2. NF effects
... sees the resistance of the voltage divider. To study the effect on negative feedback on the input resistance of the amplifier it is necessary to avoid the influence of the resistance of the divider on the small signal resistance seen by the signal source. The solution is to use the bootstrap method ...
... sees the resistance of the voltage divider. To study the effect on negative feedback on the input resistance of the amplifier it is necessary to avoid the influence of the resistance of the divider on the small signal resistance seen by the signal source. The solution is to use the bootstrap method ...
RF Solutions - Beholder Europe
... • Standard FM radio coverage 87.5 to 108 MHz • 5V supply with integrated DC-DC converter for tuning voltage supply • Excellent Phase Noise for best performance (typically -105 dBc @ 10 kHz) • Full frequency coverage from Ch E2 to E69 • PLL controlled tuning with crystal accuracy • Programmable PLL s ...
... • Standard FM radio coverage 87.5 to 108 MHz • 5V supply with integrated DC-DC converter for tuning voltage supply • Excellent Phase Noise for best performance (typically -105 dBc @ 10 kHz) • Full frequency coverage from Ch E2 to E69 • PLL controlled tuning with crystal accuracy • Programmable PLL s ...
Modeling and Control of a Magnetic Levitation System
... project examined the different approaches in obtaining a model for the maglev system. Another practice in control systems is investigating performance of different controllers such as analog vs. digital. The analog controller from the manufacturer was converted to digital equivalent using bilinear t ...
... project examined the different approaches in obtaining a model for the maglev system. Another practice in control systems is investigating performance of different controllers such as analog vs. digital. The analog controller from the manufacturer was converted to digital equivalent using bilinear t ...
lab8 - ECE UC Davis
... when connected in feedback, is not unity-gain stable. Therefore, it will oscillate if it is connected in a feedback configuration with too much feedback. Also, in order to make the open-loop gain characteristic easy to measure, the gain of the circuit is intentionally designed to be less than 1000. ...
... when connected in feedback, is not unity-gain stable. Therefore, it will oscillate if it is connected in a feedback configuration with too much feedback. Also, in order to make the open-loop gain characteristic easy to measure, the gain of the circuit is intentionally designed to be less than 1000. ...
Volt-Ohm-Milliampere Meter (VOM)
... microammeter, e.g. 50 µA, 2000 Ω, in order to limit the current passing through it. The voltage obtained can be computed from the passing current and the resistance value. Procedures for AC voltage measurement is similar to DC voltage measurment, however, a rectifier is required in order to convert ...
... microammeter, e.g. 50 µA, 2000 Ω, in order to limit the current passing through it. The voltage obtained can be computed from the passing current and the resistance value. Procedures for AC voltage measurement is similar to DC voltage measurment, however, a rectifier is required in order to convert ...
Physics 2511 Laboratory Manual
... Safety in the laboratory is very important. The experiments performed in the laboratory are designed to be as safe as possible, but caution is always advised concerning the use of the equipment. When you arrive at the start of each class meeting, it is very important that you do not touch or turn on ...
... Safety in the laboratory is very important. The experiments performed in the laboratory are designed to be as safe as possible, but caution is always advised concerning the use of the equipment. When you arrive at the start of each class meeting, it is very important that you do not touch or turn on ...
lab4_beam_vibration
... The third VI “Freqresponse VI” is used to determine the frequency response of the beam. On the front panel of the VI, parameters are set for the input and output signals. The values found by the Frequency Response VI for n, and need to be entered along with the length and half the thickness (c) o ...
... The third VI “Freqresponse VI” is used to determine the frequency response of the beam. On the front panel of the VI, parameters are set for the input and output signals. The values found by the Frequency Response VI for n, and need to be entered along with the length and half the thickness (c) o ...
Analysis and Simulation of an Analog Guitar Compressor
... effect of the DynaComp is used to smooth out differences in volume between notes. Thereby it is a kind of volume controller that varies its internal gain to sustain the guitar sound. In recent years a new trend has won recognition in music technology - the digital modeling and simulation of analog a ...
... effect of the DynaComp is used to smooth out differences in volume between notes. Thereby it is a kind of volume controller that varies its internal gain to sustain the guitar sound. In recent years a new trend has won recognition in music technology - the digital modeling and simulation of analog a ...
Book 5 - radartutorial.eu
... generator for Radar applications. Magnetrons function as self-excited microwave oscillators. Crossed electron and magnetic fields are used in the magnetron to produce the high-power output Figure 9: Magnetron МИ 29Г of the old required in radar equipment. These multicavity devices russian Radar “Bar ...
... generator for Radar applications. Magnetrons function as self-excited microwave oscillators. Crossed electron and magnetic fields are used in the magnetron to produce the high-power output Figure 9: Magnetron МИ 29Г of the old required in radar equipment. These multicavity devices russian Radar “Bar ...
Evaluates: MAX105/MAX107 MAX105 Evaluation Kit General Description Features
... Out-of-Range (DOR) Signal The out-of-range signal (DOR+, DOR-) flags high when either the I or Q input is below -FS or above +FS. The out-of-range signal has the same latency as the ADC output data or is demultiplexed the same way. For an 800MHz system DOR+ and DOR- are clocked at 400MHz. ...
... Out-of-Range (DOR) Signal The out-of-range signal (DOR+, DOR-) flags high when either the I or Q input is below -FS or above +FS. The out-of-range signal has the same latency as the ADC output data or is demultiplexed the same way. For an 800MHz system DOR+ and DOR- are clocked at 400MHz. ...
Paperless Recorder - Fuji Electric Corp. of America
... (Pt100, JPt100, Ni100, Pt50, Cu50) DC voltage: (0 to 50mV, 0 to 500mV, 0 to 5V or 1 to 5V) DC current: (connecting optional shunt resistor to input terminal) Selected from the key panel (the same type should be set for every 2 channels) Equipped with thermocouple and resistance bulb inputs as standa ...
... (Pt100, JPt100, Ni100, Pt50, Cu50) DC voltage: (0 to 50mV, 0 to 500mV, 0 to 5V or 1 to 5V) DC current: (connecting optional shunt resistor to input terminal) Selected from the key panel (the same type should be set for every 2 channels) Equipped with thermocouple and resistance bulb inputs as standa ...
Oscilloscope types
This is a subdivision of the Oscilloscope article, discussing the various types and models of oscilloscopes in greater detail.