FAN4852 9MHz Low-Power Dual CMOS Amplifier FAN48
... operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Functional operat ...
... operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Functional operat ...
THE JOHN HARDY co. I - technicalaudio.com
... the transformer step-up of 5.6 d8, with a bandwldth of 120 kHZ (-3 dB). The Jensen JE 16-AlB mic-input transformer was designed specifically for the 990 • Cl is used to keep the DC offset of the 990 constant by AC-coup ling the gain-a~just pot. Without this capacitor. the DC offset would change as t ...
... the transformer step-up of 5.6 d8, with a bandwldth of 120 kHZ (-3 dB). The Jensen JE 16-AlB mic-input transformer was designed specifically for the 990 • Cl is used to keep the DC offset of the 990 constant by AC-coup ling the gain-a~just pot. Without this capacitor. the DC offset would change as t ...
SGA1263Z 数据资料DataSheet下载
... Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Abs ...
... Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Abs ...
TDE1737
... specifically to drive lamps, relays and control of stepper motors. This device is essentially blow-out proof. Current limiting is available to limit the peak output current to a safe value, the adjustment only requires one external resistor. In addition, thermal shut down is provided to keep the I.C ...
... specifically to drive lamps, relays and control of stepper motors. This device is essentially blow-out proof. Current limiting is available to limit the peak output current to a safe value, the adjustment only requires one external resistor. In addition, thermal shut down is provided to keep the I.C ...
Chapter 1 Introduction to Electronics
... • An electronic circuit generally contains both the passive and active components. Therefore a dc power supply is essential for the operation of its active components. An electronic processing or amplifier devices also need different power source than its DC operating power source called input signa ...
... • An electronic circuit generally contains both the passive and active components. Therefore a dc power supply is essential for the operation of its active components. An electronic processing or amplifier devices also need different power source than its DC operating power source called input signa ...
AD8005
... Capacitive loads interact with an op amp’s output impedance to create an extra delay in the feedback path. This reduces circuit stability, and can cause unwanted ringing and oscillation. A given value of capacitance causes much less ringing when the amplifier is used with a higher noise gain. The ca ...
... Capacitive loads interact with an op amp’s output impedance to create an extra delay in the feedback path. This reduces circuit stability, and can cause unwanted ringing and oscillation. A given value of capacitance causes much less ringing when the amplifier is used with a higher noise gain. The ca ...
DN254 - LT1806: 325MHz Low Noise Rail-to-Rail SOT-23 Op Amp Saves Board Space
... capacitance and noise gain. Table 1 and Figure 3 show the bandwidth and noise performance achieved with several large-area photodiodes (and a small-area SFH213 for comparison). Note that large-area detectors also place extra demands on the gain bandwidth of an amplifier. The final case in Table 1 s ...
... capacitance and noise gain. Table 1 and Figure 3 show the bandwidth and noise performance achieved with several large-area photodiodes (and a small-area SFH213 for comparison). Note that large-area detectors also place extra demands on the gain bandwidth of an amplifier. The final case in Table 1 s ...
Instrumentation: 206 L
... assign values to the points marked a through e 2. For the same circuit determine the output voltage if V1 = 1 V, V2 = 5V, R1= R3 = 5kΩ, and R2 = R4 = 4 x R1. ...
... assign values to the points marked a through e 2. For the same circuit determine the output voltage if V1 = 1 V, V2 = 5V, R1= R3 = 5kΩ, and R2 = R4 = 4 x R1. ...