A Voltage-Controlled Filter
... The LPV511 is a micropower op amp that operates from a voltage supply range as wide as 2.7V to 12V. This device exhibits an excellent speed-to-power ratio, drawing only 880 nA of supply current with a unity gain bandwidth of 27 kHz. The input range includes both supply rails for ground and high-side ...
... The LPV511 is a micropower op amp that operates from a voltage supply range as wide as 2.7V to 12V. This device exhibits an excellent speed-to-power ratio, drawing only 880 nA of supply current with a unity gain bandwidth of 27 kHz. The input range includes both supply rails for ground and high-side ...
Slide 1
... (I or V) taken while another parameter is constant (V or I) Used to study the reliability of the Dielectric and to predict the life time Since a particular source (I or V) is applied for a longer period of time, the effect of I or V stress can be studied. (Temperature stress is also possible) ...
... (I or V) taken while another parameter is constant (V or I) Used to study the reliability of the Dielectric and to predict the life time Since a particular source (I or V) is applied for a longer period of time, the effect of I or V stress can be studied. (Temperature stress is also possible) ...
195 Series Models: 1952 1953 1954
... Safety (dielectric test, leakage and other hazards): instruments are equal to or better than ANSI C39.5-1974. The above tolerance limits apply to the standard ranges listed in this bulletin. Special instruments may vary from these limits. Rated circuit to ground voltage = 800 Vrms (1100 Peak). ...
... Safety (dielectric test, leakage and other hazards): instruments are equal to or better than ANSI C39.5-1974. The above tolerance limits apply to the standard ranges listed in this bulletin. Special instruments may vary from these limits. Rated circuit to ground voltage = 800 Vrms (1100 Peak). ...
U-153 UC3855A/B High Performance Power Factor Preregulator
... In order to increase the switching frequency while maintaining acceptable efficiency, several soft switching techniques have been developed [1,2,3]. Most of these resonant techniques increase the semiconductor current and/or voltage stress, leading to larger devices and increased conduction losses d ...
... In order to increase the switching frequency while maintaining acceptable efficiency, several soft switching techniques have been developed [1,2,3]. Most of these resonant techniques increase the semiconductor current and/or voltage stress, leading to larger devices and increased conduction losses d ...
International Electrical Engineering Journal (IEEJ) Vol. 5 (2014) No.12, pp. 1673-1679
... The Load changes the voltage Variation in transmission lines must be limited, otherwise the consumer’s equipments are damaged at distributed side. For reducing this voltage variation a FACTS device called Distributed Power Flow Controller (DPFC) and Distributed Interline Power Flow Controller (DIPFC ...
... The Load changes the voltage Variation in transmission lines must be limited, otherwise the consumer’s equipments are damaged at distributed side. For reducing this voltage variation a FACTS device called Distributed Power Flow Controller (DPFC) and Distributed Interline Power Flow Controller (DIPFC ...
SICAM-Q200
... Harmonics of voltages, currents, and powers up to the 63rd order according to the IEC 61000-4-7 standard. The following values are given for each harmonic: • RMS value (for power: RMS value and sign) • Phase angle The sign of the active power of the single harmonic can indicate the direction of the ...
... Harmonics of voltages, currents, and powers up to the 63rd order according to the IEC 61000-4-7 standard. The following values are given for each harmonic: • RMS value (for power: RMS value and sign) • Phase angle The sign of the active power of the single harmonic can indicate the direction of the ...
Product Selection Guide OptiMOS and StrongIRFET Combined
... For low frequency applications, OptiMOS™ 5 is the best fit when best-in-class performance is required. However, StrongIRFET™ is recommended for 20 V to 75 V applications when best-inclass performance is not essential and cost is a more significant consideration. For best-in-class performance at volt ...
... For low frequency applications, OptiMOS™ 5 is the best fit when best-in-class performance is required. However, StrongIRFET™ is recommended for 20 V to 75 V applications when best-inclass performance is not essential and cost is a more significant consideration. For best-in-class performance at volt ...
The World`s Smallest Code-Practice Oscillator
... at U1 pin 5 is 0 V, Q1 is off; when the voltage at pin 5 is greater than 1.5 V, Q1 is on. This action pulses current through the speaker at a 700-Hz rate and you hear the tone. Pretty simple, isn’t it? Despite the circuit’s simplicity, it offers advantages over similar circuits built with older-tech ...
... at U1 pin 5 is 0 V, Q1 is off; when the voltage at pin 5 is greater than 1.5 V, Q1 is on. This action pulses current through the speaker at a 700-Hz rate and you hear the tone. Pretty simple, isn’t it? Despite the circuit’s simplicity, it offers advantages over similar circuits built with older-tech ...
Evaluates: MAX1982/MAX1983 MAX1982 Evaluation Kit General Description Features
... 1.2V output voltage while operating on input voltages from 1.25V to 5.5V. It delivers a 0.3A output current from a 1.25V to 2.5V input, with less than 300mV dropout. Operation with higher input voltages (up to 5.5V) is possible as long as the maximum power dissipation across the internal pass transi ...
... 1.2V output voltage while operating on input voltages from 1.25V to 5.5V. It delivers a 0.3A output current from a 1.25V to 2.5V input, with less than 300mV dropout. Operation with higher input voltages (up to 5.5V) is possible as long as the maximum power dissipation across the internal pass transi ...
lecture 3:common-emitter amplifier
... Ac load line -> visualizing r/ship between smallsignal response and transistor characteristic. Ac operating region is on ac load line. ...
... Ac load line -> visualizing r/ship between smallsignal response and transistor characteristic. Ac operating region is on ac load line. ...
Buck converter
A buck converter is a voltage step down and current step up converter.The simplest way to reduce the voltage of a DC supply is to use a linear regulator (such as a 7805), but linear regulators waste energy as they operate by dissipating excess power as heat. Buck converters, on the other hand, can be remarkably efficient (95% or higher for integrated circuits), making them useful for tasks such as converting the main voltage in a computer (12V in a desktop, 12-24V in a laptop) down to the 0.8-1.8V needed by the processor.