ADS801 数据资料 dataSheet 下载
... pipelining. It uses a fully differential architecture and digital error correction to ensure 12-bit resolution. The differential track-and-hold circuit is shown in Figure 1. The switches are controlled by an internal clock that is a non-overlapping 2phase signal, φ1 and φ2. At the sampling time, the ...
... pipelining. It uses a fully differential architecture and digital error correction to ensure 12-bit resolution. The differential track-and-hold circuit is shown in Figure 1. The switches are controlled by an internal clock that is a non-overlapping 2phase signal, φ1 and φ2. At the sampling time, the ...
DAC8806 数据资料 dataSheet 下载
... Each DAC code determines the 2R-leg switch position to either GND or IOUT. The external I/V converter op amp noise gain will also change because the DAC output impedance (as seen looking into the IOUT terminal) changes versus code. Because of this, the external I/V converter op amp must have a suffi ...
... Each DAC code determines the 2R-leg switch position to either GND or IOUT. The external I/V converter op amp noise gain will also change because the DAC output impedance (as seen looking into the IOUT terminal) changes versus code. Because of this, the external I/V converter op amp must have a suffi ...
ADM485E 数据手册DataSheet 下载
... The ADM487E and ADM1487E have a 1/4 unit load receiver input impedance that allows up to 128 transceivers on a bus, whereas the ADM485E allows up to 32 transceivers on a bus. Because only one driver is enabled at any time, the output of a disabled or power-down driver is three-stated to avoid overlo ...
... The ADM487E and ADM1487E have a 1/4 unit load receiver input impedance that allows up to 128 transceivers on a bus, whereas the ADM485E allows up to 32 transceivers on a bus. Because only one driver is enabled at any time, the output of a disabled or power-down driver is three-stated to avoid overlo ...
LTC6405
... Note 4: The LTC6405C/LTC6405I are guaranteed functional over the operating temperature range –40°C to 85°C. Note 5: The LTC6405C is guaranteed to meet specified performance from 0°C to 70°C. The LTC6405C is designed, characterized, and expected to meet specified performance from –40°C to 85°C but is n ...
... Note 4: The LTC6405C/LTC6405I are guaranteed functional over the operating temperature range –40°C to 85°C. Note 5: The LTC6405C is guaranteed to meet specified performance from 0°C to 70°C. The LTC6405C is designed, characterized, and expected to meet specified performance from –40°C to 85°C but is n ...
Single axis devices
... Switching frequency of the power output stage can be set................................................................9 Optimization of the predefined external setpoint via the analog input ................................................9 UL certification.......................................... ...
... Switching frequency of the power output stage can be set................................................................9 Optimization of the predefined external setpoint via the analog input ................................................9 UL certification.......................................... ...
8-Ch Parallel 1-A High-Side Digital Output
... low-cost microcomputer with Linux operating system. This makes the evaluation of our featured components very easy. With this methodology, it is possible to test all components in the target environment, which is an industrial switching cabinet for factory automation. The TIDA-00183 has all necessar ...
... low-cost microcomputer with Linux operating system. This makes the evaluation of our featured components very easy. With this methodology, it is possible to test all components in the target environment, which is an industrial switching cabinet for factory automation. The TIDA-00183 has all necessar ...
a LC MOS 4-Channel, 12-Bit Simultaneous Sampling Data Acquisition System
... Conversion is initiated on the rising edge of CONVST. All four input track/holds go from track to hold on this edge. Conversion is first performed on the Channel 1 input voltage, then Channel 2 is converted and so on. The four results are stored in on-chip registers. When all four conversions have b ...
... Conversion is initiated on the rising edge of CONVST. All four input track/holds go from track to hold on this edge. Conversion is first performed on the Channel 1 input voltage, then Channel 2 is converted and so on. The four results are stored in on-chip registers. When all four conversions have b ...
