
Resistors
... Resistors have been used in most of the electrical labs of this course so far, but they have not been described in detail, nor has their electrical purposes been given, other than to limit current. In this lesson, resistors will be discussed in some detail, and the variety of electrical components t ...
... Resistors have been used in most of the electrical labs of this course so far, but they have not been described in detail, nor has their electrical purposes been given, other than to limit current. In this lesson, resistors will be discussed in some detail, and the variety of electrical components t ...
MAX3223E 数据资料 dataSheet 下载
... The MAX3223E consists of two line drivers, two line receivers, and a dual charge-pump circuit with ±15-kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communica ...
... The MAX3223E consists of two line drivers, two line receivers, and a dual charge-pump circuit with ±15-kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communica ...
datasheet - Texas Instruments
... Each VCC pin should have a good bypass capacitor to prevent power disturbance. For devices with a single supply, a 0.1-μF capacitor is recommended; if there are multiple VCC pins then a 0.01-μF or 0.022-μF capacitor is recommended for each power pin. It is acceptable to parallel multiple bypass caps ...
... Each VCC pin should have a good bypass capacitor to prevent power disturbance. For devices with a single supply, a 0.1-μF capacitor is recommended; if there are multiple VCC pins then a 0.01-μF or 0.022-μF capacitor is recommended for each power pin. It is acceptable to parallel multiple bypass caps ...
Transmission Gate Characteristics
... The transmissionn gate is on when en=5V and enb=0V, assuming the bulk of PMOS is connected to VDD(=5V) and the bulk of NMOS is connected to GND(=0V). In the on condition the output signal “out” will follows the input signal “in”. The operation of each transistor will first be analyzed. The NMOS swit ...
... The transmissionn gate is on when en=5V and enb=0V, assuming the bulk of PMOS is connected to VDD(=5V) and the bulk of NMOS is connected to GND(=0V). In the on condition the output signal “out” will follows the input signal “in”. The operation of each transistor will first be analyzed. The NMOS swit ...
BDTIC T D A 5 2 2 0
... The LNA is an on-chip cascode amplifier with a voltage gain of 15 to 20dB. The gain figure is determined by the external matching networks situated ahead of LNA and between the LNA output LNO (Pin 6) and the Mixer Inputs MI and MIX (Pins 8 and 9). The noise figure of the LNA is approximately 3dB, th ...
... The LNA is an on-chip cascode amplifier with a voltage gain of 15 to 20dB. The gain figure is determined by the external matching networks situated ahead of LNA and between the LNA output LNO (Pin 6) and the Mixer Inputs MI and MIX (Pins 8 and 9). The noise figure of the LNA is approximately 3dB, th ...
Octal Channel Protectors ADG467 FEATURES
... the output of the channel protector (no load) is clamped at these threshold voltages. However, the channel protector output clamps at a voltage value that is inside these thresholds if the output is loaded. For example, with an output load of 1 kΩ, VDD = 15 V, and a positive overvoltage on the input ...
... the output of the channel protector (no load) is clamped at these threshold voltages. However, the channel protector output clamps at a voltage value that is inside these thresholds if the output is loaded. For example, with an output load of 1 kΩ, VDD = 15 V, and a positive overvoltage on the input ...
AN10436 TDA8932B/33(B) Class-D audio amplifier Rev. 01 — 12 December 2007 Application note
... The TDA8933(B) device is the low-power version that delivers an output power of 2 × 5 WRMS to 2 × 15 WRMS in a SE configuration or 10 WRMS to 30 WRMS in a BTL configuration. This high efficiency SMA device has been designed to operate without a heat sink and has the flexibility to operate from eithe ...
... The TDA8933(B) device is the low-power version that delivers an output power of 2 × 5 WRMS to 2 × 15 WRMS in a SE configuration or 10 WRMS to 30 WRMS in a BTL configuration. This high efficiency SMA device has been designed to operate without a heat sink and has the flexibility to operate from eithe ...
LT1806/LT1807 - 325MHz, Single/Dual, Rail-to-Rail Input and Output, Low Distortion, Low Noise Precision Op Amps
... The LT®1806/LT1807 are single/dual low noise rail-to-rail input and output unity-gain stable op amps that feature a 325MHz gain-bandwidth product, a 140V/μs slew rate and a 85mA output current. They are optimized for low voltage, high performance signal conditioning systems. The LT1806/LT1807 have a ...
... The LT®1806/LT1807 are single/dual low noise rail-to-rail input and output unity-gain stable op amps that feature a 325MHz gain-bandwidth product, a 140V/μs slew rate and a 85mA output current. They are optimized for low voltage, high performance signal conditioning systems. The LT1806/LT1807 have a ...