Chapter 4: RF/IF Circuits
... amplifier. Also, the modulation bandwidth is typically very much smaller than the carrier frequency. A second mixer stage converts the signal to the baseband. The signal is then demodulated (demod). The modulation technique is independent from the receiver technology. The modulation scheme could be ...
... amplifier. Also, the modulation bandwidth is typically very much smaller than the carrier frequency. A second mixer stage converts the signal to the baseband. The signal is then demodulated (demod). The modulation technique is independent from the receiver technology. The modulation scheme could be ...
UCC28220-Q1 数据资料 dataSheet 下载
... this signal. The linear operating range on this input is 0 to 1.5 V. Also, this pin is pulled to ground each time its respective output goes low (i.e., OUT1 or OUT2). SLOPE: This pin sets up a current used for the slope compensation ramp. A resistor to ground sets up a current, which is internally d ...
... this signal. The linear operating range on this input is 0 to 1.5 V. Also, this pin is pulled to ground each time its respective output goes low (i.e., OUT1 or OUT2). SLOPE: This pin sets up a current used for the slope compensation ramp. A resistor to ground sets up a current, which is internally d ...
LM2594 0.5 A, Step-Down Switching Regulator
... Inductance Region = L20 D. Proper inductor value = 100 mH Choose the inductor from Table 3. ...
... Inductance Region = L20 D. Proper inductor value = 100 mH Choose the inductor from Table 3. ...
TLC320AD545 数据资料 dataSheet 下载
... 5–2 ADC Decimation Filter Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–6 5–3 ADC Decimation Filter Passband Ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7 5–4 DAC Interpolation Filter Response . . . . . . . . . . . . . . . . . . . . . . . . . ...
... 5–2 ADC Decimation Filter Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–6 5–3 ADC Decimation Filter Passband Ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5–7 5–4 DAC Interpolation Filter Response . . . . . . . . . . . . . . . . . . . . . . . . . ...
Bias Circuits for RF Devices
... A lot of RF schematics mention: “bias circuit not shown”; when actually one of the most critical yet often overlooked aspects in any RF circuit design is the bias network. The bias network determines the amplifier performance over temperature as well as RF drive. The DC bias condition of the RF tran ...
... A lot of RF schematics mention: “bias circuit not shown”; when actually one of the most critical yet often overlooked aspects in any RF circuit design is the bias network. The bias network determines the amplifier performance over temperature as well as RF drive. The DC bias condition of the RF tran ...
EE 321 Analog Electronics, Fall 2011 Homework #7 solution
... VT This is tabulated in the third column. The minimum output voltage swing is determined by the edge of saturation, vCE,sat = 0.3 V. It is ...
... VT This is tabulated in the third column. The minimum output voltage swing is determined by the edge of saturation, vCE,sat = 0.3 V. It is ...
ACF2101 Low Noise, Dual SWITCHED INTEGRATOR APPLICATIONS
... The ACF2101 is a dual switched integrator for precision applications. Each channel can convert an input current to an output voltage by integration, using either an internal or external capacitor. Included on the chip are precision 100pF integration capacitors, hold and reset switches, and output mu ...
... The ACF2101 is a dual switched integrator for precision applications. Each channel can convert an input current to an output voltage by integration, using either an internal or external capacitor. Included on the chip are precision 100pF integration capacitors, hold and reset switches, and output mu ...
THS4509-Q1
... (2-V step), it is ideal for pulsed applications. It is designed for minimum gain of 6 dB but is optimized for gain of 10 dB. To allow for dc coupling to analog-to-digital converters (ADCs), its unique output common-mode control circuit maintains the output common-mode voltage within 3-mV offset (typ ...
... (2-V step), it is ideal for pulsed applications. It is designed for minimum gain of 6 dB but is optimized for gain of 10 dB. To allow for dc coupling to analog-to-digital converters (ADCs), its unique output common-mode control circuit maintains the output common-mode voltage within 3-mV offset (typ ...
