
MAX15569 2-Phase/1-Phase QuickTune-PWM Controller with Serial I C Interface
... Connect a resistor (RFB) between FB and the positive output of the remote sense (output) to set the DC steady-state droop. The impedance from FBAC to FB sets the current-loop gain over frequency, which dominates stability. See the Load-Line Amplifier (Steady State and AC Droop) section. Current Moni ...
... Connect a resistor (RFB) between FB and the positive output of the remote sense (output) to set the DC steady-state droop. The impedance from FBAC to FB sets the current-loop gain over frequency, which dominates stability. See the Load-Line Amplifier (Steady State and AC Droop) section. Current Moni ...
MAX4245/MAX4246/MAX4247 Ultra-Small, Rail-to-Rail I/O with Disable, Single-/Dual-Supply, Low-Power Op Amps General Description
... op amps offer rail-to-rail inputs and outputs, draw only 320µA of quiescent current, and operate from a single +2.5V to +5.5V supply. For additional power conservation, the MAX4245/MAX4247 offer a low-power shutdown mode that reduces supply current to 50nA, and puts the amplifiers’ outputs in a high ...
... op amps offer rail-to-rail inputs and outputs, draw only 320µA of quiescent current, and operate from a single +2.5V to +5.5V supply. For additional power conservation, the MAX4245/MAX4247 offer a low-power shutdown mode that reduces supply current to 50nA, and puts the amplifiers’ outputs in a high ...
LTM9001-Ax/LTM9001-Bx - 16-Bit IF/Baseband Receiver Subsystem
... Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to ground with GND and OGND wired together (unless otherwise noted). Note 3: Gain is measured from IN+/IN– through the ADC. The amplifier gain is attenuated by the filt ...
... Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: All voltage values are with respect to ground with GND and OGND wired together (unless otherwise noted). Note 3: Gain is measured from IN+/IN– through the ADC. The amplifier gain is attenuated by the filt ...
TPS748 1.5-A Low-Dropout Linear Regulator
... The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted from the simulation data to obtain θJA using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-board characterization parameter, ψJB, estimates t ...
... The junction-to-top characterization parameter, ψJT, estimates the junction temperature of a device in a real system and is extracted from the simulation data to obtain θJA using a procedure described in JESD51-2a (sections 6 and 7). The junction-to-board characterization parameter, ψJB, estimates t ...
AD7863 数据手册DataSheet下载
... input ranges. The AD7863-10 offers the standard industrial input range of ±10 V; the AD7863-3 offers the common signal processing input range of ±2.5 V, while the AD7863-2 can be used in unipolar 0 V to 2.5 V applications. The part features very tight aperture delay matching between the two input sa ...
... input ranges. The AD7863-10 offers the standard industrial input range of ±10 V; the AD7863-3 offers the common signal processing input range of ±2.5 V, while the AD7863-2 can be used in unipolar 0 V to 2.5 V applications. The part features very tight aperture delay matching between the two input sa ...
$doc.title
... drift and high input impedance. In addition, the TLC27L1 is a low-bias version of the TLC271 programmable amplifier. These devices use the Texas Instruments silicon-gate LinCMOS technology, which provides offset-voltage stability far exceeding the stability available with conventional metal-gate pr ...
... drift and high input impedance. In addition, the TLC27L1 is a low-bias version of the TLC271 programmable amplifier. These devices use the Texas Instruments silicon-gate LinCMOS technology, which provides offset-voltage stability far exceeding the stability available with conventional metal-gate pr ...
Sequential Logic
... The operating points (Q-points) for this circuit must lie on the voltage transfer curve. Furthermore the loop connection imposes that the input and output voltages must be the same. Therefore the “load line” of this circuit is a line of slope 1 as indicated on Figure 3. The operating points must als ...
... The operating points (Q-points) for this circuit must lie on the voltage transfer curve. Furthermore the loop connection imposes that the input and output voltages must be the same. Therefore the “load line” of this circuit is a line of slope 1 as indicated on Figure 3. The operating points must als ...
ADC音频放大器系列SSM2319 数据手册DataSheet 下载
... with <1% total harmonic distortion (THD) 90% efficiency at 5.0 V, 1.4 W into 8 Ω speaker Signal-to-noise ratio (SNR): 98 dB Single-supply operation: 2.5 V to 5.5 V Ultralow shutdown current: 20 nA Short-circuit and thermal protection with autorecovery Available in 9-ball, 1.5 mm × 1.5 mm WLCSP Pop-a ...
... with <1% total harmonic distortion (THD) 90% efficiency at 5.0 V, 1.4 W into 8 Ω speaker Signal-to-noise ratio (SNR): 98 dB Single-supply operation: 2.5 V to 5.5 V Ultralow shutdown current: 20 nA Short-circuit and thermal protection with autorecovery Available in 9-ball, 1.5 mm × 1.5 mm WLCSP Pop-a ...
TLV271-Q1, TLV272-Q1, TLV274-Q1 µA/Ch 3-MHz RAIL-TO-RAIL OUTPUT FAMILY OF 550-
... The TLV27x takes the minimum operating supply voltage down to 2.7 V over the extended automotive temperature range while adding the rail-to-rail output swing feature. This makes it an ideal alternative to the TLC27x family for applications where rail-to-rail output swings are essential. The TLV27x a ...
... The TLV27x takes the minimum operating supply voltage down to 2.7 V over the extended automotive temperature range while adding the rail-to-rail output swing feature. This makes it an ideal alternative to the TLC27x family for applications where rail-to-rail output swings are essential. The TLV27x a ...
BQ24751B 数据资料 dataSheet 下载
... Charge voltage set reference input. Connect the VREF or external DAC voltage source to the VDAC pin. Battery voltage, charge current, and input current are programmed as a ratio of the VDAC pin voltage versus the VADJ, SRSET, and ACSET pin voltages, respectively. Place resistor dividers from VDAC to ...
... Charge voltage set reference input. Connect the VREF or external DAC voltage source to the VDAC pin. Battery voltage, charge current, and input current are programmed as a ratio of the VDAC pin voltage versus the VADJ, SRSET, and ACSET pin voltages, respectively. Place resistor dividers from VDAC to ...