents the scale reading. F = ma; FN – mg = ma, or FN = m(g + a).
The velocity of the elevator is irrelevant.
B
55.
F = ma, if F is doubled, a is doubled. If m is halved, a will be doubled.
D
56.
Newton’s third law
C
57.
F = ma gives 24 N = (12 kg)a or an acceleration of 2 m/s2. The 3 kg block is accelerating due to
the tension in the rope FT = ma = (3 kg)(2 m/s2) = 6 N.
B
58.
Inertia is mass
E
59.
The normal force is mgcos. For a horizontal surface, FN = mg. At any angle FN < mg and Ff is
proportional to FN.
C
60.
F = ma, where m = W/g = 10 kg
B
61.
Newton’s 2nd law applied to an object sliding to rest gives F = –Ff = –FN = ma. On a
horizontal surface, FN = mg and we have –mg = ma, or a = –g. Using this acceleration with
vf2 = vi2 + 2ad gives d = vi2/2g. There is no dependence on mass.
B
62.
Newton’s 2nd law applied to an object sliding to rest gives F = –Ff = –FN = ma. On a
horizontal surface, FN = mg and we have –mg = ma, or a = –g. Using this acceleration with
vf2 = vi2 + 2ad gives d = vi2/2g. d is proportional to vi2
E
63.
F = ma and vf2 = 0 m/s = vi2 + 2ad
B
64.
The normal force on an incline is mgcos. The component of gravity acting down the incline is
mgsin. The coefficient of friction is minimized when static friction is at its maximum value,
or sFN. Keeping the block at rest requires mgsin = Ff = mgcos, or  = tan
C
65.
The maximum resultant possible from the sum of any two vectors is the sum of the magnitudes.
The minimum resultant possible is the difference between the magnitudes. Forces of 6 N and
10 N produce a maximum resultant of 16 N and a minimum of 4 N.
C
66.
An apple is approximately 100 g. It is important to have a sense of basic values of
measurement.
D
67.
F = ma. The component of gravity acting down the incline is mgsin, which gives a = gsin
C
68.
F = ma; mgsin – Ff = ma
B
69.
Slope = y/x = Weight/mass = acceleration due to gravity
D
70.
Newton’s second law applied to m1: T = m1a, or a = T/m1, substitute this into Newton’s second
law for the hanging mass: m2g – T = m2a
E
71.
Fy = 0 gives FN + (250 N sin30º) – mg = 0, or FN = 365 N. To move at constant speed, the
force of friction must balance the horizontal component of the applied force Fcos = 216.5 N =
FN
D
72.
String B is pulling both masses so FB = (6 kg)(12 m/s2)
A
73.
String A is only pulling the 4 kg mass so F A = (4kg)(12 m/s2)
B
74.
Fnet = ma
C
75.
Elevator physics: R represents the scale reading. F = ma; R – mg = ma, or R = m(g + a). This
ranks the value of R from largest to smallest as accelerating upward, constant speed,
accelerating downward
A
76.
F = ma for the whole system gives F – (3m)g = (3m)a and solving for a gives a = (F –
3mg)/3m. For the top block, Fm = ma = m[(F – 3mg)/3m]
A
77.
m × a = kg × m/s2
D
78.
The normal force comes from the perpendicular component of the applied force which is Fcos
= 50 N. The maximum value of static friction is then FN = 25 N. The upward component of
the applied force is Fsin = 87 N. Fy = Fup – mg = 87 N– 60 N > 25 N. Since the net force on
the block is great than static friction can hold, the block will begin moving up the wall. Since it
is in motion, kinetic friction is acting opposite the direction of the block’s motion
D
79.
Since P is at a downward angle, the normal force is increased. Since a component of P balances
the frictional force, P itself must be larger than f.
A
80.
Since the force is applied horizontally, the mass has no effect.
C
81.
Newton’s third law
E
82.
If they are not moving, the net force must be zero. While the book and crate are pushing each
other apart, there is friction from the table pointing inward against each object on the table to
keep them at rest.
C
83.
The only force in the direction of the crate’s acceleration is the force of friction from the sleigh
B
84.
Elevator physics: FN represents the scale reading. F = ma; FN – mg = ma, or FN = m(g + a).
When FN > mg, the elevator is accelerating upward (a is positive)
A
85.
Changing direction (choices A and C (the astronaut is still orbiting the earth!)) cannot occur
with a zero net force. Choices B and D represent accelerated motion.
E
86.
Given that the box accelerates toward Ted, Ted’s force must be greater than Mario’s force plus
the force of friction. Since Mario’s force is ½ of Ted’s force, the force of frction must be less
than half of Ted’s force.
A
87.
For a Newton’s third law pair, just switch the nouns.
C
88.
The component of gravity acting down the incline (+x) is mgsin and the component
perpendicularly intothe incline (–y) is mgcos. 36.9º indicates a 3-4-5 triangle.
A
89.
F = ma; F – mg = m(5g) or F = 6mg
A
90.
Fy = Fsin + FN – mg = 0, which gives FN = 170 N. The force of friction is equal to the
horizontal component of the force applied by the student which is Fcos = 86.6N. Ff = FN
C
91.
constant speed means Fnet = 0 N
A
92.
As the initial and final velocities and the displacement are given, as well as an indication that
the acceleration is constant, this is merely a kinematics problem. vf2 = vi2 + 2ad
E
93.
The maximum value of static friction in this case is sFN = 120 N. Since the person is pushing
with only 60 N of force, the box remains at rest.
C
94.
Between the lower block and the tabletop, there is a force of friction to the left of maximum
magnitude (2W) as both blocks are pushing down on the tabletop. There is also a force of
friction acting to the left on the upper surface of the lower block due to the upper block of
maximum magnitude W. The total maximum static frictional force holding the lower block in
place is therefore (2W) + W
E
95.
The normal force on the block can be found from Fy = 0 = FN – mgcos – F. The force of
friction necessary to hold the block in place is mgsin. Setting the force of friction equal to
mgsin gives FN = mgsin = (F + mgcos)
E
96.
In equilibrium, mg = kx and the equilibrium position x = mg/k. In an accelerating elevator, we
can just adjust gravity to its effective value geff = g + a, thus making the new equilibrium
position mgeff/k
C
97.
This is a tricky one. In order to move the car forward, the rear tires roll back against the
ground, the force of friction pushing forward on the rear tires. The front tires, however, are not
trying to roll on their own, rather they begin rolling due to the friction acting backward,
increasing their rate of rotation
A
98.
Gravity is still the only force acting vertically so we can find the total time in the air from
kinematics: vy = 0 at the top = v0sin – gt giving t (to the top) = v0sin/g and the total time is
twice the time to the top, or 2v0sin/g. In this time, the ball is also accelerating horizontally
(think of it as a “sideways” gravity) and in this time, should return to its starting location.
Using x = 0 = (v0cos)t + ½ at2, where a = F0/m and t is found above, we can solve for 
B
99.
The external forces acting on the system of masses are the weights of block 1 (pulling the
system to the left), the weight of block 3 (pulling the system to the right) and the force of
friction on block 2 (pulling the system to the left with a magnitude FN = m2g)
Fexternal = mtotala gives (m1g – m2g – m3g) = (m1 + m2 + m3)a
E
100. F = ma gives 30 N = (12 kg)a or an acceleration of 2.5 m/s 2. The 5 kg block is accelerating due
to the tension in the rope FT = ma = (5 kg)(2.5 m/s2) = 12.5 N.
C
101. Fexternal = mtotala gives (5.0 kg × 10 m/s2) – (3 kg × 10 m/s2) = (8 kg)a
E
102. As they are all at the same position after 8 seconds, they all have the same average velocity
D
103. Car A decelerates with the same magnitude that C accelerates. Car B is moving at constant
speed, which means FB = 0.
B
104. When falling with terminal velocity, the force of air resistance equals your weight, regardless of
the speed.
E
105.
For each case, Fexternal = mtotala gives Mg – mg = (M + m)a, or a 
M m
M m
A
g.
106. The two ends of the light string must have the same tension, eliminating choices A, C and D. If
choice E was correct, both masses would be accelerating downward and T A must be greater than
the weight of block A.
B
107. If F = ma, then m = F/a. For the second object m = 2F/5a = 2/5(F/a) = (2/5)m
A
108. Fexternal = mtotala gives (M + m)g – Mg = (2M + m)a
A
109. As the entire system moves as one, F = (3m)a, or a = F/(3m). The force of friction acting on
block 1 is the force moving block 1 and we have mg = m(F/(3m))
E
110. F = ma = mv/t
B
111. This is really no different than any other incline problem. The normal force on an incline with
no other forces acting into the incline is mgcos
E
112. Since the system is moving at constant velocity, m1 is pushing m2 and m3 with a force equal to
the force of friction acting on those two blocks, which is (FN2 + FN3)
A
113. Fexternal = mtotala gives (5 kg × 9.8 m/s2) – Ff = (10 kg)a, where Ff is the force of friction acting
on the 5 kg block on the table: mg = 0.2 × 5 kg × 9.8 m/s2 = 9.8 N
D
SECTION B – Circular Motion
1.
Newton’s third law
2.
2
F = mv /r;
v
Fr
; all other variables being constant, if r is quadrupled, v is doubled
m
B
D
3.
With acceleration south the car is at the top (north side) of the track as the acceleration points
toward the center of the circular track. Moving east indicates the car is travelling clockwise.
The magnitude of the acceleration is found from a = v2/r
A
4.
The frictional force acts as the centripetal force (toward the center)
D
5.
Acceleration occurs when an object is changing speed and/or direction
D
6.
Velocity is tangential, acceleration points toward the center of the circular path
B
7.
To move in a circle, a force directed toward the center of the circle is required. While the
package slides to the right in the car, it is actually moving in its original straight line path while
the car turns from under it.
E
8.
a = v2/r and v = 2r/T giving a = 42r/T2
B
9.
Once projected, the ball is no longer subject to a force and will travel in a straight line with a
component of its velocity tangent to the circular path and a component outward due to the
spring
E
10.
There is a normal force directed upward and a centripetal force directed inward.
D
11.
a = v2/r where v = 2rf and f = 2.0 rev/sec
D
12.
At Q the ball is in circular motion and the acceleration should point to the center of the circle.
At R, the ball comes to rest and is subject to gravity as in free-fall.
C
13.
The net force and the acceleration must point in the same direction. Velocity points tangent to
the objects path.
D
14.
The centripetal force is provided by the spring where FC = Fs = kx
B
15.
In the straight sections there is no acceleration, in the circular sections, there is a centripetal
acceleration
B
16.
Once the stone is stuck, it is moving in circular motion. At the bottom of the circle, the
acceleration points toward the center of the circle at that point.
A
17.
Feeling weightless is when the normal force goes to zero, which in only possible going over the
top of the hill where mg (inward) – FN (outward) = mv2/R. Setting FN to zero gives a maximum
A
speed of
gR
18.
Centripetal force points toward the center of the circle
B
19.
While speed may be constant, the changing direction means velocity cannot be constant as
velocity is a vector
B
20.
F = mv2/r. Fnew = (2m)(2v)2/(2r) = 4(mv2/r) = 4F
D
21.
Assuming the track is circular at the bottom, the acceleration points toward the center of the
circular path
A
22.
Average speed = (total distance)/(total time). Lowest average speed is the car that covered the
C
least distance
23.
As all the cars are changing direction, there must be a net force to change the direction of their
velocity vectors
D
24.
F = mv2/r; v2 = rF/m, if r decreases, v will decrease with the same applied force. Also, v = 2rf
so 42r2f = rF/m, or f = F/(42rm) and as r decreases, f increases.
D
25.
f = 4 rev/sec. a = v2/r and v = 2rf
D
26.
F = mv2/r
D
27.
There is a force acting downward (gravity) and a centripetal force acting toward the center of
the circle (up and to the right). Adding these vectors cannot produce resultants in the directions
of B, C, D or E.
A
28.
F = ma; mg + FT = mv2/r giving FT = mv2/r – mg
B
29.
At the top of the circle, F = FT + mg = mv2/R, giving FT = mv2/R – mg. At the bottom of the
circle, F = FT – mg = mv2/R, giving FT = mv2/R + mg The difference is (mv2/R + mg) –
(mv2/R – mg)
B
30.
At the bottom of the swing, F = FT – mg = mac; since the tension is 1.5 times the weight of the
object we can write 1.5mg – mg = mac, giving 0.5mg = mac
B
31.
C
Ff
FN =
mv2/r
mg
Ff = mg to balance
FN = mv2/r = mg, where v = 2rf which gives  = g/(42rf2)
Be careful! f is given in rev/min (45 rev/min = 0.75 rev/sec) and 8.0 m is the ride’s diameter