* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download fault-relay reo1 - Hansen Electric spol. s ro
Mercury-arc valve wikipedia , lookup
Electric machine wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Ground (electricity) wikipedia , lookup
Ground loop (electricity) wikipedia , lookup
Stepper motor wikipedia , lookup
Thermal runaway wikipedia , lookup
Electrical substation wikipedia , lookup
Current source wikipedia , lookup
Power electronics wikipedia , lookup
History of electric power transmission wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Three-phase electric power wikipedia , lookup
Voltage optimisation wikipedia , lookup
Buck converter wikipedia , lookup
Stray voltage wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Surge protector wikipedia , lookup
Opto-isolator wikipedia , lookup
Alternating current wikipedia , lookup
Mains electricity wikipedia , lookup
FAULT-RELAY REO1 It is determined for protection of three-phase electric motors. It consists of the following individual parts: Thermistor tripping relay KLH Monitoring relay ZLS Earth leakage relay UP6R Overcurrent relay LH86 supplemented with current measurement Thermistor tripping relay KLH provides protection for electric motors from excessive warming. Temperature increase is registered by temperature-sensitive sensors - thermistors with positive thermal coefficient PTC. Monitoring relay ZLS is determined for realization of time-delay in control circuits. The switching time delay can be set up at 0,1 to 10s. Breaking occurs immediately after the supply has been switched off. Earth leakage relay UP6R is used for supervision over the state of isolation of electric networks and connected devices. After reduction of isolation resistance below the set-up value of the circuit, the relay signals failure by means of its contacts. The electronic overcurrent relay LH86 along with the corresponding converters of current/voltage is determined for protection from thermal effects of overcurrents and for protection from effects of short-circuit currents of three-phase electric motors. It is also equipped with optional guarding of phase fall-out. Using switches and potentiometers we can select the nominal current of the electric motor in a wide range from 2.1A to 750A, the size of short-circuit current in range from 3 to 12xIn and also some of the three tripping characteristics. The whole unit is placed in a plastic box and it is mechanically fixed by means of a mounting screw. On the front part there are control units, on the top there are three holes blinded with a bushing seal providing access to the DIP switches. The cover is labelled to provide description of outlets connection, description of switches and characteristics of overcurrent and short-circuit protection. Relays of individual protections have switching contacts individually led out onto the connector where the contacts remain closed until a failure occurs. The breaking contacts whose one pole is interconnected are not closed until a failure occurs. Output circuits KLH and UP6R are classified as intrinsically safe (not flammable by K56007-67_0391_A spark) according to standpoint No.00/0047 SZ No.210 of Physical Technical Testing Institute in OstravaRadvanice. Technical data Supply voltage Total consumption including ZLS Dimensions Permitted ambient temperature Outlet contacts Coverage range Part KLH Measuring voltage Short-circuit current in measuring circuit Max. inductance of guarding loop Max. capacity of guarding loop Tripping value of resistance Value of transition into basic state Part ZLS Supply voltage Input power Time Part UP6R Measuring voltage Short-circuit current in measuring circuit Max. inductance of guarding loop Max. capacity of guarding loop Tripping resistance Part LH86 Range IN: for sensor 3mV/A for sensor 1mV/A Tripping characteristics Tripping at short-circuit Optional starting delay K56007-67_0391_A AC 42V, +15%, -20%, 40..60Hz 140mA; 5,9VA 144x40x120mm from -10°C to 60°C 42V/5A IP30 ca 2,3V max. 23mA 1mH 500nF 13..14kOhm 6..7kOhm AC 42V, +15%, -20%, 40..60Hz 1.2VA from 0.1 to 10s DC 20V max. 5.5mA 1mH 500nF when being produced, adjustable from 5 to 250kOhm 2.1 to 250A 6.3 to 750A 5s, 8s, 20s (time gives tripping at 6xIN) 3 to 12IN 10ms