AD628 High Common-Mode Voltage Programmable Gain
... ±5 V, ±10 V, and 4–20 mA input signals to a single-ended output within the input range of single-supply ADCs. The AD628 has an input common-mode and differential mode operating range of ±120 V. The high common-mode input impedance makes the device well suited for high voltage measurements across a s ...
... ±5 V, ±10 V, and 4–20 mA input signals to a single-ended output within the input range of single-supply ADCs. The AD628 has an input common-mode and differential mode operating range of ±120 V. The high common-mode input impedance makes the device well suited for high voltage measurements across a s ...
Chapter 3
... • In cutoff IC = 0A and all of VCC is dropped across the transistor • In Saturation only an insignificant amount of VCC is dropped across the transistor. ...
... • In cutoff IC = 0A and all of VCC is dropped across the transistor • In Saturation only an insignificant amount of VCC is dropped across the transistor. ...
AD8517
... voltage offset of 1.3 mV from a 1.8 V supply. The low supply current makes these parts ideal for battery-powered applications. The 8 V/µs slew rate makes the AD8517/AD8527 a good match for driving ASIC inputs, such as voice codecs. The AD8517/AD8527 is specified over the extended industrial (–40°C t ...
... voltage offset of 1.3 mV from a 1.8 V supply. The low supply current makes these parts ideal for battery-powered applications. The 8 V/µs slew rate makes the AD8517/AD8527 a good match for driving ASIC inputs, such as voice codecs. The AD8517/AD8527 is specified over the extended industrial (–40°C t ...
INA111 High Speed FET-Input INSTRUMENTATION AMPLIFIER
... power supply voltages. If the input current is limited to less than 1mA, clamp diodes are not required; internal junctions will clamp the input voltage to safe levels. If the input source can supply more than 1mA, use external clamp diodes as shown in Figure 5. The source current can be limited with ...
... power supply voltages. If the input current is limited to less than 1mA, clamp diodes are not required; internal junctions will clamp the input voltage to safe levels. If the input source can supply more than 1mA, use external clamp diodes as shown in Figure 5. The source current can be limited with ...
General Question Pool --- July 1, 2007
... A Product detector circuit is used to process signals from the IF amplifier and BFO and send the result to the AF amplifier in a single-sideband phone superheterodyne receiver. ...
... A Product detector circuit is used to process signals from the IF amplifier and BFO and send the result to the AF amplifier in a single-sideband phone superheterodyne receiver. ...
An Analog Current Controller Design for Laser Diodes
... royally screw up an atomic physics experiment). We also have a switch in front of this circuit in the housing which may be used to short out the diode circuit after switching it off before removing power connectors. the purpose of removing the small absolute error of the sense resistor if such accur ...
... royally screw up an atomic physics experiment). We also have a switch in front of this circuit in the housing which may be used to short out the diode circuit after switching it off before removing power connectors. the purpose of removing the small absolute error of the sense resistor if such accur ...
Chapter 14
... in common-base configuration, the collector current is proportional to the collector-base voltage in common-emitter configuration, the base current is less than the base current in commonbase configuration the collector current flow is independent of the emitter current flow for a given value of col ...
... in common-base configuration, the collector current is proportional to the collector-base voltage in common-emitter configuration, the base current is less than the base current in commonbase configuration the collector current flow is independent of the emitter current flow for a given value of col ...
Dual Bipolar/JFET, Audio Operational Amplifier OP275 *
... Since the OP275’s input stage combines bipolar transistors for low noise and p-channel JFETs for high speed performance, the output voltage of the OP275 may exhibit phase reversal if either of its inputs exceeds its negative common-mode input voltage. This might occur in very severe industrial appli ...
... Since the OP275’s input stage combines bipolar transistors for low noise and p-channel JFETs for high speed performance, the output voltage of the OP275 may exhibit phase reversal if either of its inputs exceeds its negative common-mode input voltage. This might occur in very severe industrial appli ...
Bass Amp schematic
... Ampeg B-15-NF preamp through tone stack. Two changes: first grid leak resistor dropped to 1M from 5.6M for noise reasons: 1) had to use carbon film instead of quieter metal for 5.6M, and 2) thermal noise, which is proportional to the square root of the resistance. Second change was to make tip-ring ...
... Ampeg B-15-NF preamp through tone stack. Two changes: first grid leak resistor dropped to 1M from 5.6M for noise reasons: 1) had to use carbon film instead of quieter metal for 5.6M, and 2) thermal noise, which is proportional to the square root of the resistance. Second change was to make tip-ring ...
